Manual Bosch TDA2623GB Iron

Manual

1 Your iron

Beaker*

M.Shot of steam

button

K . Power cable

G. Soleplate

D. Spray outlet

N. Spray button

I. Temperature

regulator

L. "secure" lamp*

C. Water tank inlet

A. Steam regulator

E. Water tank

B. Steam regulator pointer

H. Temperature

regulator pointer

F. Water tank

level mark

* Model dependent

J. Pilot lamp

Before using the for the rst time

Please carry out the following steps:

1. Remove the protective cover from the soleplate before using the iron.

2. While the iron is unplugged, ll the water tank (E) with tap water

and set the temperature regulator (I) to “max” by lining it up with the

pointer (H).

3. Plug the appliance into the mains and when the iron has reached

the correct temperature (the pilot lamp J goes out), set the steam

regulator (A) to the “2” position.

4. Hold the iron horizontally and repeatedly press the shot of steam

button (M). Any residue should come out of the soleplate (G). It may

smoke and smell – this is normal and will cease after a short while.

5. If necessary, carefully clean the soleplate down with a damp, folded

cloth.

2 Filling the water tank

Set the steam regulator (A) to the “0” position by lining it up with

the pointer (B) on the iron and unplug the iron from the mains!

1. Place the iron at an angle of 45° with the point facing upwards.

2. Fill the water tank (E) via the water tank inlet (C) but never above

the “max” mark (F) using the beaker *.

45º

Use only clean water from the tap and do not mix anything with it. The

addition of other liquids, such as perfume, will damage the appliance.

Do not use condensation water from tumble dryers, air conditioners or

similar appliances. This appliance has been designed to use normal

tap water.

To prolong the optimum steam function it is possible to mix tap water

with distilled water 1:1. If the tap water in your district is very hard, mix

tap water with distilled water 1:2.

You can inquire about the water hardness with your local water supplier.

3 Setting the temperature

The temperature regulator (I) adjusts the temperature of the

soleplate (G).

Check the temperature instructions shown on the care label of the

garment you are ironing and set the temperature regulator (I) to the

corresponding position by lining it up with the temperature regulator

pointer (H) on the iron:

Fabric Temperature Setting

Synthetics ●

Silk - Wool ●●

Cotton - Linen ●●●

The pilot lamp (J) will stay lit while the iron is heating up and go out once

the selected temperature has been reached. Wait for a few seconds

after the light goes out before you start ironing. Once the iron is ready,

you can continue to iron even if the pilot lamp comes on again.

Tipps:

1. Sort your garments based on their care labels, always starting with

those that have to be ironed at the lowest temperature.

2. For silk, woollen or synthetic materials iron the reverse side of the

fabric to prevent shiny patches. Avoid using the spray function to

prevent stains.

4 Ironing with steam

The steam regulator (A) is used to adjust the amount of steam

produced when ironing.

1. Make sure that there is water in the tank (E).

2. Adjust the temperature regulator (I) and then set the steam regulator

(A) according to the table below by lining it up with the steam regulator

pointer (B). Steam will automatically be produced.

Temperature Setting Steam Regulator Setting

●●● to “max” 2

●● 1

Note: At a temperature setting of “•”, the soleplate is not hot enough

to produce steam, so the steam regulator (A) should be set to the “0”

position to avoid water dripping from the soleplate (G).

5 Extra steam

To facilitate the ironing of very creased laundry or thick materials, the

volume of steam can be increased briey. Press and hold the steam

regulator (A) for a maximum of 2 seconds.

2 sec

6 Shot of steam

This can be used to remove stubborn wrinkles or to press in a

sharp crease or pleat. It cannot be used on a synthetic setting

for delicate items.

1. Set the temperature regulator (I) to the “•••” or “max” position and

the steam regulator (A) to the “2” position.

2. Press the shot of steam button (M) on the handle repeatedly at

intervals of 5 seconds.

5 sec

7 Vertical steam

This can be used to remove creases from hanging clothes, curtains

etc. It cannot be used on a synthetic setting for delicate items.

WARNING! Do not vertical steam while the item is being worn.

Never spray or aim steam at people or animals!

1. Set the temperature regulator (I) to the “•••” or “max” position and

the steam regulator (A) to the “2” position.

2. Hold the iron in an upright position about 10 cm / 4 in away from the

garment being steamed.

2. Press the shot of steam button (M) on the handle at intervals of 5

seconds. However, after 4 jets of steam, wait for 10 seconds to allow

for continued steam production.

8 Ironing without steam

This function enables the iron to be used for dry ironing.

1. Set the steam regulator (A) to the “0” position.

2. Select an appropriate temperature for the type of material being

ironed.

9 Spray

This can be used to remove stubborn wrinkles.

Do not use the spray function with silk as staining may occur.

10 After each ironing

Set the steam regulator (A) to “0” and remove the plug!

1. Hold the iron upside down over a sink and shake it gently until all

the water has come out from the water tank inlet (C).

2. Set the iron aside in a vertical position to cool down.

3. Coil the power cable (K) loosely around the heel of the iron before

storing.

4. Store the iron in an upright position.

11 Multiple de-scaling system

Depending on the model, this range is equipped with the

“AntiCalc” (component 1 + 2 + 3) descaling system.

A. self-clean

Each time you use the steam regulator (A), the “self-clean” system

cleans the mechanism of any scale deposits.

B. Calc’nClean

The “Calc’nClean” function helps to remove scale particles out of the

steam chamber. Use this function approximately every 2 weeks:

1. Set the temperature regulator (I) to the “max” position and plug in

the iron.

2. After the necessary warm-up period (the pilot lamp J goes out),

unplug the iron.

3. Hold the iron over a sink and remove the steam regulator (A) by

turning it to the “calc” position while pressing it.

4. Slowly pour water (approximately 300 ml) into the steam regulator

hole.

300 ml

5. Gently shake the iron. Boiling water and steam will come out of

the soleplate (G), carrying scale or deposits that might be there.

When the iron stops dripping, reassemble the steam regulator by

reinserting it, lining up the “calc” position with the pointer, pressing

it in and turning it to the “0” position.

6. Plug in the iron. Heat up the iron again until the remaining water has

evaporated.

Tip:

If the steam regulator needle is soiled, remove any deposits from the

tip with vinegar and rinse it off with clean water.

C. anti-calc

The anti-calc cartridge has been designed to reduce the build-up of

scale produced during steam ironing, helping to extend the useful life

of your iron. Nevertheless, the “anti-calc” cartridge cannot remove all

of the scale that is produced naturally over time.

Additional Features (Model dependent)

12 Anti-drip system

This system will automatically stop the iron producing steam when the

selected temperature setting is too low to prevent water from dripping

out of the soleplate.

You may hear a clicking sound when this system is in operation.

DripStop

13 Large lling inlet with lid

14 “secure” auto shut-off function

The “secure” auto shut-off function switches off the iron when

it is left unattended, thus increasing security and saving energy.

1. Plug in the iron.

2. Initial heating up process: this function will be inactive for the rst

two minutes in order to give the appliance time to reach the set

temperature.

3. The safety circuit will switch the appliance off automatically and the

indicator lamp (L) will start ashing in the following cases:

a

If the iron is not moved for 30 seconds while resting on its

soleplate (G) or on its side.

b

If the iron is not moved for 8 minutes while in the upright position.

4. To reconnect the iron, just move it about gently.

a

b

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Bosch TDA2623GB Iron. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Bosch. They might be able to provide an original manual. Are you looking for the manual of your Bosch TDA2623GB Iron in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Bosch Irons
More manuals of Irons

Frequently Asked Questions about Bosch TDA2623GB Iron

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Bosch TDS3530GB Sensixx Iron

Manual

Bosch TDA1501CH Iron

Manual

Bosch TDA7650 Iron

Manual

Bosch TDA6665 Sensixx B5 Automatic Iron

Manual

Bosch TDS3520 Sensixx Iron

Manual

Bosch TDS1015 Iron

Manual

Bosch TDS6040GB EasyComfort Iron

Manual

Bosch TDS1445GB Iron

Related categories