Manual Aube TH136 Thermostat

Manual

TH136 400-136-001-C 2008-02-01 1/2

TH136 Programmable

Thermostat

Owner’s Guide

Your new electronic thermostat is equipped with a microprocessor

with proportional integral adaptive (PIA) temperature control

technology for total comfort.

1.1 Guidelines

Turn off power to the heating system at the main power panel to

avoid electrical shock. The installation must be performed by an

electrician.

 High voltage thermostats must be installed onto an electrical

box.

 For a new installation, choose a location about 1.5 metres above

the floor.

 The thermostat must be installed facing the heating system.

 The thermostat must be installed on an inside wall.

 Avoid locations where there are air drafts (top of staircase, air

outlet), dead air spots (behind a door), direct sunlight or

concealed chimneys or stove pipes.

1.2 Installation Procedure

n Remove the screw holding the control module to the power

base.

NOTE: Please note that the screw cannot be completely removed.

o Lift the control module to remove it from the power base.

p On the power base, remove the screw holding the wire cover

and wire the thermostat.

NOTE: The terminals are designed for wires of cross-section mea-

suring 0.33 to 2.5 mm

2

.

q Once all wiring is complete, secure wire cover.

r Secure the power base onto the electrical box using the

mounting holes.

s Mount the control module onto the power base and secure using

the screw.

t Return power to the heating system.

NOTE: Keep the thermostat's air vents clean and free from obstruc-

tions.

The TH136 is equipped with a remote input which allows connection of a

telephone controller (optional CT240) or a home automation system.

When a signal is received through this input, the TH136 will automatically

switch from normal operating mode to Frost Protection mode, or vice

versa.

NOTE: For details on operating the telephone controller, see Operating

Modes.

2.1 Connection to the CT240

Connect CT240 terminals A and C to

TH136 terminals X and C respectively.

You must respect the polarity.

2.2 Connection to a home

automation system

Connect the TH136 to the home

automation system as displayed in the

wiring diagram.

When you first install the batteries, the unit runs a

sequence of tests which lasts approximately 5 seconds.

After the tests, the screen should display the current

temperature.

NOTE: We recommend replacing the batteries at least

once a year.

The TH136 will display an icon indicating that the

batteries must be replaced. This icon will be displayed

for 60 days; after this delay, the TH136 will shut down

the heating unit. Once batteries have been replaced,

you will have to reprogram the clock & day settings; all

other programming is stored in a protected memory.

On/Off Button

The thermostat is equipped with an On/Off button

making it possible to put the thermostat in sleep mode

when its use is not required (e.g. summer). This will not

affect the clock or programming.

n Press ; the hour segment flashes.

o Press to set the hour.

p Press ; the minutes segment flashes.

q Press to set the minutes.

r Press ; the day flashes.

s Press to set the day.

t Press to exit.

5.1 Automatic

Executes the schedule. Press Auto to activate the

Auto mode.

5.2 Manual

Maintains a constant temperature. Press to

activate the Manual mode and set the temperature

using .

5.3 Frost Protection

Maintains the Frost Protection setpoint during a

prolonged absence. The Frost Protection setpoint is

pre-programmed to 10°C. To modify, see Advanced

Programming. There are 2 ways to activate the

Frost Protection mode:

n From the thermostat:

Press for 1 second to activate the Manual

mode. Hold for 3 seconds. The icon is

displayed. To deactivate the Frost Protection

mode, activate the Auto or Manual mode.

o

From a telephone (remote location) when the TH136

is connected to a CT240 telephone controller.

NOTE: For details on how to activate the Frost Protection mode using a

telephone, refer to the CT240 Instruction Manual.

WARNING: When the Frost Protection mode is activated remotely, it

must be deactivated remotely.

n

Installation & Wiring

1.

n Clock/Day settings

o Setpoint is displayed

when arrow appears

p Program settings

q Heating is On

r Return/Exit

s Power (On/Off)

t Manual mode

u Auto mode

v Current program

w Adjustment buttons



o

Remote Input Wiring

2.

p

Installing the Batteries

3.

q

Clock and Day Settings

4.

r

Operating Modes

5.

Automatic

Manual

Frost Protection

400-136-001-C_ENG.fm Page 1 Friday, February 1, 2008 10:34 AM

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Aube TH136 Thermostat. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Aube. They might be able to provide an original manual. Are you looking for the manual of your Aube TH136 Thermostat in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Aube Thermostats
More manuals of Thermostats

Frequently Asked Questions about Aube TH136 Thermostat

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.