Home > Home & Decoration > Lamps > Kichler Lamps > Kichler 15784CBR Small Lamp

Manual Kichler 15784CBR Small Lamp

Need a manual for your Kichler 15784CBR Small Lamp? Below you can view and download the PDF manual for free in English. This product currently has 7 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

SAFETY INSTRUCTIONS

READ THIS FIRST

KEEP THESE INSTRUCTIONS

CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel or main

fusebox before starting and during the installation.

This xture is intended for installation in accordance with the

National Electric Code (NEC) and Local code specications. Failure

to adhere to these codes and instructions may result in serious

injury and/or property damage and will void the warranty. If you are

not familiar with code requirements, installation by a certied

electrician is recommended.

1) WARNING: This xture is not to be installed within 10 feet (3M)

of a pool, spa or fountain.

2) This xture is to be used only with a power unit (transformer)

rated a maximum of 300 W (25 AMPS) 15 volts.

3) The #18 ga. xture wire is not intended for direct burial.

4) Direct burial rated wire is to be buried a minimum of 6"

(152mm) beneath the surface of the ground.

NOTE: If additional Direct Burial wire is needed, contact your

local Kichler

landscape distributor.

• 8 GA wire can be purchased in length of 250’ (76 M),

15503-BK.

• 10 GA wire can be purchased in length of 250’ (76 M),

15504-BK.

• 12 GA wire can be purchased in lengths of 100’ (30 M),

15501-BK; 250’ (76 M), 15502-BK; 500’ (152M), 15505-BK;

and 1000’ (304 M), 15506-BK.

5) Fixture shall not use a tungsten halogen lamp unless the

xture is marked for use with such lamps.

6) Wiring connections must be made with approved/listed wire

connection device(s) suitable for the application. Do not

exceed manufacturers’ wiring combination specications for

size and quantity of conductors.

ASSEMBLY AND INSTALLATION

1) Determine desired location for mounting xture.

2) Un-assemble mounting bracket by un-screwing the retaining studs.

3) Use mounting bracket as a template, mark position for mounting

screws and wireway hole (if desired).

4) Drill 3/32" (2 mm) pilot holes in mounting surface at position

marked for mounting screws. If using a wireway hole, drill 1/4"

(6mm) through mounting surface at position marked.

5) Mount the mounting bracket to mounting surface using provided

screws.

6) Pass supply wire through wireway in mounting bracket and

mounting surface. Wire may alternately be routed along the

mounting surface by routing the wire through the notch at the

bottom of the main body.

7) Install the main body to the mounting bracket with the retaining

studs.

8) Un-install the canopy and insert recommended bulbs.

9) Re-Install the canopy.

10) Make wire connections using supplied twist-on wire connectors

following instructions on bag.

INSTRUCCIONES DE SEGURIDAD

PRIMERO LEA ESTO

GUARDE ESTAS INSTRUCCIONES

PRECAUCIÓN – RIESGO DE DESCARGA ELÉCTRICA –

Desconecte la electricidad en el panel principal del interruptor

automático o caja principal de fusibles antes de comenzar y

durante la instalación.

Este artefacto se debe instalar de acuerdo con el Código Eléctrico

Nacional (NEC, por sus siglas en inglés) y con las especicaciones

del código local. No cumplir con estos códigos e instrucciones

puede resultar en lesiones graves y/ o en daños a la propiedad y

anulará la garantía. Si no está familiarizado con los requisitos del

código, la instalación se recomienda un electricista certicado.

ADVERTENCIA: Este artefacto no debe instalarse a

menos de 10 pies (3 m) de una piscina (alberca), spa o fuente.

2) Este artefacto debe utilizarse solamente con una unidad de

potencia (tranformador) con capacidad nominal máxima de

300 vatios (25 amp.) 15 voltios.

3) El alambre del artefacto calibre No. 18 no es para soterrado

directo.

4) El alambre clasicado para soterrado directo se debe enterrar

un mínimo de 6 pulgadas (152 mm) debajo de la supercie del

terreno.

NOTA: Si necesita alambre de soterrado directo adicional, co

muníquese con su distribuidor local Kichler® de productos de

jardinería ornamental.

For warranty information please visit: kichler.com/customer-care/warranty-information/landscape-warranty

Para informacion de la garantia por favor visite: kichler.com/customer-care/warranty-information/landscape-warranty

IS-15783-US

MOUNTING SCREW

TORNILLO DE MONTAJE

MOUNTING BRACKET

MÉNSULA DE MONTAJE

RETAINING STUD

PERNO DE RETENCIÓN

MAIN BODY

CUERPO PRINCIPAL

CANOPY

ESCUDETE

• El alambre calibre 8 puede comprarse en longitud de 250’

(76 m.), 15503-BK

• El alambre calibre 10 puede comprarse en longitud de 250’

(76 m.), 15504-BK

• El alambre calibre 12 puede comprarse en longitudes de 75’

(22 m.), 15550-BK; 100’ (30 m.), 15501-BK; 250’ (76 m.),

15502-BK; 500’ (152 m.), 15505-BK; y 1000’ (304 m.),

15506-BK.

5) El artefacto no debe utilizarse con lámparas de halógeno, a

menoss que el artefacto esté marcado para usar con tales

lámparas.

6) Las conexiones de cableado se deben hacer con las conexiones

del(los) dispositivos) de conexión de cableado aprobados/ de

la lista, adecuados para la aplicación. No exceda las especi

caciones de combinación de cableado del fabricante para el

tamaño y cantidad de conductores.

MONTAJE E INSTALACIÓN

1) Determine el lugar deseado para el montaje del artefacto.

2) Desarme la ménsula de montaje desenroscando los pernos de

retención.

3) Utilizando la ménsula de montaje como plantilla, marque la

posición de los tornillos de montaje y el agujero del canal de

alambres (si desea).

4) Perfore los agujeros piloto de 3/32" (2 mm.) en la supercie de

montaje marcada para los tornillos de montaje. Si usa el agujero del

canal de alambres, perfore 1/4" (6 mm.) a través de la supercie

de montaje en la posición marcada.

5) Monte la ménsula de montaje a la supercie de montaje

usando los tornillos que se proporcionan.

6) Pase el alambre de alimentación a través del canal de alambres

en la ménsula de montaje y supercie de montaje.

Alternativamente, el alambre puede ser encaminado a lo largo

de la supercie de montaje encaminando el alambre a través

de la ranura en la parte inferior del cuerpo principal.

7) Instale el cuerpo principal en la ménsula de montaje con los

pernos de retención.

8) Desinstale el escudete e inserte las bombillas recomendadas.

9) Reinstale el escudete.

10) Haga las conexiones de cableado usando las tuercas para

cables suministrados siguiendo las instrucciones de la bolsa.

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

Estamos aquí para ayudarle 866-558-5706

Horario: Lunes-Viernes 9am a 5pm EST (hora ocial del este)

Rating

Let us know what you think about the Kichler 15784CBR Small Lamp by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Kichler 15784CBR Small Lamp?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Kichler 15784CBR Small Lamp. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Kichler 15784CBR Small Lamp. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Kichler. They might be able to provide an original manual. Are you looking for the manual of your Kichler 15784CBR Small Lamp in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand	Kichler
Model	15784CBR Small
Category	Lamps
File type	PDF
File size	0.24 MB

All manuals for Kichler Lamps
More manuals of Lamps

Frequently Asked Questions about Kichler 15784CBR Small Lamp

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Is all LED lighting dimmable? Verified

No, not all LED lights are dimmable. This is indicated on the packaging or the light itself.

This was helpful (495) Read more

I put a new light in my lamp but it won't turn on, why is that? Verified

Some lamps are made for light sources of a specific wattage. When a light source is inserted that requires a higher wattage than the lamp can provide, the light may not turn on. If the lamp delivers a much higher wattage than what the light source is made for, the light source can burn out.

This was helpful (355) Read more

Why is the colour of light important? Verified

There generally are two kinds of light, warm light and cold light. Cold light keeps you sharp and awake. Warm light has a relaxing effect. The warmth of the light is measured in Kelvin and is indicated on the packaging of the lamp itself.

This was helpful (288) Read more

What is lumen? Verified

Lumen is a measuring unit for the total amount of visible light emitted by a source.

This was helpful (228) Read more

What screw bases exist? Verified

Worldwide there many types of sockets, but most used are those based on the Edison screw, indicated with the letter E. In most countries screw bases E27 and E14 are standard. In the United States E26, E17, E12 and E10 are standard.

This was helpful (172) Read more

What do watts say about my lamp? Verified

Watt is a measuring unit for electricity consumption. Lamps that produce more light, generally use more Watt, but for comparing light output you should always use lumen.

This was helpful (149) Read more