8
Installation
– Scope of delivery: dryer, installation and operating instructions, woollens basket (depending on
model).
– Check dryer for transport damage.
– The dryer is very heavy. Do not attempt to lift it on your own.
– Be careful to avoid sharp edges.
– Do not set up in a room that is susceptible to frost. Freezing water may cause damage.
– If in doubt, have the appliance connected by a specialist.
– Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.
Setting up the dryer
– The appliance plug must always be accessible.
– Ensure that the appliance is installed on a clean, level
and firm surface.
– Do not obstruct the air inlet on the front of the dryer.
– Keep the area around the dryer clean.
– Make the dryer level using the threaded feet
and a spirit level.
– Do not remove the threaded feet under any
circumstances.
Mains connection see Safety instructions a page 13.
– Connect to an AC earthed socket. If in doubt have the
socket checked by a specialist.
– The mains voltage and the voltage shown on the rating
plate (a page 10) must be the same.
– The connected load and necessary fuse protection are
specified on the rating plate.
Frost protection / Transport
Frost protection - preparation
1. Empty the condensate container a page 4.
2. Select any programme using the programme selector.
3. Press the inicio/stop (start/stop) button a condensed water is pumped into the container.
4. Wait 5 minutes and then empty the condensate container again.
5. Turn the programme selector to (stop).
Transport
– Prepare the dryer a see Frost protection - preparation.
– Transport the dryer in a vertical upright position.
– Following transportation, do not use the dryer for two hours.
The dryer contains residual water;
this can flow out if the dryer is tilted.
Signal
Switching on/off an acoustic signal at the end of the programme
delicado](low heat) light on a"an acoustic signal at the end of the programme is switched on.
delicado](low heat) light off a an acoustic signal at the end of the programme is switched off.
1.
2.
Take all accessory parts out of the
drum. The drum must be empty.
Make sure that the air inlet
remains unobstructed
Clean and level
Do not set up the dryer behind a door or sliding door, as this may obstruct
the dryer door or prevent it from opening. This will prevent a potentially
fatal danger to children from locking themselves in.
1 x to the
right
Press and hold delicado (low heat)
and turn 3 x to the right
Press delicado (low heat)
to switch on/off the signal
Turn to
(stop)
Turn to
(stop)
Do not operate the dryer if
there is a danger of frost.
9
Care and cleaning
Heat exchanger
The dryer's heat exchanger is cleaned automatically during drying.
Do not pull out the condensate container during the cleaning process.
Dryer housing, control panel, air intake
Wipe with a soft, damp cloth.
Do not use harsh cleaning agents or solvents.
Remove detergent and cleaning agent residue immediately.
Filter in the condensate container
The filter is cleaned automatically when the condensate container is emptied.
However, the filter should still be cleaned regularly under running water a This prevents
stubborn deposits/dirt from building up.
1. Pull out the condensate container.
2. Pull the filter out of its snap-in lock.
3. Clean the filter under running water or in the dishwasher.
4. Refit the filter.
5. Insert the condensate container so that it locks into place.
Only operate the dryer with the filter inserted.
Moisture sensor
The dryer is equipped with stainless steel moisture sensors. Moisture sensors measure
how damp the laundry is. A thin layer of limescale may build up on the moisture sensors
after prolonged use.
1. Open the door.
2. Clean the moisture sensors using a damp sponge with a rough surface.
Do not use steel wool or abrasive materials.
Appliance must be switched off.
10
Technical Data
ʠ
Dimensions (DxWxH) 60 x 60 x 85 cm (height adjustable)
Weight
approx. 51 kg
Max. capacity
7 kg
Condensate container
4.0 l
Connection voltage
220-240 V
Connected load
1000 W
Fuse protection
10 A
Ambient temperature
5 - 35°C
Product number
Production number
Inside of door
The rating plate can be found on the back of the dryer.
Power consumption when switched off
0,10 W
Power consumption when ready for use (left-on mode)
1,00 W
ʠ
Drum interior light (depending on model): The drum lights up after the door is opened and after the programme starts, and switches off
automatically.
Consumption values table
Programme
Spin speed which
is used for spinning the
laundry
Duration** Energy consumption**
cottons 7 kg 3.5 kg 7 kg 3.5 kg
cupboard dry* 1400 rpm 151 min 93 min 1.33 kWh 0.80 kWh
1000 rpm 178 min 110 min 1.65 kWh 0.97 kWh
800 rpm 205 min 127 min 1.92 kWh 1.13 kWh
iron dry* 1400 rpm 110 min 71 min 0.94 kWh 0.61 kWh
1000 rpm 137 min 88 min 1.24 kWh 0.80 kWh
800 rpm 166 min 111 min 1.55 kWh 1.04 kWh
synthetics 3.5 kg 3.5 kg
cupboard dry* 800 rpm 64 min 0.54 kWh
600 rpm 78 min 0.68 kWh
* Programme setting for testing in accordance with the applicable EN61121 standard.
** The values may differ from those specified, depending on the type of fabric, composition of laundry to be dried, residual moisture in the fabric,
the degree of dryness that has been set, the amount of laundry being loaded and the environmental conditions.
Most efficient programme for cotton fabrics
The following "standard cottons programme" (identified with ) is suitable for drying normal, wet cotton laundry and is most efficient in terms of
its combined energy consumption for drying wet cotton laundry.
Standard programme for cottons in accordance with current EU regulation 932/2012
Programme Load Energy consumption Programme duration
cottons cupboard dry 7 kg/3.5 kg 1.65 kWh/0.97 kWh 178 min/110 min
Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU.
Optional accessories (order from the after-sales service using the order number, depending on the model)
Washer-dryer stack connection set
The dryer can be placed on top of a suitable washing machine with the same width and depth to save space. The dryer must be fastened
to the washing machine using this connection set. WZ 20400: with pull-out worktop.
Installation underneath the worktop
Instead of the appliance covering plate, you must have a metal cover fitted by a specialist.
Platform
For easier loading and unloading. The basket contained in the drawer can be used to carry the laundry.
Wollens basket
For drying individual wollen fabrics, sports shoes and soft toys (see separate instructions for “Woollens basket”).
WZ
11410
WZ
20290
WZ
20500
WZ
20600
11
Normal noises
During drying, the compressor and the pump generate some noise which is entirely normal.
The compressor in the dryer may
occasionally generate a humming noise.
The volume and pitch of this may vary
depending on the selected
programmes and the progress of the
drying.
The compressor in the dryer is ventilated
from time to time, which creates a whirring
sound.
The automatic cleaning process causes
a clicking noise.
The process of pumping the condensation
into the condensate container generates
pumping noises.
12
What to do if...
If you cannot rectify a fault yourself (e.g. switching off/on), please contact our after-sales service. We will
always find an appropriate solution and will avoid unnecessary visits by engineers. Trust the expertise of
the manufacturer and rest assured that the repair will be carried out by trained service technicians using
original spare parts. The contact details of your local after-sales service can be found in the enclosed after-
sales service directory, or by calling one of these numbers:
– GB 0344 892 8999 (Calls charged at local or mobile rate.)
– IE 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.)
When contacting the after-sales service, please quote the appliance's product number (E no.)
and production number (FD) (see under the loading door).
Turn the programme selector to (stop) and unplug the mains plug from the socket.
ʠ
The inicio/stop (start/stop)indicator
lamp does not light up.
Mains plug plugged in?
Programme selected? Check the socket fuse.
ʠ
The display panel light and indicator
lights (depending on model) go out
and the inicio/stop (start/stop)
indicator light flashes.
Energy-saving mode is activated a see the separate
Energy-saving mode instructions.
ʠ
The Ílimp. (container) indicator
lamp and the inicio/stop (start/stop)
button are flashing.
Empty the condensate container a page 4.
Clean the condensate container filter if necessary a page 9.
Dryer transported? a Wait 2 hours and start again.
ʠ
The x limp. (filter) indicator lamp and
inicio/stop (start/stop) button are
flashing.
Rinse the fluff filter under running water a page 4.
ʠ
Dryer does not start. inicio/stop (start/stop) button selected?
Door closed?
Ambient temperature greater than 5°C? The optimum ambient
temperature for drying is between 5 °C and 35 °C.
ʠ
Water is leaking out. Make sure the dryer is level.
ʠ
The door opens by itself. Push the door closed until you hear it click into place.
ʠ
Creasing. Laundry load exceeded?
Remove articles of clothing immediately after the end of the
programme, hang up and pull into shape.
Unsuitable programme selected a page 7.
ʠ
Laundry is not dried correctly or is still
too damp.
After the end of the programme, warm laundry feels damper than it
actually is. Spread the laundry out and allow the heat to disperse.
Finely adjust the dryness level – this extends the drying time but
does not increase the temperature. Your laundry will become drier.
Select a programme with a longer drying time or increase the
drying level. This does not increase the temperature.
Select a timed programme for subsequent drying of laundry that is
still damp.
If you have exceeded the maximum load for the programme, the
laundry may not be dried properly.
Clean the moisture sensor in the drum. A fine layer of limescale
may adversely affect the performance of the sensors and your
washing will not dry properly.
Drying has been interrupted as a result of a power cut, because
the condensation container is full or because the maximum drying
time has been exceeded.
ʠ
Drying time too long. Rinse the fluff filters under running water a page 4.
Insufficient supply of air a ensure that air can circulate.
Air inlet possibly blocked a Clear inlet a page 8.
Ambient temperature higher than 35 °C a ventilate the room. The
optimum ambient temperature for drying is between 5 °C and 35
°C. Outside of this range, the drying time may increase.
ʠ
The humidity in the room increases
significantly.
Make sure the room is sufficiently ventilated.
ʠ
Power failure. Remove laundry from the dryer immediately and spread out. This
allows the heat to dissipate. Be careful as the door, the drum and
the laundry may be hot.
ʠ
Other intermittent noises and
vibrations.
Not an error. Normal noises a page 11.
ʠ
Loud humming noise for several
seconds.
Has the condensate container been properly inserted? a Push the
condensate container all the way in.
Not an error. Normal noises a page 11.
13
Safety instructions
Emergency
– Pull the appliance plug out of the socket immediately or disconnect the fuse.
ONLY use the
dryer...
– in rooms inside the house.
– to dry fabrics.
The dryer
must
NEVER...
– be used for purposes other than those described above.
– be modified in terms of its technology or properties.
Hazards
– The dryer must not be used by children or persons who have not been instructed in
its use.
– Do not leave children unsupervised near the dryer.
– Keep pets away from the dryer.
– Remove all objects from pockets, and lighters in particular a Risk of explosion.
– Do not lean or sit on the door a Risk of tipping.
Installation
– Secure loose cables a Risk of tripping.
– Do not operate a dryer if there is a risk of frost.
Mains
connection
– Connect the dryer to an AC earthed socket according to specifications, otherwise it
cannot be guaranteed that the appliance is completely safe.
– The cable cross-section must be sufficient.
– Only use earth-leakage circuit breakers with the following symbol:
– The appliance plug and socket must be compatible.
– Do not use multiple plugs/connectors and/or extension cables.
– Do not touch or hold the appliance plug with wet hands a Risk of electric shock.
– Never pull the appliance plug out of the socket by its cable.
– Do not damage the mains lead a Risk of electric shock.
Operation
– Only load the drum with laundry. Check the contents before you switch the dryer on.
– Do not use the dryer if the laundry has been in contact with solvents, oil, wax, grease
or paint (e.g. hair styling products, nail varnish remover, stain remover, cleaning
solvent, etc.) a Risk of fire/explosion.
– The tumble dryer is not to be used if industrial chemicals have been used for
cleaning.
– Dust (e.g. coal dust, flour) poses a danger: Do not use the dryer
aRisk of explosion.
– Do not turn off the dryer until the drying process ends, unless the laundry will be
removed quickly and spread out, so that the heat can dissipate.
– Do not put laundry containing foamed material/rubber in the dryer a elastic material
may be destroyed and the dryer be damaged due to possible deformation of the
foamed material.
– When cleaning the fluff filter, make sure that no foreign material (down or filling
material) gets into the air duct opening. If necessary, clean the drum beforehand with
a vacuum cleaner. If foreign material should still get into the air duct a call the after-
sales service a Risk of fire/explosion.
– Light things, such as long hair, may be sucked into the air inlet of the dryer
aRisk of injury.
– Final part of a tumble dryer cycle occurs without heat (cool down cycle), to ensure
that the items are left at a temperature that ensures that the items will not be
damaged.
– Switch off the dryer once the programme has ended.
– The water from condensation is not drinking water and may be contaminated with
fluff.
Defect
– Do not use the dryer if it is defective or if you suspect that it is. Repairs must only be
carried out by the after-sales service.
– Do not use the dryer if the mains cable is defective. To avoid danger, only have the
defective mains cable replaced by the after-sales service.
Spare parts
– Only use genuine spare parts and accessories for safety reasons.
Disposal
– Pull out the appliance plug, then cut off the mains cable from the appliance.
Dispose of at a municipal waste disposal facility.
– The dryer's heat exchanger contains fluorinated greenhouse (R134a) gas in
a hermetically sealed unit a dispose of in a proper manner. Capacity: 0.220 kg.
Total GWP: 0.315 tCO
2
.
– Packaging: Keep all packaging out of reach of babies and children a Risk of
suffocation.
– All materials are environmentally sound and can be reused.
Dispose of in an environmentally-responsible manner.
siemens-home.com/welcome
Register
your
product
online
Dryer
WT44W101EE
en Instruction manual
Observe the safety instructions on page 13.
Read these instructions and the separate Energy-saving mode
instructions before switching on the dryer.
Join the conversation about this product
Here you can share what you think about the Siemens WT44W101EE Dryer. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.