Manual Zanussi ZGL640ISX Hob

Manual

damage to property caused by failure to obey these re-

quirements.

• To prevent the risks of structural damage or physical

injury, installation, connection of the appliance to the

power supply and gas system, setting up and mainte-

nance must only be done by qualified personnel in

compliance with standards and local regulation force.

• Make sure that the appliance is not damaged because

of transport. Do not connect a damaged appliance. If it

is necessary, speak to the supplier.

• Only use built-in appliances after you assemble the ap-

pliance into correct built-in units and work surfaces

that obey the standards.

• Do not install the hob over a domestic appliances if the

installation instructions do not allow it.

• Install the appliance only on a worktop with flat sur-

face.

• Do not change the specifications or modify this prod-

uct. There is the risk of injury and damage to the appli-

ance.

• Fully obey the laws, ordinances, directives and stand-

ards in force in the country where you use the appli-

ance (safety regulations, recycling regulations, electri-

cal safety rules etc.)

• Keep the minimum distances to other appliances and

units.

• Install anti-shock protection, for example install the

drawers only with a protective panel directly below the

appliance.

• Prevent damage of the cut surfaces of the worktop

against moisture with a correct sealant.

• Seal the appliance to the worktop with no space left

with a correct sealant.

• Prevent damage to the bottom of the appliance from

steam and moisture, e.g. from a dishwasher or oven.

• Do not install the appliance adjacent to doors and be-

low windows. Hot cookware can be hit off the hob

when you open the doors or windows.

• Before installation, make sure that the local supply

conditions (gas type and pressure) agree with the ad-

justment of appliance. The adjustment conditions for

the appliance are on the rating plate, which you can

find near the gas supply pipe.

• This appliance is not connected to a combustion prod-

ucts evacuation device. It must be installed and con-

nected in accordance with current installation regula-

tions. Particular attention must be given to the relevant

requirements regarding ventilation.

• The use of a gas cooking appliance cause heat and

moisture in the room in which it is installed. Make sure

that the ventilation in the kitchen is good: keep natural

ventilation holes open or install a mechanical ventila-

tion device (mechanical extractor hood).

• More ventilation (for example opening of a window or

increasing the level of mechanical ventilation where

present) is necessary when you operate the appliance

with intensity for a long time.

• Carefully obey the instructions for electrical connec-

tions. There is the risk of injury from electrical current.

• Disconnect the appliance from the electrical supply,

before you do the maintenance work or you clean it.

• The electrical mains terminal is live.

• Make electrical mains terminal free of voltage.

• Install correctly to give anti-shock protection.

• A loose and incorrect mains plug and socket connec-

tions can make the terminal become too hot.

• A qualified electrician must install the clamping con-

nections correctly.

• Use a strain relief clamp on cable.

• Use the correct mains connection cable and replace the

damaged mains cable with applicable cable. Speak to

your local Service Force Centre.

• The appliance must have the electrical installation

which lets you disconnect the appliance from the

mains at all poles with a contact opening width of min-

imum 3 mm.

• If the fixing bracket is near to the terminal block, al-

ways make sure the connection cable does not come in

contact with the edge of the bracket.

• You must have correct isolation devices: line protect-

ing cut-outs, fuses (screw type fuses removed from the

holder), ground leakage trips and contactors.

Disposal of the appliance

• To prevent the risk of physical injury or damage

– Disconnect the appliance from the power supply.

– Cut off the mains cable where it connects with the

appliance and discard it.

– Flat the external gas pipes if there are fitted.

– Speak to your local authorised facilities for disposal

of your appliance.

3

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Zanussi ZGL640ISX Hob. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Zanussi. They might be able to provide an original manual. Are you looking for the manual of your Zanussi ZGL640ISX Hob in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Zanussi Hobs
More manuals of Hobs

Frequently Asked Questions about Zanussi ZGL640ISX Hob

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Zanussi ZGLR646TDF Hob

Manual

Zanussi ZGO78530BA Hob

Manual

Zanussi ZK630LX Hob

Manual

Zanussi ZIL8470CB Hob

Manual

Zanussi ZVT64X Hob

Manual

Zanussi ZGNT640X Hob

Manual

Zanussi ZICK845K Hob

Manual

Zanussi ZGM64300X Hob

Related categories