57
High-Speed Sync
High Speed Sync (FP ash) enables the ash to synchronize with
all camera shutter speeds. This is convenient when you want to
use aperture priority for ll-ash portraits.
1
Press Function Button 2
<
> so that < > is
displayed.
2
Check that <
> is displayed
in the viewnder.
• If you set a shutter speed that is the same as or slower
than the camera’s maximum ash sync speed, <
> will
not be displayed in the viewnder.
• With high-speed sync, the faster the shutter speed, the
shorter the effective ash range.
• To return to normal ash, press <
> button again.
Then < > will disappear.
• Multi ash mode cannot be set in high-speed sync mode.
• Over-temperature protection may be activated after 15
consecutive high-speed sync ashes.
Second-Curtain Sync
With a slow shutter speed, you can create a light train following
the subject. The ash res right before the shutter closes.
Press function button 4
<
> so that < > is
displayed on the LCD panel.
Press function button 3
1 < >. The icon < >
and the exposure bracketing
amount will be highlighted on
the LCD panel.
Press < SET > button again
3 to confirm the setting. Then
your FEC and FEB settings
are displayed on the LCD
panel.
● FEB will be cancelled after three photos are taken.
● For best results, set the camera drive mode to “single” and
ensure the flash is ready before shooting.
● FEB can be used with FEC and FEL.
You can prevent the FEB from being cancelled
automatically after three photos are taken. (C.Fn-
FEB ACL , Page 74)
The FEB shooting sequence can be changed. (C.Fn-
FEB, Page 74)
C.Fn
FEB
Set the flash exposure
2 compensation amount.
● Turn the Select Dial to set
the amount.
● “0.3”means 1/3 step,
“0.7”means 2/3 step.
C.Fn
FEL: Flash Exposure Lock
FEL can lock the correct flash exposure setting for any part of the
scene. With <ETTL> displayed on the LCD panel, press the
camera’s <FEL> button. If the camera does not have the <FEL>
button, press the < * > button.
Focus the subject.
1
Press the <FEL> button.
2
● Aim the subject at the center of
the viewfinder and press <FEL>
button.
● The camera flash will fire a
preflash and the required flash
output for the subject is retained
in memory.
● Each time the <FEL> button is
pressed, a preflash will be fired
and a new flash exposure
setting will be locked.
● If the subject is too far away and underexposure, the < >
icon will blink in the viewfinder. Move closer to the subject
and try the FE lock again.
● If <ETTL> is not displayed on the LCD panel, FE lock
cannot be set.
● If the subject is too small, FE lock might not be very
effective.
● If you set a shutter speed that is the same as or slower than
the camera’s maximum flash sync speed, < > will not be
displayed in the viewfinder.
● With high-speed sync, the faster the shutter speed, the
shorter the effective flash range.
● To return to normal flash, press < > button again. Then
< > will disappear.
● Multi flash mode cannot be set in high-speed sync mode.
● Over-temperature protection may be activated after 15
consecutive high-speed sync flashes.
High-Speed Sync
High Speed Sync (FP flash) enables the flash to synchronize with all
camera shutter speeds. This is convenient when you want to use
aperture priority for fill-flash portraits.
Second-Curtain Sync
With a slow shutter speed, you can create a light train following the
subject. The flash fires right before the shutter closes.
Press function button 4 < >
button so that < > is displayed
on the LCD panel.
Press Function Button 2
1 < > so that < > is
displayed.
Check that < > is
2 displayed in the viewfinder.
SYNC
SYNC
SYNC
- 49 - - 50 -
Press function button 3
1 < >. The icon < >
and the exposure bracketing
amount will be highlighted on
the LCD panel.
Press < SET > button again
3 to confirm the setting. Then
your FEC and FEB settings
are displayed on the LCD
panel.
● FEB will be cancelled after three photos are taken.
● For best results, set the camera drive mode to “single” and
ensure the flash is ready before shooting.
● FEB can be used with FEC and FEL.
You can prevent the FEB from being cancelled
automatically after three photos are taken. (C.Fn-
FEB ACL , Page 74)
The FEB shooting sequence can be changed. (C.Fn-
FEB, Page 74)
C.Fn
FEB
Set the flash exposure
2 compensation amount.
● Turn the Select Dial to set
the amount.
● “0.3”means 1/3 step,
“0.7”means 2/3 step.
C.Fn
FEL: Flash Exposure Lock
FEL can lock the correct flash exposure setting for any part of the
scene. With <ETTL> displayed on the LCD panel, press the
camera’s <FEL> button. If the camera does not have the <FEL>
button, press the < * > button.
Focus the subject.
1
Press the <FEL> button.
2
● Aim the subject at the center of
the viewfinder and press <FEL>
button.
● The camera flash will fire a
preflash and the required flash
output for the subject is retained
in memory.
● Each time the <FEL> button is
pressed, a preflash will be fired
and a new flash exposure
setting will be locked.
● If the subject is too far away and underexposure, the < >
icon will blink in the viewfinder. Move closer to the subject
and try the FE lock again.
● If <ETTL> is not displayed on the LCD panel, FE lock
cannot be set.
● If the subject is too small, FE lock might not be very
effective.
● If you set a shutter speed that is the same as or slower than
the camera’s maximum flash sync speed, < > will not be
displayed in the viewfinder.
● With high-speed sync, the faster the shutter speed, the
shorter the effective flash range.
● To return to normal flash, press < > button again. Then
< > will disappear.
● Multi flash mode cannot be set in high-speed sync mode.
● Over-temperature protection may be activated after 15
consecutive high-speed sync flashes.
High-Speed Sync
High Speed Sync (FP flash) enables the flash to synchronize with all
camera shutter speeds. This is convenient when you want to use
aperture priority for fill-flash portraits.
Second-Curtain Sync
With a slow shutter speed, you can create a light train following the
subject. The flash fires right before the shutter closes.
Press function button 4 < >
button so that < > is displayed
on the LCD panel.
Press Function Button 2
1 < > so that < > is
displayed.
Check that < > is
2 displayed in the viewfinder.
SYNC
SYNC
SYNC
- 49 - - 50 -
Join the conversation about this product
Here you can share what you think about the Cullmann CUlight FR 60C (for Canon) Flash. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.
reply | This was helpful (0) (Translated by Google)