Home > Home & Decoration > Lamps > Kichler Lamps > Kichler 15800AZT30R Ripley Lamp

Manual Kichler 15800AZT30R Ripley Lamp

Need a manual for your Kichler 15800AZT30R Ripley Lamp? Below you can view and download the PDF manual for free in English. This product currently has 7 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

INSTALLATION INSTRUCTIONS

Model 15800R (CP300460)

FOR USE WITH LANDSCAPE LIGHTING SYSTEMS ONLY.

1) The device is accepted as a component of a landscape lighting

system where the suitability of the CSA or UL labeled combination

shall be determined by CSA, UL respectively or the local

inspection authorities having jurisdiction.

2) Fixture shall be connected to an extra low voltage transformer

approved for use with landscape lighting systems.

3) This ﬁxture is to be connected to a secondary wiring of the

following type:

12 GA 60°C minimum type;

SPT-3 suitable for outdoor use; or

approved landscape lighting cable.

CAUTION

WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW

VOLTAGE), CARE SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY COM-

BUSTIBLE MATERIALS.

WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE

NEEDLES, GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMU-

LATED ON THE LIGHT BULB, LENS, OR BODY OF THE FIXTURE.

ASSEMBLY AND INSTALLATION

1) Determine desired location for mounting ﬁxture.

2) At desired location, hammer stake (A) into ground. To avoid

damage to stake, place a board on top of stake while hammering.

If ground is hard and stake is difﬁcult to install, make a crosscut

in ground using a ﬂat shovel.

3) Clear away area in ground at wireway slot (B) in top of stake (A).

4) Lay 12V cable into wireway slot (B) and screw stem (C) into

stake (A). If assembly does not look straight, adjust by pushing

or pulling on stake.only.

5) TURN OFF POWER.

6) Make wire connections using supplied wire nuts following

instructions on bag.

INSTRUCTIONS D’INSTALLATION

Model 15800R (CP300460)

A UTILISER UNIQUEMENT POUR LES SYSTÈMES D’ÉCLAIRAG

PAYSAGER

1) Le dispositif est accepté en tant que composant d’un système

d’éclairage paysager lorsque la compatibilité de la combinaison

étiquetée UL ou CSA (ACNOR) doit être déterminée par CSA,

UL respectivement ou les autorités d’inspection locales ayant

compétence.

2) L’appareil doit étre connecté à un transformateur supplémentaire

à basse tension approuvé pour une utilisation avec les systémes

d’éclairage paysager.

3) Cet apareil doit étre connecté à un câblage secondaire du type

12GA 60°C type minimum;

SPT-3 combatible pour utilisation extreme;

ou câble d’éclairage paysager agréé.

ATTENTION

LORS DE L’INSTALLATION D’ECLAIRAGE DE JARDIN KICHLER (TENSION DU

SECTEUR OU BASSE TENSION), PRENEZ SOIN DE LE MAINTENIR DEGAGE DE

TOUT MATERIAU COMBUSTIBLE.

LORS DE L’ENTRETIEN DE LA LAMPE, ASSUREZ - VOUS DE RETIRER LES

FEULLES, LES AIGUILLES DE PIN, LES BRINS D’HERBE, L’HUMUS, ET TOUT

DEBRIS QUI S’EST ACCUMULE SUR L’AMPOULE DE LA LAMPE, LE DIFFUSEUR

OU LE CORP DE LA LAMPE.

MONTAGE ET INSTALLATION

1) Déterminer l’emplacement où installer le luminaire.

2) Planter le poteau (A) dans le sol. Pour éviter d’endommager le

poteau avec le marteau, poser dessus un morceau de bois. Si

le sol est très dur, faire deux entailles en croix dans le sol avec

une pelle plate.

3) Dégager le sol au niveau de la fente guide-ﬁls (B) située sur la

partie supérieure du poteau (A).

Date Issued: 12/12/14 IS-15800R-CB

OUTDOOR USE ONLY

DOM ETRE INSTALLE A L’EXTERIEUR

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page

Pour de plus amples informations sur la garantie, cliquez sur le lien ci-dessous : http://www.landscapelighting.com/portal/warranty_page

4) Passer le ﬁl électrique de 12 V dans la fente guide-ﬁls (B) et

visser la tige (C) dans le poteau (A). Si le montage n’est pas

droit, le redresser en poussant ou en tirant seulement le poteau.

5) COUPER LE COURANT ÉLECTRIQUE.

6) Faire les connexions de ﬁl en utilisant les écrous fournis en

suivant les instructions sur le sac.

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

Rating

Let us know what you think about the Kichler 15800AZT30R Ripley Lamp by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Kichler 15800AZT30R Ripley Lamp?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Kichler 15800AZT30R Ripley Lamp. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Kichler 15800AZT30R Ripley Lamp. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Kichler. They might be able to provide an original manual. Are you looking for the manual of your Kichler 15800AZT30R Ripley Lamp in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand	Kichler
Model	15800AZT30R Ripley
Category	Lamps
File type	PDF
File size	0.18 MB

All manuals for Kichler Lamps
More manuals of Lamps

Frequently Asked Questions about Kichler 15800AZT30R Ripley Lamp

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Is all LED lighting dimmable? Verified

No, not all LED lights are dimmable. This is indicated on the packaging or the light itself.

This was helpful (495) Read more

I put a new light in my lamp but it won't turn on, why is that? Verified

Some lamps are made for light sources of a specific wattage. When a light source is inserted that requires a higher wattage than the lamp can provide, the light may not turn on. If the lamp delivers a much higher wattage than what the light source is made for, the light source can burn out.

This was helpful (355) Read more

Why is the colour of light important? Verified

There generally are two kinds of light, warm light and cold light. Cold light keeps you sharp and awake. Warm light has a relaxing effect. The warmth of the light is measured in Kelvin and is indicated on the packaging of the lamp itself.

This was helpful (287) Read more

What is lumen? Verified

Lumen is a measuring unit for the total amount of visible light emitted by a source.

This was helpful (228) Read more

What screw bases exist? Verified

Worldwide there many types of sockets, but most used are those based on the Edison screw, indicated with the letter E. In most countries screw bases E27 and E14 are standard. In the United States E26, E17, E12 and E10 are standard.

This was helpful (172) Read more

What do watts say about my lamp? Verified

Watt is a measuring unit for electricity consumption. Lamps that produce more light, generally use more Watt, but for comparing light output you should always use lumen.

This was helpful (149) Read more