3
4.2 Hot lamination
Warning -Danger of burns on the housing
• Do not touch the housing.
• Be awarethat laminated objects arehot.
• Place the laminated object on alevel surface to cool down in order to prevent it
from curling up.
Note
Special pouches areneeded for hot lamination. They aresealed using heat. This seal
is permanent and cannot be undone. Only objects that areinsensitive to heat should
be laminated. From apouch edge of around 4mm, the objects areprotected so they
arevirtually waterproof.The thickness of the pouch determines the object's stability/
kink protection.
• The Ready LED (6) lights up solid green once the required temperature has been
reached.
• Place the object to be laminated in the corresponding hot lamination pouch.
• Guide the pouch into the middle of the front opening (4) on the device. Ensure that the
sealed end (see Fig. 2) is introduced rst.
• The document is output again at the back (1).
• If the document has not been fully laminated, repeat the initial steps.
• To interrupt the lamination process (e.g. if the intake angle is incorrect), press the roller
unlocking button (2) and correct the position of thepouch.
4.3 Switching the device off
• Move the On/Off switch (5) to the "OFF" position to switch the device off.
• Both status LEDs (6/7) go out.
• Remove the mains lead from the socket.
• Allow the device to cool down completely beforetidying it away.
5. Care and maintenance
Danger –risk of death from electric shock
Disconnect the mains plug from the socket beforestarting any cleaning work.
Warning -Danger of burns on the housing
Do not touch the housing.
Warning -damage to the device from moisture
Ensure, when cleaning, that no moisturepenetrates the device in order to avoid
irreparable damage to it.
The rollers on the laminator must be regularly clearedofdust and any glue residue. To do
so, proceed as follows:
• Switch the deviceon-asdescribed in 4.1 Switching the device on.
• Wait until the Ready status LED (6) lights up solidgreen
• Guide apiece of paper into the middle of the front opening (4).
• Repeat the process if thereisalot of dirt on the paper.
• Clean the outside of the device with aslightly damp cloth.
6. Troubleshooting
Error Possible cause Remedy
The Power LED (7) does
not light up solid red.
The On/Off switch (5) is in
the "OFF" position.
Move the On/Off switch
(5) to the "ON" position.
The mains cable (3) is not
connected correctly.
Ensurethat the mains
plug is in the mains
socket.
The socket is not live. Check the domestic fuses.
The device is faulty.Notify Customer Services.
Pouches arenot
laminated correctly.
The required temperature
has not yet been reached.
Wait until the Ready
status LED (6) lights up
solid green.
7. Technical data
Input voltage 220-240 V~
Mains Frequency 50 Hz
Dimensions (W xHxD)33x6x10.6 cm
Maximum laminating width 230 mm
Maximum laminating thickness 0.6 mm
Maximum pouch thickness 125µ
Maximum heat-up time 3-4minutes
Maximum speed 230 mm/minute
Number of heated rollers 2
8. Warranty Disclaimer
Allofthe technical information, data and instructions regarding operation contained in
these operating instructions was up to date at the time of printing and is provided based
on previous experience and to the best of ourknowledge.
Hama GmbH &CoKGassumes no liability and provides no warranty for damage resulting
from improper installation/mounting, improper use of the product or from failuretoobserve
the operating instructions and/orsafety notes.
Join the conversation about this product
Here you can share what you think about the Hama 00050573 Basic DIN A4/230 Laminator. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.