www.evolutionbuild.com
12
www.evolutionbuild.com
11
MAKING COMMON SLIDE COMPOUND CUTS
There are two types of cuts that can be made with the
slide compound mitre saw.
Slide Cutting - Loosen the side lock knob and move the
cutting head towards the operator. The saw blade is lowered
into the workpiece and then pushed to the rear of the saw to
complete the cut. Used for cutting wide pieces.
1. Put wood against fence and secure with clamp as
appropriate.
2. Loosen the slide lock knob.
3. Grasp the saw handle and pull the carriage until the
arbor (centre of saw blade) is over the front edge of the
workpiece.
4. Press the lower guard unlock lever for saw head release.
5. Switch on the saw and allow the saw to reach full speed.
6. Push the saw handle all the way down and cut through the
leading edge of the workpiece.
7. Gently push the saw handle towards the fence completing
the cut.
8. Push power head to full rear position after each cut.
9. Release the trigger to switch off the saw and allow blade
to come to a complete stop before moving hands or remove
the workpiece.
Chop Cutting - The slide lock knob is tightened and the saw
handle is pushed down to cut through the workpiece. This
type of cut is used mainly for narrow pieces.
1. Slide the cutting head to the rear as far as it will go.
2. Lock slide lock knob.
3. Place the workpiece on table and against fence and secure
with clamp as appropriate.
4. Grasp the saw handle.
5. Turn on saw and allow the saw to reach full speed.
6. Press the lower guard unlock lever for saw head release.
7. Push the saw handle down and cut the workpiece.
8. After cut is complete turn off saw, allow blade to
completely stop.
WARNING: For your convenient use, the saw has a blade
brake. Never rely on it to replace proper use of the guard
on your saw.
BODY AND HAND POSITION
1. Never place hands near cutting area and keep hand away
from the path of blade.
2. Hold workpiece firmly to the fence to prevent movement
toward the blade.
3. Before making a cut. Make a dry run with the power off so
you can see the path of the blade.
4. Keep hands in position until trigger has been released and
the blade has completely stopped.
MITRE CUT (Fig. 5)
An angle of up to 45° left or right can be obtained using
the unit.
1. Loosen the sliding rail locking knob, push the saw handle
back as far as it will go and lock the handle.
2 Loosen the mitre angle lock knob.
3. Pull up the mitre angle set lever.
4. Turn the table unit to the desired angle is indicated on the
mitre angle pointer.
5. Tighten the angle lock knob to hold the desired angle.
6. Start the saw and allow it to reach full speed before
commencing the cut.
BEVEL CUT (Fig. 6)
1. Lock the cutting head down with the cutting lock knob.
2. Loosen the bevel lock.
3. Adjust angle until the bevel angle point reaches the
desired bevel angle.
4. Tighten the bevel lock.
5. Stand to the left side of the handle to make the cut.
COMPOUND CUT
When a compound cut is required. Select the desired bevel
and mitre positions.
CUTTING BOWED MATERIAL (Fig 10 & 11)
Before cutting a workpiece, check to make sure it is not
bowed. If it is bowed, the workpiece must be positioned and
cut as illustrated. Do not position workpiece incorrectly or
try to cut the workpiece without the support of the fence.
This will cause pinching of the workpiece on the blade. The
workpiece could suddenly jump or move and your hand
could hit the blade.
CLEANING
Use only mild soap and damp cloth to clean the tool. Never
let any liquid get inside the tool; never immerse any part of
the tool into a liquid.
Regularly clean the tool’s air vents with compressed dry air.
DO NOT ATTEMPT TO CLEAN BY INSERTING POINTED
OBJECTS THROUGH OPENINGS.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrication
is required.
Mitre Bevel
Max Width
Of Cut
Max Depth
Of Cut
90º 90°
320mm
(12.59”)
75mm
(2.95”)
45°L / 45°R 45° / - 45°
225mm
(8.85”)
40mm
(1.57”)
45°L / 45°R 90°
225mm
(8.85”)
75mm
(2.95”)
90° 45° / - 45°
320mm
(12.59”)
40mm
(1.57”)
BEVEL CUT to 45° Left (Fig. 6)
1. Lock the cutting head down with the cutting head lock knob.
2. Loosen the bevel lock.
3. Adjust angle until the bevel angle point reaches the
desired bevel angle.
4. Adjust the fence guard to allow for slide mechanism.
5. Tighten the bevel lock.
6. Stand to the left side of the handle to make the cut.
BEVEL CUT to 45° Right (Fig. 6.1)
1. Lock the cutting head down with the cutting head lock knob.
2. Pull out the bevel right lock release.
3. Adjust angle until the bevel angle point reaches the
desired bevel angle.
4. Adjust the fence guard to allow for slide mechanism.
5. Replace the bevel right lock release.
6. Stand to the left side of the handle to make the cut.
EVOLUTION POWER TOOLS RESERVES THE RIGHT
TO MAKE IMPROVEMENTS AND MODIFICATIONS TO
DESIGN WITHOUT PRIOR NOTICE.
Evolution Power Tools will, within twelve (12) months from the
original date of purchase, repair or replace any goods found to
be defective in materials or workmanship, provided the product
warranty registration card has been returned to Evolution
Power Tools. This warranty is void if the tool being returned
has been used to cut materials beyond the recommendations
in the Instruction Manual or if the saw has been damaged by
accident, neglect, or improper service. This warranty does
not apply to machines and / or components which have been
altered, changed, or modified in any way, or subjected to use
beyond recommended capacities and specifications. Electrical
components are subject to respective manufacturers’
warranties. All goods returned defective shall be returned
prepaid freight to Evolution Power Tools. Evolution Power
Tools reserves the right to optionally repair or replace it with
the same or equivalent item. There is no warranty - written
or verbal – for saw blades. In no event shall Evolution
Power Tools be liable for loss or damage resulting directly
or indirectly from the use or merchandise or from any
other cause. Evolution Power Tools is not liable for any
costs incurred on such goods or consequential damages.
No ofcer, employee or agent of Evolution Power Tools
is authorised to make oral representations of fitness or to
waive any of the foregoing terms of sale and none shall be
binding on Evolution Power Tools. Questions relating to this
limited warranty should be directed to the company’s head
office, or call the appropriate helpline number.
MAINTENANCE
DOUBLE BEVEL FACILITY
12 MONTHS WARRANTY
GB
GB
GB
Join the conversation about this product
Here you can share what you think about the Evolution RAGE3-DB Mitre Saw. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.