Home > Home & Decoration > Lamps > Kichler Lamps > Kichler 49628WZC Bridge Lamp

Manual Kichler 49628WZC Bridge Lamp

Need a manual for your Kichler 49628WZC Bridge Lamp? Below you can view and download the PDF manual for free in English. This product currently has 7 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

1) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work

without shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your

home. Place the main power switch in the “OFF”

position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

switch(s), that control the power to the ﬁxture or room

that you are working on.

c) Place the wall switch in the “OFF” position. If the ﬁxture

to be replaced has a switch or pull chain, place those in

the “OFF” position.

2) Find the appropriate threaded holes on mounting

strap. Assemble mounting screws into threaded holes.

3) Attach mounting strap to outlet box. (Screws not provided).

Mounting strap can be adjusted to suit position of ﬁxture.

4) Make wire connections (connectors not provided.) Reference

chart below for correct connections and wire accordingly.

5) Push ﬁxture to wall, carefully passing mounting screws

through holes in ﬁxture.

6) Thread threaded balls onto mounting screws. Tighten

threaded balls to secure ﬁxture to wall.

7) Insert recommended bulb.

8) Carefully place glass down inside bottom cage.

9) Raise bottom cage with glass up to ﬁxture. Carefully pass

hole in top of glass over bulb. Fit glass inside top of cage.

10) Align holes along edge of bottom of cage with holes along

edge of top of cage.

11) Thread one ﬁnial down through each hole in top of cage and

through hole in bottom of cage.

12) Screw one threaded cap onto end of each ﬁnial protruding

bottom edge of bottom cage. Tighten ﬁnials to secure

bottom cage to top cage.

INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND/

OR IN WET LOCATIONS.

13) Mounting surface should be clean, dry, ﬂat and 1/4” larger

that the canopy on all sides. Any gaps between the mounting

surface and canopy exceeding 3/16” should be corrected

as required.

14) With silicone caulking compound, caulk completely around

where back of canopy meets the wall surface to prevent

water from seeping into outlet box.

1) COUPER LE COURANT.

IMPORTANT: TOUJOURS couper l’électricité avant de

commencer le travail.

a) Localiser le coffret à fusibles ou le disjoncteur du

domicile. Mettre l’interrupteur principal en position

d’Arrêt.

b) Dévisser le ou les fusibles (ou mettre le disjoncteur sur

Arrêt) qui contrôlent l’alimentation vers le luminaire ou la

pièce dans laquelle le travail est effectué.

c) Mettre l’interrupteur mural en position d’Arrêt. Si le luminaire

à remplacer est doté d’un interrupteur ou d’une chaîne

connectée à l‘interrupteur, placer ces éléments en

position d’Arrêt.

2) Trouver les trous ﬁletés appropriés sur la barrette de montage.

Vissez les vis de montage dans les trous ﬁletés.

3) Visser la barrette de montage à la boite de jonction. (Vis

non fournies). La barrette de montage peut etre ajustée pour

convenir à la position de l’applique.

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

Date Issued: 9/4/15

IS-49628-CB

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

4) Connecter les ﬁls (connecteurs non fournis). Se reporter au

tableau ci-dessous pour faire les connexions.

5) Plaquez l’applique contre le mur, en passant soigneusement

les vis de montage dans les trous du luminaire.

6) Visser les boules ﬁletées sur les vis de montage. Serrer les

boules ﬁletées pour ﬁxer le luminaire au mur.

7) Introduire l’ampoule recommandée.

8) Poser soigneusement le verre à l’intérieure de la cage

inférieure.

9) Soulever la cage inférieure avec le verre jusqu’au luminaire.

Passer soigneusement le trou en haut du verre sur l’ampoule

Placer le verre à l’intérieur de la partie supérieure de la cage.

10) Aligner les trous situés le long de la partie inférieure aux

trous le long du bord supérieure de la cage.

11) Visser un ornement dans chaque trou en haut de la cage et

par le trou dans la partie inférieure de la cage.

12) Visser un bouchon ﬁleté sur l’extrémité de chaque ornement

sortant du bord inférieur de la cage inférieure. Serrer les

ornements pour ﬁxer la cage inférieure sur la cage supérieure.

INSTRUCTIONS DE MONTAGE DE LUMINAIRE À L’EXTÉRIEUR

ET/OU DANS DES LIEUX HUMIDES.

13) La surface de montage doit être propre, sèche, plate et de

0,6 cm plus épaisse que le cache sur tous les côtés. Tout

écart entre la surface de montage et le cache dépassant de

0,5 cm doit être rectiﬁé selon les besoins.

14) À l’aide de matériaux d’étanchéité à la silicone, calfeutrer

bien autour où l’arrière du cache entre en contact avec le

mur pour empêcher l’eau de passer dans la boîte de

raccordement.

Connecter le fil noir ou

rouge de la boite

Connecter le fil blanc de la boîte

A Noir A Blanc

*Au cordon parallèle (rond et lisse)

*Au cordon parallele (à angles droits el strié)

Au bransparent, doré, marron, ou

noir sans fil distinctif

Au transparent, doré, marron, ou

noir avec un til distinctif

Fil isolé (sauf fil vert) avec

conducteur en cuivre

Fil isolé (sauf fil vert) avec

conducteur en argent

*Remarque: Avec emploi d’un fil paralléle

(SPT I et SPT II). Le fil neutre est á angles

droits ou strié et l’autre fil doit étre rond ou

lisse (Voir le schéma).

Fil Neutre

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

THREADED BALL

BOULE FILETE

MOUNTING STRAP

COLLLIER DE FIXATION

BOTTOM CAGE

CAGE INFÉRIEURE

FINIAL

ORNEMENT

TOP CAGE

CAGE SUPÉRIEURE

GLASS

VERRE

THREADED CAP

BOUCHON FILETÉ

Rating

Let us know what you think about the Kichler 49628WZC Bridge Lamp by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Kichler 49628WZC Bridge Lamp?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Kichler 49628WZC Bridge Lamp. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Kichler 49628WZC Bridge Lamp. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Kichler. They might be able to provide an original manual. Are you looking for the manual of your Kichler 49628WZC Bridge Lamp in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand	Kichler
Model	49628WZC Bridge
Category	Lamps
File type	PDF
File size	0.08 MB

All manuals for Kichler Lamps
More manuals of Lamps

Frequently Asked Questions about Kichler 49628WZC Bridge Lamp

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Is all LED lighting dimmable? Verified

No, not all LED lights are dimmable. This is indicated on the packaging or the light itself.

This was helpful (462) Read more

I put a new light in my lamp but it won't turn on, why is that? Verified

Some lamps are made for light sources of a specific wattage. When a light source is inserted that requires a higher wattage than the lamp can provide, the light may not turn on. If the lamp delivers a much higher wattage than what the light source is made for, the light source can burn out.

This was helpful (315) Read more

Why is the colour of light important? Verified

There generally are two kinds of light, warm light and cold light. Cold light keeps you sharp and awake. Warm light has a relaxing effect. The warmth of the light is measured in Kelvin and is indicated on the packaging of the lamp itself.

This was helpful (255) Read more

What is lumen? Verified

Lumen is a measuring unit for the total amount of visible light emitted by a source.

This was helpful (190) Read more

What screw bases exist? Verified

Worldwide there many types of sockets, but most used are those based on the Edison screw, indicated with the letter E. In most countries screw bases E27 and E14 are standard. In the United States E26, E17, E12 and E10 are standard.

This was helpful (142) Read more

What do watts say about my lamp? Verified

Watt is a measuring unit for electricity consumption. Lamps that produce more light, generally use more Watt, but for comparing light output you should always use lumen.

This was helpful (113) Read more