Manual Worx Landroid Lawn Mower

Need a manual for your Worx Landroid Lawn Mower? Below you can view and download the PDF manual for free in English. This product currently has 8 frequently asked questions, 94 comments and has 91 votes with an average product rating of 47/100. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

Loading…

INSTALLATION
GUIDE
Download manual in English (PDF, 32.92 MB)
(Consider the environment and only print this manual if it is really necessary)

Loading…

Rating

Let us know what you think about the Worx Landroid Lawn Mower by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.
Are you satisfied with the Worx Landroid Lawn Mower?
Yes No
47%
53%
91 votes

Join the conversation about this product

Here you can share what you think about the Worx Landroid Lawn Mower. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

Sture 08-05-2019
How to do when the display shows outside the work area. The robot is inside the work area and the wire around is intact.

reply | This was helpful (196) Read more (Translated by Google)
Bo Larsson 04-08-2019
Had the robot for 4 months. the thread is whole, but the display shows outside the working area.

This was helpful (196) (Translated by Google)
Patrik 19-05-2019
Just as bad here

This was helpful (47) (Translated by Google)
Patric Winberg 17-09-2019
Same problem. Outside work area. Cash machine.

This was helpful (40) (Translated by Google)
Bernt Ström 29-05-2019
You have connected the cables to the base plate incorrectly. Turn the cords over.

This was helpful (37) (Translated by Google)
Anders 22-07-2019
Hello My mower often stops. "outside the work area". When you restart it, it goes a few meters forward, turns for a reason a couple of times and stops again. "outside the work area". Ideas?

reply | This was helpful (180) (Translated by Google)
Mogens Davidsen 31-08-2019
I have a WR141E model M500 It is fully charged when I turn it on and enter the code - it writes Stop in the display - does anyone know what it is due to and how do I get the mower going again?

reply | This was helpful (158) Read more (Translated by Google)
Alice Svendsen 06-09-2022
my robotic lawnmower worx 500 also says stop in the display

This was helpful (7) (Translated by Google)
Tomas Knutsson 16-06-2019
Hi, I have a Worx Landroid WG795E type 02. I have changed the battery when it was completely exhausted and changing is easy but getting it to run normally again is worse. The battery is fully charged and according to the schedule it should cut but in the display it says "waiting for a cutting schedule", I have programmed both auto and manual but nothing works. If I start it with a fully charged battery, it runs for about 5 minutes, then it searches for a charging station again. Is there any tipping solution? Is it possible to reset and restart?

reply | This was helpful (127) Read more (Translated by Google)
Serdar 02-07-2019
Hi, where did you order the battery from?

This was helpful (39) (Translated by Google)
Mats viimne 05-06-2019
Has a single robot mower WG791E. Excellent machine but has the wrong date on the display. How to change the date setting? Have tried but the same date returns after the try. Mvh mats [email protected]

reply | This was helpful (116) (Translated by Google)

Loading…

Erling Sørensen 11-07-2019
Can't get it connected to wifi - what could the problem be - broadband provider is contacted and here they can see on logs that there is contact - but it does not work

reply | This was helpful (93) (Translated by Google)
Per-Anders carlsson 17-04-2019
the mower does not want to charge, charging block,

reply | This was helpful (92) (Translated by Google)
Susanne 11-05-2019
Has acquired a new battery for my older model Worx (2011). It had a stick for the update. I followed the description of the assembly and the update. The machine went out twice and then it went "home" to charge. However, it does not charge and now I do not know what is wrong. Please give me some advice.

reply | This was helpful (87) (Translated by Google)
John Holst 29-06-2019
My worx 700 is a year old. Has started driving in a weak arc. How do I remedy it.

reply | This was helpful (82) (Translated by Google)
Søren skov 02-07-2019
My robot mower has only started to run about 1.5 meters from the edge, after which it turns around again. Thus it only mows about 1.5 meters around the entire edge of the lawn. Anyone know how to fix this ?? It's a Works landroid

reply | This was helpful (79) Read more (Translated by Google)
Thomas Hillgaard 21-09-2019
Have the same problem? Have you found a solution?

This was helpful (36) (Translated by Google)
Nils Nørgaard 31-08-2019
The robot lights up constantly red on the charging indicator. Will not start. Green light on the charging station.

reply | This was helpful (77) (Translated by Google)
Kerstin Blomgren 01-09-2019
Have had him, for three years has worked great, but now he does not charge, the red light does not light, What do you think is wrong?

reply | This was helpful (71) (Translated by Google)
Bo Kortegaard 20-04-2020
My worx m500 turns off right after I turn it on. Everything also lights up fully battery but it Slides off and turns off immediately.

reply | This was helpful (64) Read more (Translated by Google)
Jan Thomsen 03-05-2020
I have the same problem. Is there a solution to that.?

This was helpful (41) (Translated by Google)
Casper 01-08-2020
Have the same problem on m500: - /

This was helpful (9) (Translated by Google)
Mikael Lindquist 03-06-2019
It often stops and says it is upside down, what to do?

reply | This was helpful (59) Read more (Translated by Google)
S Olsson 07-07-2019
It often stops and says it is upside down, what to do?

This was helpful (32) (Translated by Google)
Poul-Erik Mogensen 13-04-2020
Has a worx, older model which I have made again with new cables for the front panel Put it in charging station but can not start it. It writes out of range will not start in any way. Is there help to be found ,? PEM.

reply | This was helpful (40) Read more (Translated by Google)
Jørgen Poulsen 07-07-2020
Hi Poul-Erik. Try if necessary. just place the machine outside the perimeter wire and see if it will start here. If so, you have had the wires at the charging station replaced and you just need to replace them again. Hope it's that simple.

This was helpful (4) (Translated by Google)
Camilla 18-08-2019
Bought worx landroid about 1 month ago. Got it started, cut once, stood in the station ever since, all indications good. When we now wanted to start it again, it is completely discharged. Why does it not charge in the station?

reply | This was helpful (35) (Translated by Google)
Hasse Ankén 04-07-2019
Problems with the program. Turns off when, rain sensor does not work, Time settings "release", Moisture in the mower Sincerely, Hasse

reply | This was helpful (29) (Translated by Google)
Steen elro 23-07-2019
Hi, how to set hours on s300, (there is no network in the cottage)

reply | This was helpful (29) (Translated by Google)
Maths svensson 22-07-2019
My mower only sways to the left now, what do I do?

reply | This was helpful (26) (Translated by Google)
Jerry Erlandsson 02-05-2019
The neighbor's green wire is disturbing my lawnmower

reply | This was helpful (25) (Translated by Google)
Peter 18-04-2020
I got to break the cord after it had to be moved and am now reassembled. Now the charger flashes green instead of green all the time and the machine stops immediately. Anyone tried it?

reply | This was helpful (25) Read more (Translated by Google)
Thomas Østergaard 04-06-2020
Yes there is still a fault in the cord. Have just had the same problem. Look at your collection again otherwise there is a break somewhere else Mvh Thomas

This was helpful (3) (Translated by Google)
Henrik Fischer 18-07-2020
My machine says: "lifted up" and below it writes: "'0' = reset" It does not respond and does not charge. Hoping for a constructive answer, mvh. Henrik

reply | This was helpful (25) Read more (Translated by Google)
John Lorenzen 03-04-2022
Have the same problem

This was helpful (1) (Translated by Google)
Christoffer Bengtsson 21-09-2019
My Landroid m700 says that "wire is missing" even though it is intact. Have tried adding a new fixed shorter cable with the same result !! Gets crazy on the shit !! Anyone with any good tips or solutions?

reply | This was helpful (22) Read more (Translated by Google)
Akki Wedlin 11-05-2020
Hello Did you get an answer to your question? Namely, experiencing the same.

This was helpful (6) (Translated by Google)
Claus H. Christensen 15-10-2020
Hello. Min ca. two-year-old Works Landroid WG790E.I have started behaving strangely. If it runs in the slightest obstacle, it stops and gives "Lifted up" error. The error cannot be reset even if it is shown on the display. If I tick the machine there is an "Inverted" error which can be reset and the machine can be restarted. Anyone have a bid on what might be wrong?

reply | This was helpful (21) (Translated by Google)
Palle Vibe 27-04-2021
My Worx Landroid 500 does not work well after an overwintering. It constantly claims to be outside the work area and I can not reprogram the correct time and date etc. Can not the whole machine be reset to factory programming? And how?

reply | This was helpful (19) (Translated by Google)
Kent Kihl 25-08-2020
Installed it today, but it went a little wrong, so I lifted it up. Then the display showed "Mover stopped auto power off in 19:57" ie it starts counting down from 20 minutes. But it can not be started again, the same message appears.

reply | This was helpful (18) (Translated by Google)
Henrik Steffensen 21-07-2020
Can you program the robot yourself? eg. how far it should back up when it encounters a minor obstacle. The robot does not travel far enough back when it encounters a resistance, depression in the terrain or a grass room. The robot only runs approx. 5 cm backwards and then try again while twisting first that way and then the other with the rustic wheels. It rarely succeeds in getting the nose wheel free and then begins to dig itself down until it eventually just rests on its belly and gets nowhere.

reply | This was helpful (16) Read more (Translated by Google)
Bjarne 04-08-2021
I have the same experience. Did you find any solution?

This was helpful (2) (Translated by Google)
Malin Ragneby 14-04-2019
Where can I find the front wheels for my Worx Landroid WG794E?

reply | This was helpful (13) Read more (Translated by Google)
JC 28-07-2019
https://m.clasohlson.com/se/Hjul-Främre-Worx-Landroid/51-2613

This was helpful (12) (Translated by Google)
Bengt Svensson 09-04-2020
How much do you have to unscrew to change the keyboard

reply | This was helpful (12) (Translated by Google)
Jimmy Nilsson 20-09-2020
It often stops and says it's upside down, what to do?

reply | This was helpful (11) (Translated by Google)
zoran 25-06-2020
When you restart it, it goes a few meters forward, turns for a reason a couple of times and stops what to do

reply | This was helpful (9) (Translated by Google)
Owe 26-07-2020
Hi. I have mounted ACS on my Landroid 143. It detects trees, etc. and walks around, but climbs up on a rock that is about 50 cm high and 2 meters in diameter. What can I do? What's wrong?

reply | This was helpful (9) (Translated by Google)
Anders 23-03-2022
How to do when the display shows outside the work area. The robot is inside the work area and the wire around is intact.

reply | This was helpful (9) (Translated by Google)
Ingemar Bjärneroth 18-09-2019
Hey! Landroid 500. I wonder if there is anyone who has a lawn that has a slope of about 20-25% at the lower part of the border cable and is laid longitudinally at the bottom of the slope. Has the robot ever fallen out of track in connection with returning to the charging station when it was on this slope?

reply | This was helpful (8) (Translated by Google)
[email protected] 04-08-2019
My Landroid does not accept ladind when it comes to charging station. The mower is now 3 years old. Regards Sverre Dysthe

reply | This was helpful (7) (Translated by Google)
egil repvik 21-06-2020
Why does it come so often outside the boundary wire, especially on gentle downhills? What am I doing?.

reply | This was helpful (6) (Translated by Google)
Per olof Skoglund 02-08-2020
Bought a used one from a friend goes just fine but had to turn the cables on in and OUT but now you want to go into the charging station from the wrong direction, you can reset the work area and reinstall

reply | This was helpful (6) (Translated by Google)
V witting 31-05-2020
My worx m500 turns off right after I turn it on. Everything also lights up fully battery but it Slides off and turns off immediately.

reply | This was helpful (3) Read more (Translated by Google)
Kristian Bjerge 25-07-2020
I have the same problem that My worx m500 turns off right after I turn it on. Everything also lights up fully battery but it Slides off and turns off immediately, does anyone have a solution?

This was helpful (0) (Translated by Google)
Martin Rahn 13-09-2020
I have the same problem, what do you do? Does anyone have a solution?

This was helpful (0) (Translated by Google)
Henrik Steffensen 11-08-2020
The "boys" who have set the algorithms, probably at a major international competition in a stadium hall, have apparently never tried to cut grass. There is clearly room for improvement.

reply | This was helpful (3) (Translated by Google)
Jimmy Nilsson 20-09-2020
It often stops and says it's upside down, what to do?

reply | This was helpful (3) (Translated by Google)
perf andersen 08-08-2020
My 1 year old machine is suddenly running outside the area. is completely indifferent and continues until something stops it. The charging stand is constantly lit green, so there should be no break in the cord. Anyone have a bid on the issue ??

reply | This was helpful (1) Read more (Translated by Google)
Thomas Østergaard 08-08-2020
Do you have a neighbor with a robot cutter ??

This was helpful (0) (Translated by Google)
Dorte Pedersen 16-04-2021
How do I get my landroid to delineate my lawn? Have read that it must follow the boundary all the way around the first time, but it does not

reply | This was helpful (1) Read more (Translated by Google)
Kristian 16-04-2021
I mean it only follows the boundary wire if you put it to the edge clip

This was helpful (0) (Translated by Google)
Andreas Friberg 11-06-2021
Hello. When I clicked on the panel on my Worx Landroid, I came to the conclusion that you can set several work areas. What is meant by this? Can my Landroid run in a place with only boundary wire laid out or must there always be a charging station in the area?

reply | This was helpful (1) (Translated by Google)
Merethe Hviid 28-04-2023
Hi there The QR code on the WA3750 for the app has disappeared/fallen off How do I order a new one - here? Thanks in advance Who Merethe

reply | This was helpful (1) Read more (Translated by Google)
Merethe Hviid 13-05-2023
Is there anyone who can help???

This was helpful (0) (Translated by Google)
mette 02-05-2023
I have now put my battery back in before the summer and the machine works but my app on my phone is now in English and I can no longer set it to Dutch. can someone help me or something. everything is in Dutch on the mower. Thank you

reply | This was helpful (1) (Translated by Google)
Jens Thomsen 29-04-2019
How if you have a trampoline standing - find out for yourself or what is the best

reply | This was helpful (0) (Translated by Google)
Laga begränsningstråd 10-06-2019
Hey! My lawnmower has cut the boundary wire! How do I fix it? With kind regards, Annika

reply | This was helpful (0) (Translated by Google)
Jonna Thiemer 01-07-2019
My robot has started beeping a loud sound when it is in the charger it lights up alternately blue and red in warning triangle and when it hits grass can not find an explanation. Why does it do that? It may also suddenly stop in the middle of the lawn, be lifted to the charger and then run again.

reply | This was helpful (0) (Translated by Google)
Per jäderholm 09-07-2019
Have one of your product model 6791 serial number 30154104 have called 010 5517110 again get contact only gossip music for several hours! How do I get a manual? Can you answer me on tel 070 5114571 thank you in advance. Per Jäderholm manual was lost in connection with the move.

reply | This was helpful (0) (Translated by Google)
Larsa Westin 26-09-2019
Want to see posts

reply | This was helpful (0) (Translated by Google)
Jørgen Christensen 14-04-2020
Hello. I have previously set my android on my phone, the phone had to be deleted at some point, after which I will run the application on my new phone, but I had forgotten my password, what do I do now, the machine says it has been set up. Sincerely Jørgen

reply | This was helpful (0) Read more (Translated by Google)
Thomas Østergaard 20-04-2020
Hi Jørgen Have you found the answer to your problem. Stands immediately. It can easily run around and cut, but I can not get on the app and change it ... hope you got smarter Regards Thomad

This was helpful (0) (Translated by Google)
Malin 19-04-2020
Should start after hibernation but it says OFF in the display when I press On. Does it think it was stolen? How do I get past this? Please Malin

reply | This was helpful (0) (Translated by Google)
Danny dagsberg 28-04-2020
Worx WG796E.I Blocked Clipboard 0 = Reset motor spins easily. And service picture on display shows a six where can you get the codes so you look up the error?

reply | This was helpful (0) (Translated by Google)
Carl Gnosspelius 03-05-2020
When I press ON, it appears OFF on the display and then turns off. . What to do?

reply | This was helpful (0) (Translated by Google)
Mauri Åkerman 16-05-2020
My WG790E does not detect the restriction wire when it is to return to the charging station. It over everything that is nearby, bushes flowers, flower beds etc .. It is as if the thread does not exist! When it cuts, everything works well. How to do a factory reset?

reply | This was helpful (0) Read more (Translated by Google)
Magnus B 15-10-2020
The sensors that are supposed to detect the wire may not work. It is quite common for wires / thin cables in the sensor unit to fall off / break / come loose and then the sensors do not work as they should. The sensor unit is available for purchase as a spare part and can be replaced quite easily.

This was helpful (2) (Translated by Google)
John Skov 04-06-2020
Has a brand new wr143. When I press manual stop and want to start again, it says in the display that the power will be turned off automatically after 20 min ?? And yes, the power is turned off and If I then try to start the machine starts new 20min Can only be restarted after emergency charging

reply | This was helpful (0) (Translated by Google)
K Sidborn 08-06-2020
I get the message "disc blocked". What is the problem ? My mower is Landroid WG791E.

reply | This was helpful (0) Read more (Translated by Google)
Olle 25-06-2020
In my case, it turned out that the engine that drives the "blade" for some reason went extremely sluggishly. I ordered a new one and changed which solved my problem.

This was helpful (4) (Translated by Google)
Olle 20-06-2020
Hey! I have the same problem so I wonder if you got any solution to it. Sincerely Olle

This was helpful (0) (Translated by Google)
Åsa Pettersson 15-06-2020
Hey! Press the red (small) start button. Usually welcome me but today it is black box. Know that it happened before and we solved it, but do not remember how ??? Some tips? Tjing Åsa

reply | This was helpful (0) (Translated by Google)
egil repvik 21-06-2020
Why does it come so often outside the boundary wire, especially on gentle downhills? What am I doing?.

reply | This was helpful (0) (Translated by Google)
Lars 28-06-2020
Landroid S Stands in the charging station overnight, and when it has to start again the next day, the message comes that it is manually stopped. Tried to turn the device on and off but still not able to start it via mobile. And the charging station is level.

reply | This was helpful (0) (Translated by Google)
Jørgen Poulsen 30-06-2020
Hello. I have a problem attaching 2 pcs. M500 machines on the APP. The first gave no problem, but when I want to connect machine # 2 to WIFI, after scanning the QR code OK, I can not be allowed to select network? Neither automatically nor manually. Can not be allowed to select the wifi box at all ??

reply | This was helpful (0) (Translated by Google)
Martin Rahn 13-09-2020
My worx m500 turns off right after I turn it on. Everything also lights up fully battery but it Slides off and turns off immediately.

reply | This was helpful (0) Read more (Translated by Google)
Kristian Bjerge 13-09-2020
I had the same problem, solved it with a firmware update with a USB connector

This was helpful (0) (Translated by Google)
Åse 10-07-2021
The light on the charging station lights up red - troubleshooting tips?

reply | This was helpful (0) (Translated by Google)
Finn Jensen 05-12-2021
My charging station is lit with a constant red light Has received several notifications with temperature too low What is cause

reply | This was helpful (0) (Translated by Google)
Anders 23-03-2022
How to do when the display shows outside the work area. The robot is inside the work area and the wire around is intact.

reply | This was helpful (0) (Translated by Google)
Anne-mette Wegge-larsen 11-05-2022
Our Worx robot has started to run outside the cord and continue to drive a bit outside the fpr cord. It probably should not be able to. It's never done that before. However, cord has been changed recently since having renovation. In addition, it only runs around and around the wire if it does not run completely outside. Do not drive across the lawn otherwise. Only outside or around.

reply | This was helpful (0) (Translated by Google)
Linda Mann 23-08-2022
The display shows a padlock in the right corner and the code cannot be set. What then can I do?

reply | This was helpful (0) (Translated by Google)
Merethe Hviid 13-05-2023
Can anyone help with a QR code for the WA3750, the QR for scanning is gone - what do I do? Thanks in advance

reply | This was helpful (0) (Translated by Google)

More about this manual

We understand that it’s nice to have a paper manual for your Worx Landroid Lawn Mower. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Worx. They might be able to provide an original manual. Are you looking for the manual of your Worx Landroid Lawn Mower in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand Worx
Model Landroid
Category Lawn Mowers
File type PDF
File size 32.92 MB

All manuals for Worx Lawn Mowers
More manuals of Lawn Mowers

Frequently Asked Questions about Worx Landroid Lawn Mower

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

How do I know when to sharpen the blades of my lawn mower? Verified

Sharp blades cleanly cut the grass. Dull blades roughly tears the grass which will quikly turn brown. If the lawn mower produces teared grass, then the blades should be sharpened or replaced.

This was helpful (2383) Read more

What is mulching? Verified

Some lawn mowers are able to mulch. Mulching finely shreds the grass and blows it back to the lawn. There the mulch functions as nutrition and protection for the grass.

This was helpful (783) Read more

I accidentally put diesel in my petrol lawn mower, what should I do? Verified

Do NOT use the lawn mower. The only option is to completely empty the tank and fill it with the right fuel.

This was helpful (715) Read more

What is the best lenght for my grass? Verified

To prevent the grass from drying out it should not be too short. It's better to mow the grass more often than to cut it too short. The optimal length it between 3 and 4 centimeter.

This was helpful (415) Read more

Can I mow grass when it's wet? Verified

It is possible, but not advisable. When grass is wet it will lump together during mowing, preventing an optimal result.

This was helpful (277) Read more

What is the right moment to mow my lawn? Verified

The best months for lawn mowing are March to October. Mowing should be done once or twice a week depending on how fast the grass grows. The best time of day to mow the grass is at the end of the afternoon and never in full sunlight. This is to prevent the grass from drying out after being cut.

This was helpful (254) Read more

At what lawn surface do I choose an electric mower and at which surface a petrol mower? Verified

For surfaces up to 300m² you can use a battery driven mower. For surfaces larger than that it is recommended to use a petrol mower.

This was helpful (202) Read more

Can I let a robot mower work in the night? Verified

It's better not to let a robot mower work in the night. Some animals, like hedgehogs, are mostly active at night. They are often not quick enough to escape from the robot mower and can get severely wounded or killed.

This was helpful (198) Read more
Manual Worx Landroid Lawn Mower

Related products

Related categories