Manual Kichler 84321MBK Caputo Lamp

Manual

For warranty informaon please visit: kichler.com/warranty

Fixture Diagram

Parts List

Cauons

CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel or main

fusebox before starng and during the installaon.

WARNING:

This xture is intended for installaon in accordance

with the Naonal Electrical Code (NEC) and all local code

specicaons. If you are not familiar with code requirements,

installaon by a cered electrician is recommended.

DIMMING:

This LED xture is compable with most standard

incandescent dimmers, LED dimmers, and electronic low

voltage dimmers.

For opmal performance, an electronic low voltage dimmer

should be used.

See kichler.com/dimming for a list of compable dimmers.

CLEANING:

• Always be certain that electric current is turned o before

cleaning.

• Only a so damp cloth should be used. Harsh cleaning

products may damage the nish.

[A] Outlet Box

[B] Lockup Knob

[C] Hexnut

[D] Mounting

Strap

[E] Canopy

[F] Strap

Mounting

Screw

[G] Threaded

Pipe

1) Take threaded pipe[G] from parts bag and screw on

hexnut[C] a minimum of 13 mm (1/2”) as shown.

2) Screw threaded pipe into mounng strap[D] unl hexnut

prevents the pipe from screwing any further. Mounng

strap must be posioned with extruded thread facing

into outlet box[A] as shown. Threaded pipe must

protrude out the back of mounng strap far enough

to fully engage second hexnut. If necessary, adjust the

posion of rst hexnut on threaded pipe to ensure full

engagement of second hexnut.

3) Screw second hexnut onto end of threaded pipe

protruding from back of mounng strap. Hexnut should

be screwed down onto threaded pipe unl mounng

strap prevents the hexnut from screwing any further.

4) Aach mounng strap[D] to outlet box[A] using the

strap mounng screws[F]. Mounng strap can be

adjusted to suit posion of xture.

5) Grounding instrucons: (See Illus. a or b).

a) On xtures where mounng plate is provided with a

hole and two raised dimples, wrap ground wire from

outlet box around green ground screw, and thread

into hole.

b) On xtures where a cupped washer is provided,

aach ground wire from outlet box under cupped

washer and green ground screw, and thread into

mounng plate.

If xture is provided with ground wire, connect xture

ground wire to outlet box ground wire with wire

connector aer following the above steps. Never connect

ground wire to black or white power supply wires.

6) Make wire connecons. Reference chart below for

correct connecons and wire accordingly.

Connect Black or Red

Supply Wire to:

Connect White Supply

Wire to:

Black White

*Parallel cord (round &

smooth)

*Parallel cord (square &

ridged)

Clear, Brown, Gold or

Black without Tracer

Clear, Brown, Gold or Black

with Tracer

Insulated wire (other

than green) with copper

conductor

Insulated wire (other

than green) with silver

conductor

*Note: When parallel wire (SPT

1 & SPT 2) are used. The neutral

wire is square shaped or ridged

and the other wire will be round

in shape or smooth (See illus.)

Neutral Wire

7) Raise xture to ceiling, carefully passing threaded pipe

aached to mounng strap through center hole in

canopy[E].

8) Screw lockup knob[B] onto threads protruding through

hole in center of canopy.

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

a

b

Installaon Instrucons

This device complies with part 15 of the FCC Rules. Operaon is subject to the following two

condions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference that may cause

undesired operaon.

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protecon against harmful interference in a residenal installaon. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instrucons, may cause harmful interference to radio communicaons. However, there is

no guarantee that interference will not occur in a parcular installaon. If this equipment does

cause harmful interference to radio or television recepon, which can be determined by turning

the equipment o and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separaon between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Informaon:

IS-84321-US

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

REV 26-MAR-2021

G

D

E

C

A

F

C

B

84321

13 mm (1/2”)

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Kichler 84321MBK Caputo Lamp. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Kichler. They might be able to provide an original manual. Are you looking for the manual of your Kichler 84321MBK Caputo Lamp in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Kichler Lamps
More manuals of Lamps

Frequently Asked Questions about Kichler 84321MBK Caputo Lamp

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.