Manual ALNO ADU 3040 S Cooker Hood

Manual

3

a horizontal line through the vertical line

at 772 mm above the height of the

hotplate. Measure 284 mm either side of

the vertical line for the 600 mm wide hood

or 434 mm either side of the vertical line

for the 900 mm wide hood.

B mm 600 900

A mm 284 434

B = Width of the cooker hood in mm

A = Distance between the centres of the

holes and the centre of the hood.

3 - Fixing the wall brackets item 2.

a - Place one of the two wall brackets item 2

(fig. 1) 15 mm from the ceiling or from

a horizontal line drawn between the top

of the adjoining wall cabinets, ensuring

that the bracket is level and mark the

centre for the key hole bracket fixing

screws.

b - Mark on the wall the centres of the two

keyholes of the bracket.

c - Place the other wall bracket item 2 fig. 1

on the wall at “X”; this measurement

should be determined by the height of the

upper chimney stack and mark the centres

for the key hole bracket fixing screws.

4 - Pilot drill all the hole positions as marked on

the wall using a Ø 8 mm drill and fix the wall

brackets items 1-2 using the Ø 8 mm rawl

plugs and screws supplied.

5 - Splashback (optional)

When the splashback is to be fitted, the

distance between the cooker hood and the

cooking appliance will be determined by the

height of the splashback item F. The

splashback should be fitted before installing

the canopy. If the splashback is to be fixed to

the wall using the top and bottom fixing holes,

care must be taken to ensure that the

splashback is fitted at the correct height before

fixing it into position. The fitting should be

undertaken by a competent person, with

experience in this type of instal-lation.

If the splashback is to be fixed using only the

top fixing holes, proceed as follows:

a - Place the splashback on the worktop as

illustrated in fig. 2a, then holding it

against the wall ensuring that it is correctly

posi-tioned on the worktop mark the holes

for the top fixing screws on the wall.

b - Pilot drill the wall using a 8 mm Ø drill

and fix the splashback using the Ø 8 mm

rawl plugs and screws supplied.

c - If the fixing holes in the bottom of the

splashback are not to be used to secure

the splashback to the wall the installer

should ensure that the bottom flange is

tucked down behind the rear of the

worktop.

Installation type C (fig. 3)

This type of installation can be carried out

using only the U-shaped lower chimney item

I.

1 - Draw a vertical line on the wall from the

centre of the cooking appliance up to the upper

limit which could be a wooden shelf: this is

to ensure the correct vertical alignment of the

wall fixing brackets.

Measure down the vertical line from the top

of the adjoining wall cabinets and draw a

horizontal line at 478 mm through the vertical.

2 - Fixing the wall brackets item 1

Mark the fixing holes for the brackets on the

horizontal line as shown in the paragraph 4.1

2.

3 - Fixing the wall brackets item 2

a - Place one of the two wall brackets item 2

(fig. 1) 15 mm from the ceiling or from

a horizontal line drawn between the top

of the adjoining wall cabinets, ensuring

that the bracket is level and mark the

centres for the key hole bracket fixing

screws.

b - Mark the centres for the two key hole

fixing bracket screws on the wall.

4 - Pilot drill all the centres using a Ø 8 mm drill

and fix the wall brackets items 1-2 using Ø 8

mm rawl plugs and screws supplied.

4.2 - Fixing the canopy hood

1 - Hook the canopy hood item C onto the wall

fixing brackets ensuring that the security fixing

screws align with the holes in the centre of

the back panel of the cooker hood as illustrated

in fig. 4.

2 - Adjust the canopy item C horizontally by

rotating the screws item R inside the cooker

hood (fig. 5).

3 - Fix the cooker hood to the wall brackets item

1 using two nuts and two washers supplied.

4.3 - Electrical connection and working test

1 - The safety measures contained in paragraph 3

are to be strictly observed.

2 - Once the electrical connection has been com-

pleted, check that worktop illumination, motor

and speeds work properly.

4.4 - Ducting or recirculation fitting

1 - Ducting fitting (Installation type A/B)

a - The cooker hood can be ducted to the

out-side using either rigid or flexible fire

retar-dant ducting Ø 100 or 120 mm. The

choice should be left to the installer.

b - The ducting spigot is provided with an

air outlet of 100 mm.

When Ø 120 mm ducting is to be used it

will be necessary to convert the 100 mm

ducting spigot by cutting along the dotted

Rating

More about this manual

We understand that it’s nice to have a paper manual for your ALNO ADU 3040 S Cooker Hood. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact ALNO. They might be able to provide an original manual. Are you looking for the manual of your ALNO ADU 3040 S Cooker Hood in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for ALNO Cooker Hoods
More manuals of Cooker Hoods

Frequently Asked Questions about ALNO ADU 3040 S Cooker Hood

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

ALNO AEF 3180 N Cooker Hood

Manual

ALNO AEF 3150 F Cooker Hood

Manual

ALNO ADU 3040 N Cooker Hood

Manual

ALNO AEF 909 E Cooker Hood

Manual

ALNO AEF 3140 N Cooker Hood

Manual

ALNO AEF 3160 N Cooker Hood

Manual

ALNO AEF 3610 N Cooker Hood

Manual

ALNO AEF 3800 A Cooker Hood

Related categories