Manual Vango Braemar 150 Awning

Manual

TENT PITCHING INSTRUCTIONS – BRAEMAR (UK)

All - in - one pitching:

 Park your vehicle in the best location on your pitch ensuring that there is at least 4.6m free space at the side where you would like to pitch your AirAway/Awning.

 Ensure that the area where the awning is being pitched is clear of sharp objects and that all door zips are closed. (We recommend laying the AirAwning fabric on a

groundsheet prior to attaching it to your caravan, as this helps prevent the fabric becoming wet & dirty. It also helps prevent damaging the fabric as the awning is fed

into the awning rail.)

 Please ensure your caravan’s rail is clean and clear of debris prior to installing the AirAwning. If required, please use an aftermarket product to reduce friction between

the kador strip and the rail during fitting and removal of the AirAwning.

 Unpack the AirAwning and position it in the required direction, with the rear attachment section facing the side of the caravan. Place the pump, pegs and other

components to one side.

 Feed the leading edge of the kador into the rear of your caravan’s rail and gently pull the AirAwning into the desired position, ensuring the roof of the AirAwning is

positioned on the horizontal part of the caravan’s awning rail. (Please only pull your AirAwning by the webbing loop at either end of the kador.)

 Peg out the rear corners of the attachment section of the AirAway/AirAwning at the base of the vehicle.

 Locate inflation points on each beam

 Remove the valve cap (figure 1)

 Insert the correct pump adaptor, which will lock onto the valve (figure 2 & 3)

 There is no need to turn the white valve button as the adaptor will move this to the correct position

 Inflate all tubes to 7psi. The tubes MUST be guided into an arch as they are inflated (figure 4)

 DO NOT OVER-INFLATE THE BEAMS

 Inflate all AirBeams to 7psi. The Vango AirBeam® pump is supplied with a pressure release valve which will release pressure if more than 7.5 - 8psi is put into the

AirBeam.

 Start with the rear AirBeam and guide into an upright position whilst it is inflating

 A small amount of air may leak from the valve when it is being inflated but this is normal

 Remove the pump adaptor as soon as the beam is at the correct psi

 Replace the valve cap to create an air tight seal (figure 5 & 6)

 Peg out the remaining poles and pegging points using pin pegs at the base of poles

 Repeat for front AirBeam

 With the doors fully zipped up, peg out the front corners of the AirAwning with the rock pegs supplied, ensuring the sides and front of the awning are taut. The

adjustable pegging points allow the pegs to be positioned in a range of places, to avoid rocks and stones in the ground. They are adjustable to allow the webbing to be

tensioned, in order to achieve a taut canvas.

 Once the 4 corners of the AirAwning have been positioned, all the other pegging points (both adjustable webbing and elastic) at the base of each door should be pegged

out, using the rock pegs supplied.

 At the base of each door is a webbing strap with 2 eyelets in it. Insert a groundsheet peg (a peg with a flat, round top) in to each of these eyelets to hold the webbing

strap close to the ground.

 Inside the AirAwning, inflate & install the "Bracer" AirBeams between the main AirBeams. The ends of these are located using hook & loop fabrics. The Bracer AirBeams

will increase the tension in the roof and will provide extra stability during poor weather.

 2 long pads are provided: these are fitted vertically between the AirAwning and the caravan, reducing draughts. They are attached using hook & loop fixings. To hold

the pads against the caravan in windier conditions, 2 adjustable steel poles are supplied. Place the flat end of these poles into the webbing sleeves at either end of the

awning, just below the outermost AirBeams. Place the lower, pointed end into one of the two eyelets in the base of the rear of the AirAwning. The length of the pole

can then be adjusted to apply tension between the top of the AirAwning and the base. Finally, attach the AirAwning fabric to the steel pole by wrapping the hook & loop

tabs around it.

 Identify the PVC wheel arch covers & draught skirt. Slide the draught skirt into place using the awning rail at the base of the caravan. The bottom of the draught skirt is

held in place with groundsheet pegs. The wheel arch covers are attached using the suckers provided. For a single axle caravan, only one of these covers will be needed.

 In extreme weather, the AirAwning may slide along the awning rail. To prevent this, attach one of the sucker hooks to the caravan, and attach the webbing loop at the

end of the kador strip into the hook.

 Webbing Straps - Remove the supplied webbing straps from the peg bag and clip into the corresponding buckles on the rear of the AirAway roof. Pass the straps over

the roof of the vehicle and peg into the ground. Adjust the straps to fully tension the roof.

 Peg out ALL guy lines using pin-pegs ensuring that guy line fabric attachment points are evenly tensioned.

 When the AirAwning is to be used in windy weather conditions, Vango recommends using the supplied storm straps

 The straps should be attached to the corresponding clips on the fillets attached to the rear AirBeam of the AirAway, and secured using the pegs supplied.

TO DEFLATE AIRBEAM/ AIRAWAY/ AIRAWNING:

 To deflate the AirBeam (remove the cap (figure 7)) press & turn (figure 8) the button from CLOSED to OPEN

In the unlikely event of a puncture:

 Deflate the air beam. Unzip the internal flysheet sleeve which contains the affected beam.

 Remove the tube and its protective outer.

 The zips for the protective outer are cable tied together to prevent accidental access. Cut the cable tie and open the zip.

 DO NOT open these zips when the tube inflated.

 Remove the clear rubberised tube from the protective sleeve taking care when removing the valve from the sleeve.

 Partially inflate the tube and pass through a bucket or basin of water, looking for air bubbles. This will indicate location of puncture

 Use the repair patch provided and cover hole, using instructions on patch. Re-insert tube into protective outer, closing zip from both ends, so that zip pullers are in the

flysheet sleeve (this might be easier with the tube partially inflated)

AIRBEAM INFLATION:

AIRBEAM DEFLATION:

Figure 1

Remove

locking cap

Figure 3

Lock locking pump

connector

Figure 4

Inflate with

AirBeam pump

Figure 5

Insert locking

cap

Figure 6

Lock locking cap

Figure 8

Push button to deflate &

twist to open position

Figure 7

Unlock

locking cap

Figure 2

Insert locking pump

connector

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Vango Braemar 150 Awning. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Vango. They might be able to provide an original manual. Are you looking for the manual of your Vango Braemar 150 Awning in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Vango Awnings
More manuals of Awnings

Frequently Asked Questions about Vango Braemar 150 Awning

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.