Home > Household appliances > Air Purifiers > Winix Air Purifiers > Winix XLC Air Purifier

Manual Winix XLC Air Purifier

Need a manual for your Winix XLC Air Purifier? Below you can view and download the PDF manual for free in English. This product currently has 1 frequently asked question, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

WHERE TO USE

12~18 in

Allow 12 ~ 18 in. of space between TVs, radios, and

other electronics

Electromagnetic interference from certain electronics

may cause product malfunction.

Place indoors away from direct sunlight

Direct exposure may cause product malfunction or

failure.

Only place on hard, flat surfaces

Flimsy or slanted surfaces may result in abnormal

noise and vibrations.

Allow at least 12 ~ 18 in. from walls for maximum air

flow

True HEPA Filter

PlasmaWave

Washable AOC™

Carbon Filter

Pre-Filter

4-STAGE AIR PURIFICATION

(2) Pre-Filter

(2) Washable AOC™

Carbon Filter

(2) True HEPA Filters

Side Vent

Unit

User

Manual

Grill

Rear Panel

Front Panel

Button Control

Section

Alexa Setup

Guide /

Wi-Fi Setup

Guide

MODEL PART DIAGRAM

01. Auto Mode Indicator

The LED "Auto" light will indicate when Auto Mode is

activated.

02. Fan Speed Indicator

Indicates the current fan speed.

03. Sleep Mode Indicator

When Sleep Mode is activated, the Air Quality

Indicator LED light is disabled.

Fan speed will automatically set to minimum

speed(lower than 'Low') which will be nearly silent.

When Sleep Mode is active, Plasmawave

will be

disabled, but it can be turned back on.

04. Air Quality Indicator

Color coded LED light indicates one of four levels of

Air Quality: Red (poor), Amber (fair), Green (average),

and Blue (good).

05. PlasmaWave

Indicator

Indicates whether PlasmaWave

is enabled or

disabled.

06. Wi-Fi Indicator

• Enables or disables the Wi-Fi feature.

• When in the pairing state, the Wi-Fi LED flashes.

07. Filter Replacement Indicator

LED light indicates when it is time to change the filter.

08. Light Sensor

Detects the amount of ambient light in the

environment. When in Auto Mode, the Light Sensor

detects when to put the unit into Sleep Mode.

09. Power Button

Turns the unit on or off. During the first 30 seconds

of powering up, the Air Quality Indicator will cycle

through Blue, Green, Amber, and Red colors.

• Smart Sensor takes approximately 4 minutes to

detect the air quality in the environment before

normal operation begins.

10. Mode Button

Press to cycle through to set the mode of operation

(Auto, Sleep). The unit will default to Auto with

PlasmaWave

enabled when first powered on.

• Auto Mode automatically adjusts fan speeds

according to your indoor air quality. The fan speed

will adjust to low when air quality is good, medium

when fair, and to high when poor.

11. Sleep Mode Button

When Sleep Mode is activated, the Air Quality

Indicator LED light is disabled.

• Fan speed will automatically set to minimum

speed (lower than 'Low') which will be nearly

silent.

• When Sleep Mode is active, PlasmaWave

will be

disabled, but it can be turned back on.

12. Plasmawave

Button

Press the Plasmawave

button when the unit is

on to enable or disable this feature. By default,

Plasmawave

is enabled whenever the unit is

powered on.

"When the unit is running, you may hear a chirping

or buzzing sound. The sound is from large particles

passing through Plasmawave

, it is normal and does

not signify product failure."

13. Wi-Fi Button

• Press for 3 seconds to activate pairing mode.

• When Wi-Fi is paired, press the button to turn Wi-

Fi off or back on.

14. Filter Reset Button

After replacing the True HEPA Filter, use a small

object such as a clip, to press and hold the Filter

Reset Button for at least 5 seconds until the Filter

Replacement Indicator turns off.

CONTROL PANEL

INITIAL OPERATION

1. Remove the front/rear panel by grasping

its upper edge and gently pulling forward.

- To remove the front/rear panel, release

the latch at the lower edge of the panel.

2. Remove the Pre-Filter, then the plastic

bag of filters behind it.

3. Remove filters from protective plastic bag.

4. Install the filters until they fit securely in

place.

03. True HEPA Filter (back)

02. Washable AOC™ Carbon Filter (middle)

01. Pre-Filter (front)

5. After filters are installed, close the front panel.

6. Insert the power cord into an electrical

outlet.

Latch

When to Replace Filters

Filter Indicator Light When to Service When to Replace

Pre-Filter none

Clean once every 14 days

Permanent

Washable AOC™

Carbon Filter

none

Clean once every 3 months

Lasts Approx. 12 months

True HEPA Filter

Can NOT be WASHED

• When the Check Filter Indicator LED is on, it is time to replace the True HEPA Filter and Washable

AOC™ Carbon Filter.

• Intervals between filter replacement may vary depending on environment.

Filter performance may decrease after each wash and depending on contamination level prior to washing.

MAINTENANCE

CLEANING CARE

Cleaning the Filters:

Use a vacuum cleaner or soft brush to clean the

Pre-Filter

• If it is excessively soiled, rinse in room

temperature water.

• Do not use detergent or soap.

• Allow the filter to dry for 24 hours or more

before using.

• Intervals between filter cleaning may

vary depending on the air quality in the

environment.

To clean the Washable AOC™ Carbon Filter,

remove from the unit and rinse under lightly

running room temperature water.

• Do not use detergent or soap.

• Allow the filter to dry for 24 hours or mote

before using.

• Do not use hot water over 104ºF.

Cleaning the Exterior & Interior:

Wipe with a soft damp cloth using room

temperature water.

• Afterwards, wipe it down with a clean, dry

cloth. Open the front panel and clean the

interior with a vacuum cleaner.

• For optimal performance, clean every 1 - 2

months.

NOTICE

• When cleaning the unit, always unplug the

power cord first and then wait until the unit has

cooled down.

• Never disassemble, repair, or modify the unit

yourself.

• Do not use flammable sprays or liquid detergents.

• Do not allow children to clean or maintain the unit.

• Before cleaning or maintaining, ensure unit is

unplugged.

• Do not use benzene, alcohol, or other

volatile fluids, which may cause damage or

discoloration.

SPECIFICATIONS

Model XLC

Voltage AC120V / 60Hz

Power Rate 90W

Verified

Room Size

620sq.ft.

Dimensions

14.6in(W) × 14.6in(D)

× 30.6in(H)

Weight 30.6lbs

Replacement

Filter

Filter X2 / SKU: 1712-0089-03

The exterior, design, and product specifications

may be changed without prior notice to improve

product performance.

Resetting Filter Life:

After replacing your True HEPA Filter, place the Pre-Filter back in and close the Front Panel. While

the unit is on, use a small, thin object (such as a paperclip) to hold the Filter Reset Button for

at least 5 seconds until you hear the beep. After the beep, the Filter Replacement Indicator will

disappear. Your Winix True HEPA is now reset.

REPLACING FILTERS

• Dedicated Call Center:

☎

(877) 699-4649

• Website: www.winixamerica.com

Contact Winix for

product related inquiries and

customer service

To expedite service, please specify the model

name and number, the nature of the problem, your

contact information, and your address.

Air Purification means it

removes inanimate particles

Rating

Let us know what you think about the Winix XLC Air Purifier by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Winix XLC Air Purifier?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Winix XLC Air Purifier. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Winix XLC Air Purifier. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Winix. They might be able to provide an original manual. Are you looking for the manual of your Winix XLC Air Purifier in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand	Winix
Model	XLC
Category	Air Purifiers
File type	PDF
File size	1.98 MB

All manuals for Winix Air Purifiers
More manuals of Air Purifiers

Frequently Asked Questions about Winix XLC Air Purifier

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Does an air purifier also remove regular dust from the air? Verified

Yes, air purifiers also remove dust from the air that otherwise would need to be removed by dusting and cleaning. It depends on the air purifier up to what size of dust can be removed from the air.

This was helpful (158) Read more