Manual Drayton Digistat+3 Thermostat

Manual

Drayton

Installation Guide

Programmable Room

Thermostat

7 Day (5-2 Day)

Models:

22083 / 22087

Power Supply:

Battery / Mains

Invensys Controls Europe

Technical Helpline: +44 (0) 845 130 7722

www.draytoncontrols.co.uk

I

nstallation / User Guide 06490044001 (0406)

Drayton

User Guide

Programmable Room

Thermostat

7 Day (5-2 Day)

Models:

22083 / 22087

Power Supply:

Battery / Mains

Invensys Controls Europe

Technical Helpline: +44 (0) 845 130 7722

www.draytoncontrols.co.uk

I

nstallation / User Guide 06490044001 (0406)

Warning

If you do not have the knowledge to install the Digistat+3 safely,

arrange for a competent electrician to install it for you. Wiring

should conform to the current IEE wiring regulations. Isolate

mains supply before removing an existing room thermostat and

fitting

Digistat+3.

Digistat+3 programmable room thermostats are double

insulated therefore Neutral and Earth connections are not

required. Unused existing cables should be safely insulated.

Location

Care should be taken to mount the

Digistat+3 on a wall, in a postion

which is not subject to direct

sunlight or draughts. Preferably it

should be mounted on an inside

wall about 1.5M (5ft) above the

floor in a position where it can

respond to room temperature but

away from the direct influence of radiators or other appliances

giving off heat

.

Installation

1.

Remove the front cover using a flat screwdriver and separate

from back plate (Fig 1).

2. Fix the back plate directly onto the wall using suitable wall

plugs and screws or mount over existing wall box (Fig 2).

3. Complete the wiring according to the connection suggestions

shown in Fig 3. For Basic boiler, Combi boiler and Basic boiler

with zone valve applications Digistat+3 with battery or mains

supply are suitable. For Electric Heat application use

Digistat+3 with mains supply only.

4. Replace the front cover by locating in position and pushing

fully onto the back cover (Fig 4).

5. Remove the battery cover using a coin (Fig 5). Battery model only.

6. Install the 2 AA batteries provided (Fig 6). Battery model only.

7. Replace battery cover (fig 7). Battery model only.

8. The Digistat+3 is now installed and will automatically start to

control the room temperature according to the pre-set

program 1 as shown in the User Guide.

The display shows the correct time and date which is

automatically set together with the actual room temperature.

Your Digistat+3 programmable room

thermostat. (7 day (5-2 Day)

Digistat+3 programmable room thermostat allows you to set

time and temperature periods (up to 6 per day) to suit your own

lifestyle. Once fully installed and powered the

Digistat+3 will

automatically set the correct time and in auto mode will control

your heating system according to pre-set program 1 (9 till 5).

The temperature is controlled by sensing air temperature,

switching on the heating when the air temperature falls below

the thermostat setting and switching it off once this set

temperature has been reached.

(Fig 1)

(Fig 2)

H

ow to change the temperature for a short time (Override).

W

hen in Auto mode you can override the existing temperature

s

etting by pressing + or -. During adjustment the temperature will

flash then stop. The

Digistat+3 will now control at this

t

emperature until the next programmed time/temperature event is

r

eached, when the

D

igistat+3

w

ill revert back to Auto mode.

Whilst in temperature override the pointer indicates both Man and

A

uto. To exit override press > to return to Auto. (Fig 1) shows

D

igistat+3

i

n override.

H

ow to set a constant room temperature (Manual mode).

M

anual mode will allow you to set a temperature, over-riding all

programs, until you exit manual mode. In this mode all pre-set

time temperature events will be disabled.

T

o enter manual mode press < until the pointer indicates MAN

(

Fig 2). The screen will only show the temperature, which can be

adjusted by pressing + or -.

O

nce you have set the temperature it will flash for 5 seconds and

t

hen stop. The D

igistat+3

w

ill now control at this temperature until

you adjust using + or - or exit by pressing > to enter Auto mode.

(Fig 1)

(Fig 2)

(Fig 4)

(Fig 6)

(Fig 7)

(Fig 5)

(Fig 3)

TEAR HERE TEAR HERE

How to set my room temperature for my holiday period.

(

Holiday Mode)

When going on holiday you can lower the temperature of your

home for the duration of your holiday, but set

Digistat+3 to

r

eturn to your normal programming ready for your return.

H

oliday mode works by counting down the days or hour until

your return.

T

ime periods of between 1 to 24hr then 1 day to 199 days can

be set.

Example

I

am ready to leave for my 2 week (14 day) holiday and would like

t

he house temperature held at a constant 10.0 ºC during this time

and on my return the house temperature will be already running

at my normal pre-set temperature.

To enter Holiday mode press the < button until the pointer is

indicating HOL (fig 3). The temperature will flash and by pressing

the + or - buttons you can change to the temperature required (

in this example to 10.0 ºC) (Fig 3a).

Then press < again to set the time period.(in this example 14

days) using the + or - buttons. (it would be advisable in this

example to set the time period 1 day less (13 days) to ensure the

house temperature is back to normal on your return). (Fig 3b)

Once you have set your time period the time will flash for 10

seconds and then start the holiday period. To exit the Holiday

mode press either < or > to return to auto mode.

When changing time the display will scroll through Hr (Hours)

1-24 then d (Days) 1-99.

The display will show holiday time period and set temperature.

(Fig 3)

(Fig 3a)

(Fig 3b)

(Fig 4) (Fig 5)

Battery Model only.

How do I know when to change the batteries.

When the batteries start to run low a battery icon will blink for

15 seconds every 15 seconds to indicate “low battery” during

this time the

Digistat+3 will function normally (see fig 4).

Please replace batteries with (2 x AA 1.5V Alkaline batteries).

After 6 months the

Digistat+3 will cease to function and will

permanently display the battery icon and nothing else, shown in

(fig 5).

(

Fig 6)

(Fig 8)(Fig 7)

(Fig 10)(Fig 9)

H

ow to change the time, day, month & year.

Digistat+3 comes with a pre-set clock, which also automatically

adjusts for summer/winter time changes. It is activated

a

utomatically on 1st installation. There should be no need to

c

hange these settings, however, should you wish to, it can be

done in clock mode.

To enter clock mode press > to select Day. Select Sunday. Use >

t

o move through all 6 time/temperature events until the arrow

p

oints to the clock symbol. The time will now flash and can be

adjusted (Fig 7) by pressing + or - then press > to accept and

m

ove to Day.

C

hange day.

(

Fig 8).

I

f you wish to change the day press + or - then press > to accept.

D

igistat+3

w

ill move to the next field - month.

C

hange month.

(

Fig 9).

If you wish to change the month press + or - then press > to

accept.

Digistat+3 will move to the next field - Year.

Change year. (Fig 10).

If you wish to change the year press + or -, then press > to

accept.

Digistat+3 will now return to Auto mode.

H

ow to replace the batteries see fig 6.

Remove the battery cover using a coin. Replace the spent

b

atteries with 2 x AA 1.5V alkaline batteries ensuring correct

o

rientation. Replace the battery cover pressing fully home.

Display Error code E1 or E2.

When the display shows E1 or E2 this indicates a sensor fault and

your heating system will remain Off. Please contact your installer.

How to select another pre-set time/temperature program.

There are 3 pre-set time/temperature programs already held in

memory as shown, if pre-set program 1 is the best program to

suit your lifestyle do nothing and the

Digistat+3 will control to

program 1.

If you would like to select one of the other pre-set programs,

refer to ‘How to change User Options’, Option 3 and select your

preferred program.

Certification Mark

06490044001 Digistat+3 update 7/3/06 11:19 am Page 1

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Drayton Digistat+3 Thermostat. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Drayton. They might be able to provide an original manual. Are you looking for the manual of your Drayton Digistat+3 Thermostat in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Drayton Thermostats
More manuals of Thermostats

Frequently Asked Questions about Drayton Digistat+3 Thermostat

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Drayton MiStat Thermostat

Manual

Drayton MiStat C Thermostat

Manual

Drayton Digistat+1 Thermostat

Manual

Drayton Digitstat+C RF Thermostat

Manual

Drayton Digistat RF3 Thermostat

Manual

Drayton MiStat N Thermostat

Manual

Drayton RTS 1 Thermostat

Manual

Drayton Digistat+2RF Thermostat

Related categories