Manual Xtant X604 Car Amplifier
Need a manual for your Xtant X604 Car Amplifier? Below you can view and download the PDF manual for free in English. This product currently has 0 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.
Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.
Manual
Loading…
Input Sensitivity Adjustment
The X%(" offers five ()) input gain settings* The adjustment runs in $( dB steps
from +!( dB to . !( dB* This wide range of adjustment allows the X%(" to accept
input voltages from $(( mV to $# V* Adjustment is made by installing a jumper
across the associated input voltage/pin location* Refer to the illustration on the
reverse side of this document prior to setting the input sensitivity*
Crossover Frequencies & SIP’s
The X%(" is equipped with independent Front and Rear crossovers* Each
crossover is controlled by two (!) crossover mode jumpers labeled
AAMMP & LINE
XXOVRR
*
The header jumper labeled
AAMMP XXOVRR
control the crossover function as
it applies to the X%("’s Front (stereo) and Rear (stereo) amplifier* The modes of
operation are: Position $ / Bypass (Full Range), Position ! / High Pass, and
Position ' / Low Pass and Position "/Band Pass (See insert)
The two (!) header jumpers labeled
LINE XXOVRR
control the crossover function
as it applies to the X%("’s Front and Rear RCA Line Outputs* The modes of oper+
ation are: Position $ / Bypass (Full Range), Position ! / High Pass, and Position
' / Low Pass* (See insert)
The High and Low Pass frequencies are determined by the Frequency Modules (SIPs)
installed in the eight (-) SIP sockets pictured on the insert*
Crossover Frequencies & SIP’s
The following is a chart of Xtant’s available frequencies* The frequency SIP “ID
Code” printed on the SIP and the associated frequency value is detailed below*
SIP Number Frequency
!!" )( Hz
$'" #( Hz
$$" -( Hz
$(" &( Hz
%-' $!( Hz
)%' $)( Hz
!#' '(( Hz
$)' )(( Hz
$(' #(( Hz
#)! $ kHz
!"! ' kHz
$-! " kHz
$)! ) kHz
The X%(" is shipped from the factory with &( Hz HiPass and LowPass frequency
SIP’s installed* To change a frequency, simply remove the resistor SIP and replace it
with the appropriate SIP value to achieve the desired frequency*
The Low and High Pass frequencies are independent* Any combination of the available
frequency SIP’s may be used*
4 5
Installation Instructions
This document has been crafted to make installation, system design and trouble+
shooting, a quick and easy process*
Installation Sequence
Remove Amplifier Cover:
Loosen allen head screws and lift+off cover* Do not remove protective
covering on stainless steel lid until installation is complete*
Temporarily Mount Amplifier:
The amplifier is designed to be anchored through the four (") holes located on the
circuit board/base assembly*
Mark Wires for Termination and Remove X%(":
Determine wire lengths for Power, Ground, Remote, & speaker cables* Mark for
cutting/termination* Remove X%(" before cutting and terminating all wires*
CAUTION:
stripping wires over the circuit board will cause product failure*
Crossover Set+up:
Adjust crossover mode jumpers at your work bench* Also, change crossover frequency
SIP’s if desired* Refer to crossover modes of operation on opposite page*
Input Sensitivity:
Make initial adjustment to input gain at your work bench* To increase input gain,
place jumper in the .!( dB position* To decrease input gain, place jumper in the
(, +$(, or +!( dB position* Refer to Input Sensitivity Adjustment on back panel for
more information*
Mount the Amplifier and make all connections:
NOTE:
Place service jumper in off position before making any connections* Install
the amplifier and make all wire connections* i*e:*Speaker, Power, Remote,
Ground, and RCA input*
Double Check All Connections! Turn On Amplifier*
Place service jumper in the on position, check red LED, it should be on*
Adjust Left and Right Front as well as Left and Right Rear Amplifier Output Levels*
Adjust Noise Gate Threshold (if used)
Turn noise gate on and adjust the threshold by turning clockwise to increase
sensitivity* The green LED will illuminate*
After Fine Tuning the System:
Remove protective covering from amplifier and clean per the maintanence section
on page & of the
Owner’s Manual*
Attach cover to base*
English English
Loading…
Rating
Let us know what you think about the Xtant X604 Car Amplifier by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.More about this manual
We understand that it’s nice to have a paper manual for your Xtant X604 Car Amplifier. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Xtant. They might be able to provide an original manual. Are you looking for the manual of your Xtant X604 Car Amplifier in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.
Specifications
| Brand | Xtant |
| Model | X604 |
| Category | Car Amplifiers |
| File type | |
| File size | 0.24 MB |
All manuals for Xtant Car Amplifiers
More manuals of Car Amplifiers
Join the conversation about this product
Here you can share what you think about the Xtant X604 Car Amplifier. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.