INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACIÓN / INSTRUCTIONS D’INSTALLATION
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety.
It is very important that they are read carefully
and completely before beginning installation
of the lighting xture.
•
• To avoid possible electrical shock, before
installing your light xture, disconnect the power
by turning off the circuit breakers to the outlet box
associated with the wall switch location.
• The lighting xture must be grounded. If the
ground wire for the installation site is not present,
immediately STOP installation and consult a
qualied electrician.
• All wiring must be in accordance with national
and local electrical codes ANSI/NFPA 70. If you
are unfamiliar with wiring or in doubt, consult a
qualied electrician.
LEA Y GUARDE ESTAS INSTRUCCIONES
Estas instrucciones se proporcionan para
su seguridad. Es muy importante leerlas
detenidamente y completamente antes de
comenzar la instalación de la lámpara.
•
•
Para evitar una posible descarga eléctrica, antes
de instalar su lámpara, desconecte la energía
apagando los interruptores automáticos (breakers)
que alimentan la caja de salida asociada con la
ubicación del interruptor de pared.
• L’appareil d’éclairage doit être mis à la terre.
Si le l de terre du lieu d’installation n’est pas
présent, ARRÊTEZ immédiatement l’installation
et consultez un électricien qualié.
• Todo el cableado debe realizarse de acuerdo
con los códigos eléctricos locales y nacionales
ANSI/NFPA 70. Si no está familiarizado con
el cableado, o si tiene duda, consulte a un
electricista calicado.
LISEZ ET CONSERVEZ CES INSTRUCTIONS
Ces instructions sont fournies pour votre
sécurité. Il est très important de les lire
attentivement dans leur intégralité avant
d’entreprendre l’installation du luminaire.
•
• Pour éviter tout choc électrique, avant
d’installer le luminaire, coupez le courant en
éteignant les disjoncteurs de la boîte électrique
associée à l’interrupteur mural.
• Le luminaire doit être mis à la terre. Si le l
de terre du lieu d’installation n’est pas présent,
ARRÊTER immédiatement l’installation et
consulter un électricien qualié.
• Tout le câblage doit être conforme aux codes
électriques nationaux et locaux en vigueur et
à la norme ANSI/NFPA70. Si vous n’avez pas
l’habitude de faire ce câblage ou en cas de doute,
adressez-vous à un électricien qualié.
ENGLISH
Squire Manor
KC02902119
KC02901214
Brushed Nickel
Níquel Pulido
Nickel Brossé
Matte Black
Negro Mate
Noir Mat
19086
19087
Part #/Pieza #/Pièce #
Hardware Service Kit / Kit De Mantenimiento Del Equipo /
Trousse De Maintenance Quincaillerie
Finish/Finish/FiniModel/Modelo/Modèle
Hardware Service Kit / Kit De Mantenimiento Del Equipo /
Trousse De Maintenance Quincaillerie
KG20702199 Chrome/Cromo/Chrome19481
For Models:
Para los Modelos:
Pour les Modèles:
Here are the
tools you’ll
need to
complete your
installation:
Estas son las
herramientas
que usted
necesitará para
completar su
instalación:
Voici les outils
dont vous
aurez besoin
pour réaliser
l’installation:
Twist or tape wire
ends together to make
it easier to thread
through downrod.
Hunter Pro Tip:
In order to use a 12in rod by itself
you must rst remove the post
from the 6in rod and install it on
one of the ends of the 12in rod.
Screwdriver
Destornilladore
Tournevis
4 Light Lantern Pendant
4 Luz Farol Colgante
4 Lumière Lanterne Chaînette
Wire Strippers
Pelacables
Pince à dénuder
Pliers
Alicates
Pince
Ladder
Escalera
Échelle
Fixture weight ±2 lbs:
Peso ±2 lbs:
Poids xe ±2 lbs:
4.29 lbs (1.95 kg)
PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old
xture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the
bag. One end of the threaded post (F) should be attached to the mounting bracket (A) with a washer (D) and a hex nut
(E) in place. The other end should have the canopy loop (H) attached. Unscrew the canopy loop ring (I) from the canopy
loop (H). Depending on the placement of your junction box the position of threaded post (F) may need to be adjusted
to allow the canopy to be ush with the ceiling. Determine this by lifting mounting bracket (A) up to the junction box
and place canopy (G) over the canopy loop (H), so that it is ush with the ceiling. Adjust the position of threaded post
(F) on the mounting bracket (A) so that the canopy (G) covers at least half of the exterior threads on the canopy loop
(H) while it is securely connected to threaded post (F). The threaded post (F) can be adjusted by loosening hex nut (E)
to allow movement of threaded post (F) on mounting bracket (A). Once the ideal position of the threaded post (F) is
determined, tighten up the hex nuts (E) onto the threaded post (F) just beneath the mounting bracket (A) to secure the
threaded post in place.
ASSEMBLING THE FIXTURE
There are 4 12-inch rods (K), and 1 6-inch rod (L) included for each xture. Determine the correct number of rods needed
for proper hanging height. To lengthen the xture, add additional rods. To shorten the xture, trim the wires to desired
length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the xture’s
wiring to discard. Keep in mind that you must use at least one rod to hang the xture. Thread the wires through the rods
and pull the wires until taut before connecting the rods together. All threads should be engaged but do not overtighten
(some manual straightening of the downrods may be required). Place cup (M) onto threaded post (N) and screw rod onto
threaded post (N) on the xture. Pull the xture wires through the canopy loop ring (I), top of canopy (G), and canopy
loop (H). Screw the top rod to canopy loop (H) of canopy (G). Have a helper support the xture’s weight and attach the
mounting bracket (A) to the junction box by securely tightening the mounting screws (B).
CONNECTING THE WIRES
Attach the xture’s wires to the power supply wires from the junction
box. Connect black to black (Live); white to white (grounded); grounding
to grounding (green or copper). Twist the ends of the wire pairs together.
Then, twist on a wire connector. Make sure all twists are in the same
direction. Loop xture’s ground wire around grounding screw (C) and
tighten. If there is no ground wire (green or copper) from the junction
box, contact a qualied electrician.
FINISHING THE INSTALLATION
Place the canopy (G) ush to the ceiling and slide the canopy loop ring (I) up beneath the canopy. Tightly screw canopy
loop ring (I) onto the canopy loop (H) to properly secure the canopy (G) in place. Slide candle sleeves (O) onto sockets
(P). Install light bulbs (not included) in accordance with the xture’s specications. Do not exceed the recommended
wattage. Your installation is now complete. Turn on the power and test the xture.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light
and wipe down the xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
19086
19087
19481
©2022 Hunter Fan Co. ML034
r_022222
For Models:
Para los Modelos:
Pour les Modèles:
D
E
F
A
B
G
H
C
J
L
K
M
I
N
O
P
Join the conversation about this product
Here you can share what you think about the Hunter 19087 Squire Manor Lamp. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.