Manual Teledex L2S-E Diamond Elite Phone

Manual

PROGRAMMING THE AUTO DIAL KEYS

Models L2S-10E, L2-10E, L2S-5E, and L2-5E include programmable auto dial keys.

The L2S-10E and L2-10E models each have ten (10) programmable auto dial keys, and

the L2S-5E and L2-5E models each have five (5) programmable auto dial keys. These keys

can be programmed to automatically dial telephone numbers or activate telephone system

features.

To program the auto dial keys, the telephone must be connected to a telephone line.

1) Lift the handset or press the

SPEAKERPHONE key (models L2S-5E and L2S-10E.)

2) Press the recessed

STORE key and release (Please see phone diagram for key location).

3) Enter the telephone number, including pause (see below) as required. The sequence

can be up to 15 digits in length.

4) Press the auto dial key where the number is to be stored.

5) Hang up the handset or press the

SPEAKERPHONE (models L2S-5E, L2S-10E only)

key to disconnect.

PAUSE KEY

The PAUSE key can be used to provide a timed pause between dialed digits within an auto

dial key. The timing of the pause is programmable, with the factory default set to zero (0)

seconds. To change the pause timing:

1) Lift the handset or press the

SPEAKERPHONE key (models L2S-5E and L2S-10E.)

2) Press the

STORE key (see diagram on inside front cover for key location.)

3) Press the PAUSE key (see diagram for key location.)

4) Press 0 - 5 on the DTMF pad. The number selected will be the pause timing in seconds

(ie: pressing the ‘3’key will insert a 3-second pause, etc.)

5) Press the

STORE key. The selected pause is now inserted into the dialing string.

FLASH KEY

The FLASH key, when programmed behind an auto dial key, provides a timed line

interrupt typically used for accessing PBX/CO features such as transfer or conference. The

timing of the hookflash is programmable, with the factory default set to 600 milliseconds.

Some PBXs may require you to change the hookflash timing from this default. To change

the hookflash timing:

1) Lift the handset or press the

SPEAKERPHONE key (models L2S-5E and L2S-10E.)

2) Press the

STORE key (see diagram on inside front cover for key location.)

3) Press the FLASH key (see diagram for key location.)

4) Select 1 - 9 on the DTMF pad. The number selected will be the new flash timing in

hundreds of milliseconds (ie: pressing the ‘3’key will reset the flash to 300 ms, etc.)

5) Press the

STORE key. The selected flash timing is now programmed.

CONVERTING FROM DESK TO WALL MOUNT

The Diamond Elite telephone can be converted for wall mounting applications. This

conversion process is easiest when the handset and line cords are not connected.

1) Located on the front of the telephone, above the speaker grill, is the wall/desk mounting

clip. Remove this clip by firmly pushing upward (towards the hook switch.)

2) Rotate the clip one half turn (180 degrees) so that the side with the protruding edge is

towards the top of the telephone and reinsert. This edge will hold the handset.

3) Turn the telephone over so the back side is up, facing you. Ensure that the telephone is

resting on a non-abrasive surface, to prevent scratching.

4) Locate and remove the mounting bracket, by firmly pushing back and pulling up to

disengage two of the four retaining tabs, and remove the bracket.

5) Rotate the mounting bracket one half turn (180 degrees) so that the mounting eyelet is

facing in the same direction as the other mounting eyelet located on the lower part of

the telephone.

6) Insert the top two retaining tabs of the mounting bracket into the slots located near the

middle of the telephone. Then firmly push down to insert the retaining tabs on the

opposite side of the mounting bracket.

7) Connect a short modular line cord into the jack on the back of the phone labeled

TO

TEL. Route the line cord throughout the line cord channel. Connect the other end of

line cord to the phone jack on the wall mounting plate.

8) Turn the telephone over, and slide it down onto the mounting posts. Both eyelets should

line up with the mounting posts.

9) Complete the process by installing the handset and handset cord.

4 5

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Teledex L2S-E Diamond Elite Phone. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Teledex. They might be able to provide an original manual. Are you looking for the manual of your Teledex L2S-E Diamond Elite Phone in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Teledex Phones
More manuals of Phones

Related products

Manual

Teledex L2-10E Diamond Elite Phone

Manual

Teledex A102 Phone

Manual

Teledex L2-E Diamond Elite Phone

Manual

Teledex A110 Phone

Manual

Teledex BTX3510 Phone

Manual

Teledex AT1102 Phone

Manual

Teledex BTX4700 Phone

Manual

Teledex A103 Phone

Related categories