Home > Home & Decoration > Lamps > Kichler Lamps > Kichler 15820CBR27 Stepped Lamp

Manual Kichler 15820CBR27 Stepped Lamp

Need a manual for your Kichler 15820CBR27 Stepped Lamp? Below you can view and download the PDF manual for free in English. This product currently has 7 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

SAFETY INSTRUCTIONS

READ THIS FIRST

KEEP THESE INSTRUCTIONS

This xture is intended for installation in accordance with the National

Electric Code (NEC) and Local code specications. Failure to adhere to

these codes and instructions may result in serious injury and/or property

damage and will void the warranty.

1) WARNING: This xture is not to be installed within 10 feet (3M) of a pool,

spa or fountain.

2) This xture is to be used only with a power unit (transformer) rated a

maximum of 300 W (25 AMPS) 15 volts.

3) The #18 ga. xture wire is not intended for direct burial.

4) Direct burial rated wire is to be buried a minimum of 6” (152mm) beneath

the surface of the ground.

NOTE: If additional Direct Burial wire is needed, contact your local Kichler

landscape distributor.

• 8 GA wire can be purchased in length of 250’ (76 M), 15503-BK.

• 10 GA wire can be purchased in length of 250’ (76 M), 15504-BK.

• 12 GA wire can be purchased in lengths of 100’ (30 M), 15501-BK; 250’

(76 M), 15502-BK; 500’ (152M), 15505-BK; and 1000’ (304 M), 15506-BK.

5) Fixture shall not use a tungsten halogen lamp unless the xture is marked

for use with such lamps.

6) Wiring connections must be made with approved/listed wire connection

device(s) suitable for the application. Do not exceed manufacturers’ wiring

combination specications for size and quantity of conductors.

CAUTION

WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE),

CARE SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS.

WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES,

GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED ON THE LIGHT

BULB, LENS, OR BODY OF THE FIXTURE.

ASSEMBLY AND INSTALLATION

1) Determine desired location for mounting xture.

2) At desired location, hammer stake (A) into ground. To avoid damage to

stake, place a board on top of stake while hammering. If ground is hard

and stake is difcult to install, make a crosscut in ground using a at shovel.

3) Clear away area in ground at wireway slot (B) in top of stake (A).

4) Lay 12V cable into wireway slot (B) and screw stem (D) into stake (A).

If assembly does not look straight, adjust by pushing or pulling on stake

only.

5) Screw shade (C) onto stem (D).

6) TURN OFF POWER.

7) Make wire connections using supplied Quic Disc

™

following instructions

below, or using other approved wiring connection method (not supplied.)

8) For CO Finish: Please handle xture with protective gloves as natural oils

from hands can cause an accelerated patina on nish.

Date Issued: 3/9/12 IS-15821-US

QUIC DISC

™

WIRING INSTRUCTIONS

Turn off power.

The full length of the 18 GA xture wire may be used to connect with the 10 GA or 12 GA cable provided the following conditions are met:

• Wiring is to be protected by routing close to the xture or accessory or secured to a building structure such as house or deck.

• 18 GA xture wiring is to be cut off so that it is attached to the connector within 6 inches of the xture or building structure.

• If it is necessary to make the connections underground, then no more than 6 inches of the 18 GA xture wire is to be buried.

The Quic Disc

™

connector is designed to install one xture and accommodates one 18 GA xture wire and one 10 GA or one 12 GA supply wire.

Place the 10 gauge supply wire across the area marked 10 GA on Quic Disc

™

or place the 12 gauge supply wire across the area marked 12 GA

on Quic Disc

™

Place the 18 gauge xture wire across the area marked 18 GA on the Quic Disc

™

. After the wires are in place, connecta the top of the Quic

Disc

™

to the base with supplied screw, making sure that the wires remain at in the bottom portion of the Quic Disc

™

, and the screw is tightened

all the way down.

The copper contacts will automatically pierce the wires’ insulation. Excess 18 GA xture wire that sticks out the end of the Quic Disc

™

is to be cut off.

Make no other wiring connections to the 18 GA xture wire.

For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page

Para informacion de la garantia por favor visite: www.landscapelighting.com/portal/warranty_page

INSTALLATION INSTRUCTIONS

Model 15820 (CP300504, CP300505, CP300506)

Model 15821 (CP300596, CP300597, CP300598)

Rating

Let us know what you think about the Kichler 15820CBR27 Stepped Lamp by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Kichler 15820CBR27 Stepped Lamp?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Kichler 15820CBR27 Stepped Lamp. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Kichler 15820CBR27 Stepped Lamp. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Kichler. They might be able to provide an original manual. Are you looking for the manual of your Kichler 15820CBR27 Stepped Lamp in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand	Kichler
Model	15820CBR27 Stepped
Category	Lamps
File type	PDF
File size	0.23 MB

All manuals for Kichler Lamps
More manuals of Lamps

Frequently Asked Questions about Kichler 15820CBR27 Stepped Lamp

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Is all LED lighting dimmable? Verified

No, not all LED lights are dimmable. This is indicated on the packaging or the light itself.

This was helpful (495) Read more

I put a new light in my lamp but it won't turn on, why is that? Verified

Some lamps are made for light sources of a specific wattage. When a light source is inserted that requires a higher wattage than the lamp can provide, the light may not turn on. If the lamp delivers a much higher wattage than what the light source is made for, the light source can burn out.

This was helpful (355) Read more

Why is the colour of light important? Verified

There generally are two kinds of light, warm light and cold light. Cold light keeps you sharp and awake. Warm light has a relaxing effect. The warmth of the light is measured in Kelvin and is indicated on the packaging of the lamp itself.

This was helpful (287) Read more

What is lumen? Verified

Lumen is a measuring unit for the total amount of visible light emitted by a source.

This was helpful (228) Read more

What screw bases exist? Verified

Worldwide there many types of sockets, but most used are those based on the Edison screw, indicated with the letter E. In most countries screw bases E27 and E14 are standard. In the United States E26, E17, E12 and E10 are standard.

This was helpful (172) Read more

What do watts say about my lamp? Verified

Watt is a measuring unit for electricity consumption. Lamps that produce more light, generally use more Watt, but for comparing light output you should always use lumen.

This was helpful (149) Read more