Manual Winix 6300-2 Air Purifier

Manual

1

4

2

5

3

6

FRONT

PACKAGE CONTENTS

BACK

Air Outlet

Vent

Handle

Power Plug

Remote Control and User Manual will be

located on the top insert after the box is opened.

Control Panel

Front Panel

Unit

)RUD&HUWLHG5HIXUELVKHG$LU3XULHU

there will be 4 New Carbon Filters and 1 True HEPA Filter included; equivalent to a 1-year supply.

(1) Pre-Filter

(8) Activated Carbon Filters

(1) True HEPA Filter

Remote

Control

User

Manual

WHERE TO USE

MODEL PART DIAGRAM

12~18 in

12~18 in

Allow 12 ~ 18 in. of space between TVs, radios, and other electronics

Electromagnetic interference from certain electronics may cause

product malfunction.

Place indoors away from direct sunlight

Direct exposure may cause product malfunction or failure.

Only place on hard, flat surfaces

Flimsy or slanted surfaces may result in abnormal noise and vibrations.

Allow at least 12 ~ 18 in. from walls for maximum air flow

10

11 14 1512

13

09

02 03 04 05 06 07 0801

CONTROL PANEL

When to Replace Filters

Filter Indicator Light When to Service When to Replace

Pre-Filter

none Clean once every 14 days Permanent

Activated Carbon

Filter

none

Can NOT be WASHED

Replace every 3 months

True HEPA Filter

Last Approx. 12 months

• When the Check Filter Indicator LED is on, it is time to replace the True HEPA Filter and Activated Carbon Filter.

• Intervals between filter replacement may vary depending on environment.

MAINTENANCE

True HEPA Filter

03

Activated Carbon Filter

02

PlasmaWave

04

Pre-Filter

01

®

4-STAGE AIR PURIFICATION

01. Pre-Filter

Designed to catch larger airborne particles found

indoors.

03. True HEPA Filter

Winix True HEPA captures 99.99%* of airborne

allergens including pollen, dust, smoke, pet dander,

and other ultrafine particles as small as 0.003

microns.

* Based on independent laboratory tests conducted

on inanimate particles as small as 0.003 microns.

02. Activated Carbon Filter

Reduces VOCs and household odors from cooking,

pets, and smoke.

04. PlasmaWave

®

Winix PlasmaWave

®

Technology may help to reduce

airbone contaminants*.

* Tested by an independent third-party laboratory.

Visit www.winixamerica.com for more details.

INITIAL OPERATION

Latch

1.

Remove the front panel by grasping its upper

edge and gently pulling forward.

2.

Remove the Pre-Filter, then the plastic bag of

filters behind it.

3.

Remove filters from protective plastic bag.

02

03

01

4.

Install the filters until they fit securely in place.

03. True HEPA Filter (back)

02. Activated Carbon Filter (middle)

01. Pre-Filter (front)

Latch

5.

After filters are installed, close the front panel.

6.

Insert the power cord into an electrical outlet.

REPLACING FILTERS

CLEANING CARE

Cleaning the Filters:

Use a vacuum cleaner or soft brush to clean the Pre-Filter

• If it is excessively soiled, rinse in room temperature

water.

• Do not use detergent or soap.

• Allow the filter to dry for 24 hours or more before using.

• Intervals between filter cleaning may vary depending

on the air quality in the environment.

NOTICE

• Do not use benzene, alcohol, or other volatile fluids,

which may cause damage or discoloration.

• Do not use hot water over 104

o

F.

Cleaning the Exterior & Interior:

1.

Open the front panel and clean the interior with a

vacuum cleaner.

• A handheld vacuum or hose attachment will work best.

2.

Dampen a cloth with room temperature water and

wipe down the interior and exterior of the unit.

3.

Wipe the unit down with a clean, dry cloth.

• Ensure no moisture remains before plugging the unit

back in.

* For optimal performance, clean every 1 - 2 months.

NOTICE

• When cleaning the unit, always unplug the power cord

first and then wait until the unit has cooled down.

• Never disassemble, repair, or modify this unit yourself.

• Do not use flammable sprays or liquid detergents.

• Do not allow children to clean or maintain the unit.

• Before cleaning or maintaining, ensure unit is unplugged.

01. Auto Indicator

Indicates whether Auto Mode is enabled or disabled.

02. Sleep Indicator

Indicates whether Sleep Mode is enabled or disabled.

03. PlasmaWave

®

Indicator

Indicates whether PlasmaWave

®

is enabled or

disabled.

04. Fan Speed Indicator

Indicates the current fan speed.

05. Timer Indicator

If timer has been set, the LED light indicates the set time

of operation.

06. Filter Replacement Indicator

LED light indicates when it is time to change the filter.

07. Light Sensor

Detects the amount of ambient light in the

environment.

08. Smart Sensor

Detects the amount of odorous gas in the

environment. When in Auto mode, the fan speed

adjusts according to the detected amount of gas.

09. Power Button

Turns the unit on or off.

During the first 30 seconds of powering up, the Air

Quality Indicator will cycle through Blue, Amber

and Red colors. Smart Sensor takes approximately

4minutes to detect the air quality in the environment

before normal operation begins.

10. Mode Button

Press to cycle through to set the mode of operation

(Auto, Sleep). The unit will default to Auto with

PlasmaWave

®

enabled when first powered on.

• Auto Mode:

- Auto Mode automatically adjusts fan speeds

according to your indoor air quality. The fan speed

will adjust to low when air quality is good, medium

when fair, and to high when poor.

• Sleep Mode:

- When Sleep Mode is activated, the Air Quality

Indicator LED light is disabled.

- Fan speed will automatically set to minimum

speed (lower than 'Low') which will be nearly silent.

- When Sleep Mode is active, PlasmaWave

®

will be

disabled, but it can be turned back on.

11. PlasmaWave

®

Button

Enables or disables PlasmaWave

®

.

"When the unit is running, you may hear a chirping or

buzzing sound. The sound is from large particles passing

through PlasmaWave

®

, it is normal and does not signify

product failure."

Press the PlasmaWave

®

button when the unit is on

to enable or disable this feature.

12. Air Quality Indicator

Color coded LED light indicates one of three levels of

Air Quality: Red (poor), Amber (fair), and Blue (good).

13. Fan Speed Button

Enables manual operation of the unit's fan speeds.

• Press to cycle through and set the desired fan speed

(Low, Medium, High, Turbo).

14. Timer Button

Press to cycle through and set desired length of

operation (1hr, 4hr, 8hr, [NO TIMER]).

15. Filter Reset Button

After replacing the filter, turn on the unit and then use

a thin object, such as a paper clip, to press the Filter

Reset Button for 5 seconds.

REMOTE CONTROL

Operates in a 20 foot radius:

A

C

B

D

• (A) Power: Turns the unit on or off.

• (B) Auto: Enables Auto Mode.

• (C) Fan Speed: Enables manual

operation of the fan speeds.

• (D) Turbo: Enters Manual Mode

and directly sets the fan speed to

Turbo.

How to replace your remote’s battery:

1.A

1.B

2.A

3.A

1.

Flip over your remote and open

battery tray.

1.A: Pinch the lever in while,

1.B: Pulling the battery tray out.

2.

Insert battery into the battery

tray as shown.

2.A: Make sure the polarities [+]

[-] match when placing in the tray

.

3.

Close the battery tray.

3.A

: Reinsert battery tray into

remote until you hear a "click"

sound.

ę

Keep all used batteries (CR2025) in safe place.

WARNING

• Incorrect battery usage may cause battery fluid leakage

and/or damage.

• When not using remote for extended periods of time,

remove the battery.

• Avoid dropping or damaging the remote.

• WARNING: Chemical Burn Hazard. Keep batteries away

from children.

• This product contains a lithium button/coin cell

battery. If a new or used lithium button/coin cell battery

is swallowed or enters the body, it can cause severe

internal burns and can lead to death in as little as

2 hours.

• Always completely secure the battery compartment.

• If the battery compartment does not close securely,

stop using the product, remove the batteries, and keep

it away from children.

• If you think batteries might have been swallowed or

placed inside any part of the body, seek immediate

medical attention.

• The batteries should be disposed of properly, including

keeping them away from children. Even used batteries

may cause injury.

Resetting Filter Life:

After replacing your True HEPA Filter, place

the Pre-Filter back in and close the Front

Panel. While the unit is on, hold the Filter

Reset Button for at least 5 seconds until

you hear the beep. After the beep, the Filter

Replacement Indicator will disappear.

Your Winix True HEPA is now reset.

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Winix 6300-2 Air Purifier. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Winix. They might be able to provide an original manual. Are you looking for the manual of your Winix 6300-2 Air Purifier in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Winix Air Purifiers
More manuals of Air Purifiers

Frequently Asked Questions about Winix 6300-2 Air Purifier

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Winix WACU450 Air Purifier

Manual

Winix C545 Air Purifier

Manual

Winix 5500-2 Air Purifier

Manual

Winix AUS-1050AZBU Air Purifier

Manual

Winix XLC Air Purifier

Manual

Winix HR900 Air Purifier

Manual

Winix AUS-1250AZPU Air Purifier

Manual

Winix WACU300 Air Purifier

Related categories