Manual Westinghouse WFE612SC Range

Manual

6 7INSTALLATIONINSTALLATION

Cabinet requirements

This appliance has been designed to ‘slot-in’ to a 600mm

wide gap built-in standard kitchen cabinets. As such the

appliance can be installed to suit the height of the benches

This allows the cooker to integrate well into contemporary

kitchens. The cooker may also be installed at the end of

a line of benches or with a free space on either side.

• Electric hob models must not be installed in a corner;

they must be installed at least 100mm from the

side wall. Gas hob models must be installed with a

minimum clearance of 100mm to side walls made

of unprotected combustible materials.

• For gas models refer to section 6.10.1 in AS/NZS

5601.1 for all relevant clearances.

WARNING

WARNING

This appliance has been tested and approved to the

relevant Australian Standards. It is designed to cook

food, it will get hot. Cabinet materials must be capable

of withstanding 85

o

C. Installation into lower temperature

tolerant cabinetry (e.g. vinyl coated) may result in

deterioration of the low temperature coating by discolour

or bubbling.

Electrolux Home Products cannot accept responsibility

for damage caused by installation into low temperature

tolerant cabinets.

Installation and service warning

WARNING

WARNING

• Only an authorised person must install and

service this appliance (Certificate of Compliance

to be retained).

• In order to avoid a hazard, the installation

instructions MUST be followed.

• In order to avoid the appliance tipping, the anti-tilt

plate MUST be installed.

• Appliances requiring connection to 230 – 240V

MUST be earthed.

• An authorised person should inspect this appliance

every 5 years.

• This appliance must NOT be installed on a base,

box or in a closed cupboard.

• If the electrical supply cord is damaged, a qualified

person MUST replace the cord to avoid a hazard or

void your warranty.

• The unit must be pushed up against the wall on

installation. On gas units check that the gas hose,

if used, has not been kinked during installation.

INSTALLING THE APPLIANCE

(600mm wide product)

Recommended cabinet design

630mm

600mm

Clearance to side wall

(refer notes)

600mm

minimum

anti-tilt plate

720mm (NOM)

900mm (NOM)

910mm minimum

596mm minimum

1.25m electrical

service cord (if fitted)

Preparing for installation

1. Check that the required services are correctly

positioned (see electrical and gas services

requirements section and cabinet requirements

section).

2. Ensure that cabinetry has correct details (see cabinet

requirements section).

3. Unpack the cooker.

4. Remove the foam pack containing accessories.

5. Remove the internal pack from the oven and position

shelf supports and grill trays.

6. Remove the 2 screws for the splashback from the

rear panel, and fit it to the unit with the same screws.

Following table outlines the distance between the floor

supporting the product and the surface supporting

cooking vessel:

Surface type

(supporting vessel)

Distance (mm)

Ceramic Glass 910

Solid Hotplates 920

Cast Trivets 933

Fitting the anti-tilt plate & stabilising bolt

Cooker Stability

NOTE: To ensure cooker stability, both the anti-tilt plate

and stability bolt MUST be installed on all cookers

(electric and gas).

Installation Sequence

1. The cooker is delivered with the anti-tilt plate. Locate

the anti-tilt plate against the rear wall. If locating

between 2 cupboards, then fit the plate in the centre

of the space. If locating the cooker at the end of a

cupboard, then position the side of the plate 48mm

from the cupboard.

NOTE: If cooker cannot be located against rear

wall, move anti-tilt plate forward to suit.

2. Securely fix the anti-tilt plate to the floor with

appropriate fasteners.

3. Slide the cooker back into the anti-tilt plate so that

rear cover rests against the rear wall.

Then check the height and level of the cooker.

If required, pull the cooker back out and adjust the

levelling feet as required.

4. Cut the cable tie from the stability bolt.

5. Rotate the stability bolt 180 clockwise until it is

pointing to the left like the picture below.

6. The stability bolt should now be able to drop to

the floor.

7. Mark the position for the stability bolt on the floor.

8. Pull the cooker out and drill the bolt hole, using a

6.5mm masonry or wood drill. Minimum 30mm deep

for concrete.

9. Reposition the cooker back into place, then fit the

stability bolt into the drilled hole.

10. Connect gas and electricity supply (refer to

pages following).

11. Fit the kick panel onto the cooker.

48mm to side

of plate

5mm clearance

Rear cover

Anti-tilt

plate

Rear adjustable foot

Stability bolt

Kick panel

ø6.5mm drilled

location hole

Front adjustable feet

Installing splashback

Fit splashback to rear of hob with the two

screws provided

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Westinghouse WFE612SC Range. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Westinghouse. They might be able to provide an original manual. Are you looking for the manual of your Westinghouse WFE612SC Range in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Westinghouse Ranges
More manuals of Ranges

Frequently Asked Questions about Westinghouse WFE612SC Range

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Westinghouse WFE517 Range

Manual

Westinghouse WLG505WA Range

Manual

Westinghouse WFE9515SD Range

Manual

Westinghouse WFE904SD Range

Manual

Westinghouse WFE916SA Range

Manual

Westinghouse WFE646DSCB Range

Manual

Westinghouse WFE916DSD Range

Manual

Westinghouse WLG517WB Range

Related categories