Home > Home & Decoration > Lamps > Kichler Lamps > Kichler 15268AZ Small Lamp

Manual Kichler 15268AZ Small Lamp

Need a manual for your Kichler 15268AZ Small Lamp? Below you can view and download the PDF manual for free in English. This product currently has 7 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page

Para informacion de la garantia por favor visite: www.landscapelighting.com/portal/warranty_page

SAFETY INSTRUCTIONS

READ THIS FIRST

KEEP THESE INSTRUCTIONS

This xture is intended for installation in accordance with the National

Electric Code (NEC) and Local Code specications. Failure to adhere to

these codes and instructions may result in serious injury and/or property

damage and will void the warranty.

1) WARNING: This xture is not to be installed within 10 feet (3M) of a pool,

spa or fountain.

2) According to the requirements of the National Electric Code (NEC), direct

burial rated wire is to be buried a minimum of 24” [152mm] beneath the

surface of the ground. Conductors in rigid metal conduit or intermediate

metal conduit must be buried a minimum of 6”. Conductors in nonmetallic

raceways must be buried a minimum of 18”.

3) This xture shall use an incandescent or tungsten halogen 75 watt maximum

PAR20, PAR30, or PAR30LN type lamp only.

CAUTION

ELECTRICAL POWER MUST BE TURNED OFF DURING INSTALLATION OR MAINTENANCE.

WHEN INSTALLING KICHLER

LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE),

CARE SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS.

WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES, GRASS

CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED ON THE LIGHT BULB, LENS,

OR BODY OF THE FIXTURE.

ASSEMBLY AND INSTALLATION

1) Determine desired location for fixture and dig hole. Hole should be

approximately 8” (203mm) in diameter and 13” (330mm) deep.

2) Run conduit or direct burial cable to the hole.

3) Attach the conduit or direct burial cable to the bottom of the housing. Use

only liquid-tight type ttings to prevent the entry of ground water into the

xture. Fitting threads must be sealed using an appropriate sealant.

4) Fill bottom of hole with approximately 3” (76mm) of pea gravel.

5) Place xture in hole and backll around the xture with soil.

6) Remove screws from top of xture and remove cap and lens.

7) Unplug the yoke assembly and remove from the xture.

8) Remove screws from wireway cover and remove wireway cover.

9) Run suitable supply conductors through conduit into wireway compartment.

10) Using suitable wire connectors, join the incoming conductors to the wire

leads on the bottom of the wireway cover.

11) Using the sealant included with the xture seal all unused conduit openings

and the wire entry point in the housing bottom interior. Instructions for mixing

the sealant are included on the sealant envelope.

12) Re-install the wireway cover and secure with screws.

13) Plug yoke assembly wiring harness into the receptacle on the wireway

cover.

14) Insert yoke assembly with into xture. The gasket around top of yoke

assembly should be inspected to insure it is clean and free of debris.

15) Install a proper lamp and adjust angle if desired.

16) Place lens and cap on top of xture and secure with screws.

INSTRUCCIONES DE SEGURIDAD

Primero lea esto

Guarde estas instrucciones

Este artefacto se debe instalar de acuerdo con el Código Eléctrico Nacio-

nal (NEC, por sus siglas en inglés) y con las especicaciones del código

local. No cumplir con estos códigos e instrucciones puede resultar en

lesiones graves y/ o en daños a la propiedad y anulará la garantía.

1) ADVERTENCIAERTENCIA: Este artefacto no debe instalarse a menos de

10 pies (3 m) de una piscina (alberca), spa o fuente.

2) De acuerdo con los requisitos del Código Eléctrico Nacional (NEC), el

alambre con capacidad nominal de soterrado directo se debe soterrar un

mínimo de 24” [610mm] debajo de la supercie del terreno. Los

conductores de conducto metálico rígido o conductores metálicos

intermedios se deben soterrar un mínimo de 6”. Los conductores en

conductos para tuberías se deben soterrar un mínimo de 18”.

3) Este artefacto debe utilizar solamente una lámpara tipo halógeno de

tungsteno de 75 vatios, máximo, PAR20, PAR30 o PAR30LN o lámpara

incandescente.

MONTAJE E INSTALACIÓN

1) Determine el lugar deseado para el artefacto y cave el hoyo. El hoyo debe

tener aproximadamente 8” (203 mm) de diámetro y 13” (330 mm) de

profundidad.

2) Corra el conducto o el cable de soterrado directo al hoyo.

3) Acople el conducto o el cable de soterrado directo a la parte inferior de

la cubierta. Use solamente accesorios estancos a los líquidos para impedir

la entrada del agua subterránea al artefacto. Las roscas del artefacto se

deben sellar utilizando un compuesto sellante apropiado.

4) Llene el fondo del agujero con aproximadamente 3” (76mm) de grava de

tamaño pequeño.

5) Coloque el artefacto en el hoyo y rellene alrededor del artefacto con tierra.

6) Quite los tornillos de la parte superior del artefacto y quite la tapa y la

lente.

Date Issued: 12/2/11 IS-15268-US

7) Desenchufe el conjunto de la horquilla y quite del artefacto.

8) Quite los tornillos de la tapa del canal de alambres y quite la tapa del

canal de alambres.

9) Corra los conductores de alimentación eléctrica adecuados a través del

conducto en el compartimiento del canal de alambres.

10) Utilizando conectores de alambre adecuados, una los conductores de

llegada a los hilos terminales en la parte inferior de la tapa del canal de

alambres.

11) Utilizando el compuesto sellante que se incluye con el artefacto selle

todas las aberturas de conducto no utilizados y el punto de entrada del

alambre en el interior del fondo de la cubierta. Las instrucciones para

mezclar el compuesto sellante se incluyen en el sobre del mismo.

12) Vuelva a instalar la tapa del canal de alambres y sujete con los tornillos.

13) Enchufe el arnés del cableado del conjunto de la horquilla en el

receptáculo en la tapa el canal de alambres.

14) Inserte el conjunto de la horquilla en el artefacto. La empaquetadura

alrededor de la parte superior del conjunto de la horquilla se debe

inspeccionar para estar seguro de que esté limpia y sin escombros.

15) Instale una lámpara apropiada y ajuste el ángulo si desea.

16) Coloque la lente y la tapa en la parte superior del artefacto y sujete con

los tornillos.

SCREW

TORNILLO

CAP

TAPA

LENS

LENTE

LAMP

LÁMPARA

YOKE ASSEMBLY

CONJUNTO DE LA

HORQUILLA

GASKET

EMPAQUETADURA

WIREWAY COVER

TAPA EL CANAL

DE ALAMBRES

SCREW

TORNILLO

RECEPTACLE

RECEPTÁCULO

HOUSING

CUBIERTA

Rating

Let us know what you think about the Kichler 15268AZ Small Lamp by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Kichler 15268AZ Small Lamp?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Kichler 15268AZ Small Lamp. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Kichler 15268AZ Small Lamp. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Kichler. They might be able to provide an original manual. Are you looking for the manual of your Kichler 15268AZ Small Lamp in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand	Kichler
Model	15268AZ Small
Category	Lamps
File type	PDF
File size	0.24 MB

All manuals for Kichler Lamps
More manuals of Lamps

Frequently Asked Questions about Kichler 15268AZ Small Lamp

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Is all LED lighting dimmable? Verified

No, not all LED lights are dimmable. This is indicated on the packaging or the light itself.

This was helpful (493) Read more

I put a new light in my lamp but it won't turn on, why is that? Verified

Some lamps are made for light sources of a specific wattage. When a light source is inserted that requires a higher wattage than the lamp can provide, the light may not turn on. If the lamp delivers a much higher wattage than what the light source is made for, the light source can burn out.

This was helpful (351) Read more

Why is the colour of light important? Verified

There generally are two kinds of light, warm light and cold light. Cold light keeps you sharp and awake. Warm light has a relaxing effect. The warmth of the light is measured in Kelvin and is indicated on the packaging of the lamp itself.

This was helpful (285) Read more

What is lumen? Verified

Lumen is a measuring unit for the total amount of visible light emitted by a source.

This was helpful (228) Read more

What screw bases exist? Verified

Worldwide there many types of sockets, but most used are those based on the Edison screw, indicated with the letter E. In most countries screw bases E27 and E14 are standard. In the United States E26, E17, E12 and E10 are standard.

This was helpful (172) Read more

What do watts say about my lamp? Verified

Watt is a measuring unit for electricity consumption. Lamps that produce more light, generally use more Watt, but for comparing light output you should always use lumen.

This was helpful (148) Read more