Home > Home & Decoration > Lamps > Kichler Lamps > Kichler 9564LD Tournai Lamp

Manual Kichler 9564LD Tournai Lamp

Need a manual for your Kichler 9564LD Tournai Lamp? Below you can view and download the PDF manual for free in English. This product currently has 7 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

1) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work without

shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your home. Place

the main power switch in the “OFF” position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker switch(s),

that control the power to the ﬁxture or room that you are working on.

c) Place the wall switch in the “OFF” position. If the ﬁxture to be

replaced has a switch or pull chain, place those in the “OFF”

position.

2) Take threaded pipe from parts bag and screw in screw collar loop a minimum

of 6 mm (1/4”). Lock into place with hexnut.

3) Run another hexnut down threaded pipe almost touching ﬁrst hexnut.

Now screw threaded pipe into mounting strap. Mounting strap must be

positioned with extruded thread faced into outlet box. Threaded pipe must

protrude out the back of mounting strap. Connect mounting strap to outlet box.

4) Unscrew the threaded ring from screw collar loop. Take canopy and pass

over screw collar loop. Approximately one half of the screw collar loop exterior

threads should be exposed. Adjust screw collar loop by turning assembly

up or down in mounting strap. Remove canopy.

5) After desired position is found, tighten top hexnut up against the bottom of

the mounting strap.

6) Slip canopy over screw collar loop and thread on threaded ring. Attach

chain (with ﬁxture connected) to bottom of screw collar loop. Unscrew

threaded ring, let canopy and threaded ring slip down.

7) Weave electrical wire and ground wire through chain links no more than 3

inches apart. Pass wire through threaded ring, canopy, screw collar loop,

threaded pipe and into outlet box.

8) Connect ﬁxture ground wire to outlet box ground wire with wire connector.

(Not provided.) Never connect ground wire to black or white power

supply wire.

9) Make wire connections (connectors not provided). Reference chart below

for correct connections and wire accordingly.

10) Raise canopy to ceiling.

11) Secure canopy in place by tightening threaded ring onto screw collar loop.

12) Insert recommended bulb.

13) Raise cage up to ﬁxture, placing top of cage inside roof.

14) Thread ball studs into holes in side of roof and into cage. Tighten ball

studs to secure cage to roof.

1) COUPER L’ALIMENTATION SECTEUR.

IMPORTANT: TOUJOURS couper l’électricité avant de commencer le

travail.

a) Localiser le coffret à fusibles ou le disjoncteur du domicile. Mettre

l’interrupteur principal en position d’Arrêt.

b) Dévisser le ou les fusibles (ou mettre le disjoncteur sur Arrêt) qui

contrôlent l’alimentation vers le luminaire ou la pièce dans laquelle

le travail est effectué.

c) Mettre l’interrupteur mural en position d’Arrêt. Si le luminaire à

remplacer est doté d’un interrupteur ou d’une chaîne connectée à

l‘interrupteur, placer ces éléments en position d’Arrêt.

2) Visser le tube ﬁleté (qui se trouve avec les pièces détachées) dans le

collier-écrou, sur une longueur minimum de 6 mm (1/4 po). Fixer avec

un écrou hexagonal.

3) Visser un second écrou hexagonal de manière à ce qu’il touche presque

le premier. Visser ensuite le tube ﬁleté sur la patte de ﬁxation, en le

faisant dépasser et en dirigeant la partie ﬁletée des vis vers la boîte de

jonction. Connecter la patte de ﬁxation à la boîte de jonction.

4) Dévisser la bague ﬁletée du collier-écrou. Passer le cache sur le collier-

écrou. Environ la moitié de ﬁletage extérieur de celui-ci doit être apparent.

Fixer le collier-écrou en faisant pivoter l’assemblage vers le haut ou vers

le bas. Enlever le cache.

5) La bonne position étant trouvée, serrer l’écrou hexagonal supérieur

contre le partie inférieur de la patte de ﬁxation.

6) Glisser le cache sur le collier-écrou et enﬁler sur la bague ﬁletée. Attacher

la chaine (avec l’assemblage connecté) au bas du collier-écrou. Dévisser

la bague ﬁletée et laisser glisser le cache et la bague ﬁletée.

7) Entrelacer le ﬁl électrque et le ﬁl de mise á la terre et faire passer le tout

dans les anneaux de la chaîne en espaçant au maximum de 3 po.

Passer le ﬁl dans la bague ﬁletée, le cache, le collier-écrou, le tube ﬁleté

et la boîte de jonction.

8) Avec l’attache-ﬁl (qui n’est pas fourni), connecter le ﬁl de mise á la terre

au ﬁl d’alimentation noir ou á celui qui est blanc.

9) Connecter les ﬁls (connecteurs non fournis). Se reporter au tableau ci-

dessous pour faire les connexions.

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

Connecter le fil noir ou

rouge de la boite

Connecter le fil blanc de la boîte

A Noir A Blanc

*Au cordon parallèle (rond et lisse)

*Au cordon parallele (à angles droits el strié)

Au bransparent, doré, marron, ou

noir sans fil distinctif

Au transparent, doré, marron, ou

noir avec un til distinctif

Fil isolé (sauf fil vert) avec

conducteur en cuivre

Fil isolé (sauf fil vert) avec

conducteur en argent

*Remarque: Avec emploi d’un fil paralléle

(SPT I et SPT II). Le fil neutre est á angles

droits ou strié et l’autre fil doit étre rond ou

lisse (Voir le schéma).

Fil Neutre

Date Issued: 10/23/09 IS-9564-CB

MOUNTING STRAP

PATTE DE FIXATION

CANOPY

CACHE

SCREW COLLAR LOOP

COLLIER-ÉCROU

THREADED RING

BAGUE FILETÉ

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

LOOP

ANNEAU

BALL STUD

PIVOT À ROTUL

10) Placer le cache au plafond.

11) Fixer le cache en serrant la bague ﬁletée sur le collier-écrou.

12) Metre l’ampoule recommandée.

13) Soulever la cage jusqu’au luminaire en plaçant la partie supérieure de la

cage à l’intérieur du toit.

14) Enﬁler les pivots à rotule dans les parties latérales supérieures et de la

cage. Serrer les pivots à rotule pour ﬁxer la cage au partie du haut.

ROOF

CHAPEAU

CAGE

Rating

Let us know what you think about the Kichler 9564LD Tournai Lamp by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Kichler 9564LD Tournai Lamp?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Kichler 9564LD Tournai Lamp. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Kichler 9564LD Tournai Lamp. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Kichler. They might be able to provide an original manual. Are you looking for the manual of your Kichler 9564LD Tournai Lamp in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand	Kichler
Model	9564LD Tournai
Category	Lamps
File type	PDF
File size	0.42 MB

All manuals for Kichler Lamps
More manuals of Lamps

Frequently Asked Questions about Kichler 9564LD Tournai Lamp

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Is all LED lighting dimmable? Verified

No, not all LED lights are dimmable. This is indicated on the packaging or the light itself.

This was helpful (462) Read more

I put a new light in my lamp but it won't turn on, why is that? Verified

Some lamps are made for light sources of a specific wattage. When a light source is inserted that requires a higher wattage than the lamp can provide, the light may not turn on. If the lamp delivers a much higher wattage than what the light source is made for, the light source can burn out.

This was helpful (315) Read more

Why is the colour of light important? Verified

There generally are two kinds of light, warm light and cold light. Cold light keeps you sharp and awake. Warm light has a relaxing effect. The warmth of the light is measured in Kelvin and is indicated on the packaging of the lamp itself.

This was helpful (255) Read more

What is lumen? Verified

Lumen is a measuring unit for the total amount of visible light emitted by a source.

This was helpful (190) Read more

What screw bases exist? Verified

Worldwide there many types of sockets, but most used are those based on the Edison screw, indicated with the letter E. In most countries screw bases E27 and E14 are standard. In the United States E26, E17, E12 and E10 are standard.

This was helpful (142) Read more

What do watts say about my lamp? Verified

Watt is a measuring unit for electricity consumption. Lamps that produce more light, generally use more Watt, but for comparing light output you should always use lumen.

This was helpful (113) Read more