Home > Camping & Outdoor > Tents > Vango Tents > Vango Banshee 300 Tent

Manual Vango Banshee 300 Tent

Need a manual for your Vango Banshee 300 Tent? Below you can view and download the PDF manual for free in English. This product currently has 7 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

TENT PITCHING INSTRUCTIONS – BANSHEE 200 & 300(UK)

FLYSHEET FIRST PITCHING:

 Assemble poles and lay them parallel on the ground (2 poles – 1 long, 1 short).

 open flysheet on ground and position tent in desired direction

 Locate pole sleeves on flysheet and insert poles.

 On one side, locate the end of each pole into the corresponding eyelets on

pole anchor straps.

 On opposite side, push poles into an arch and locate pole ends into the

corresponding eyelets on pole anchor straps.

 Peg out webbing straps at both corners of one end of tent using pin pegs

supplied.

 Pull flysheet from other end, away from end pegged points, until tent takes

shape. Peg the opposite two webbing straps.

 Peg down remaining pole anchor straps and pegging points.

 Attach clips to poles

 Peg out ALL guy lines.

INNER FIRST PITCHING:

 Open out inner tent inside flysheet and position so that doorways on inner and flysheet line up

 Starting from the rear corners of the tent, attach the elasticated hooks on the groundsheet to corresponding rings on the flysheet anchor

straps. Suspend the inner by attaching elastic loops of inner tent with clips on inside of flysheet.

TENSION BAND SYSTEM:

 If necessary, insert tension bands through corresponding access points in the inner tent (ceiling and sidewall). Connect the straps into the

side-release buckles.

 Adjust the tension of the TBS straps until the slack is taken out

 Tension band pockets are provided for storage when not in use.

………………………………………………………………………………………………………………………………………………………………………………………….....

AUFBAUANLEITUNG – BANSHEE 200 & 300(DE)

MIT AUßENZELTAUFBAU ZUERST:

 Stecken Sie die Stangen zusammen und legen Sie sie parallel zueinander auf den Boden (2 Stangen - 1 lange, 1 kurze).

 Breiten Sie das Überdach auf dem Boden aus und positionieren Sie das Zelt in der gewünschten Richtung.

 Fixieren Sie die Stangenhüllen am Überdach und führen Sie die Stangen ein.

 Fixieren Sie das Ende jeder Stange an einer Seite in den dazu passenden Ösen in den Verankerungsschnüren der Stangen.

 Drücken Sie die Stangen gewölbeförmig an der gegenüberliegenden Seite hoch und fixieren Sie die Stangenenden in den dazu passenden

Ösen in den Verankerungsschnüren der Stangen.

 Stecken Sie die Verschlussbänder an beiden Ecken des einen Endes des Zelts aus, indem Sie die mitgelieferten Arretierstifte benutzen.

 Ziehen Sie das Überdach vom anderen Ende her, weg von den Befestigungspunkten, bis das Zelt Form annimmt. Befestigen Sie die

gegenüberliegenden beiden Verschlussbänder.

 Befestigen Sie die verbleibenden Verankerungsschnüre der Stangen und die verbleibenden Befestigungspunkte.

 Befestigen Sie die Clips an den Stangen.

 Spannen Sie ALLE Spannseile.

INNENZELT-ZUERST-AUFBAU:

 Breiten Sie das Innenzelt im Inneren des Überdachs aus und positionieren Sie es so, dass die Türöffnungen des Innenzelts und des Überdachs

deckungsgleich sind.

 Von den hinteren Ecken des Zeltes ausgehend, befestigen Sie die elastischen Haken an der Bodenplane mit den passenden Ringen an den

Verankerungsschnüren des Überdachs. Hängen Sie das Innenzelt ein, indem Sie die Gummibänder des Innenzelts mit Clips an der

Innenseite des Überdachs befestigen.

SPANNGURTVORRICHTUNG:

 Falls notwendig, ziehen Sie die Spannungsschnüre durch die zugehörigen Zugangspunkte im Innenzelt (Decke und Seitenwand). Verbinden

Sie die Schnüre mit den seitlichen Freigabespangen.

 Passen Sie die Spannung der TBS-Schnüre an, bis das Zelt gespannt ist.

 Taschen für die Spannschnüre werden zum Verstauen der nicht gebrauchten Bänder mitgeliefert

INSTRUCTIONS DE MONTAGE – BANSHEE 200 & 300(FR)

MONTAGE EN COMMENÇANT PAR LE DOUBLE TOIT:

 Réunir les arceaux et les poser parallèlement au sol (2 arceaux – 1 long, 1 court).

 Ouvrir le double toit sur le sol et positionner la tente dans la direction désirée.

 Placer les fourreaux d'arceau sur le double toit et y insérer les arceaux.

 D'un côté, placer l'extrémité de chaque arceau à l'intérieur des oeillets correspondants, sur les bandes d'ancrage des arceaux.

 Du côté opposé, pousser les arceaux à l'intérieur d'une arche et placer les extrémités des arceaux dans les oeillets correspondants, sur les

bandes d'ancrage des arceaux.

 Fixer les sangles aux deux coins d'une des extrémités de la tente, à l'aide des piquets fournis.

 Tirer le double toit depuis l'autre extrémité, à l'opposé des points de fixation, jusqu'à ce que la tente prenne sa forme. Attacher les deux

sangles à l'opposé.

 Fixer au sol les bandes d'ancrage d'arceau, restant libres et les points de fixation.

 Attacher les clips aux arceaux.

 Attacher TOUTES les cordes de tension.

MONTAGE EN COMMENÇANT PAR LA TENTE INTÉRIEURE:

 Ouvrir la tente intérieure, à l'intérieur du double toit et positionner la porte, pour qu'elle soit alignée avec celle du double toit.

 En commençant par les coins arrière de la tente, attacher les crochets munis d'élastiques, placés sur le tapis de sol, aux anneaux

correspondants, placés sur les bandes d'ancrage du double toit. Suspendre la tente intérieure en attachant les sangles élastiques de la

tente intérieure aux clips placés à l'intérieur du double toit.

ENSEMBLE DES SANGLES DE TENSION:

 Si nécessaire, insérer des bandes de serrage au niveau des points d'accès correspondants, dans la tente intérieure (plafond et paroi

murale). Attacher les sangles aux boucles détachables automatiques.

 Ajuster la tension des sangles TBS, jusqu'à ce que le flottement ait disparu.

 Des pochettes réservées aux bandes de tension sont fournies pour le rangement, lorsqu'elles ne sont pas utilisées.

Rating

Let us know what you think about the Vango Banshee 300 Tent by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Vango Banshee 300 Tent?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Vango Banshee 300 Tent. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Vango Banshee 300 Tent. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Vango. They might be able to provide an original manual. Are you looking for the manual of your Vango Banshee 300 Tent in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand	Vango
Model	Banshee 300
Category	Tents
File type	PDF
File size	0.13 MB

All manuals for Vango Tents
More manuals of Tents

Frequently Asked Questions about Vango Banshee 300 Tent

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Can I store my tent when it's wet? Verified

Only for very short periods of time. When a tent is stored while wet for a week or longer, it can get moldy. This is harmful for your tent and possibly your health.

This was helpful (384) Read more

How do I impregnate a tent? Verified

Pitch the tent, clean the cloth and let it dry. Apply the impregnation agent on the cloth with a plant sprayer or other spray. It is also possible to use a paint roller or brush. The cloth needs to be fully saturated with the impregnation agent. Also treat the inside of the tent. Thoroughly clean any windows with a moist cloth. Do not let the impregnation agent dry on it. Let the tent cloth fully dry. Repeat the treatment if needed.

This was helpful (285) Read more

Can I repair a tear or hole in the canvas of my tent myself? Verified

There are special pieces of self-adhesive patches of cloth available for synthetic tent canvases. Stick one of these patches on both sides of the hole or tear. For cotton tent canvases or mixed material tent canvases it's best to use patches that can be ironed on. This will require an iron.

This was helpful (218) Read more

The zipper of my tent won't run smoothly, what can I do? Verified

When a zipper is running smoothly, use a dry PTFE spray or silicone spray. Do not spray onto the cloth and preventively spray to prevent future problems.

This was helpful (156) Read more

There are water drops on the inside of the tent, does this mean it is leaking? Verified

No, this is probably condensation. Make sure the tent is properly ventilated to keep condensation at a minimum.

This was helpful (129) Read more

What tent pegs are best to use for which surfaces? Verified

On grassland or forest surfaces you can use semi circular or plastic pegs. On rocky surfaces you need to use rock pegs. On clay surfaces you can use semi circular, plastic or universal pegs. On gravel surfaces you need semi circular or universal pegs and on sand you need to use wooden pegs.

This was helpful (105) Read more

The impregnation agent leaves white stains or a white haze on the tent cloth, what can I do about this? Verified

If the agent leaves a white haze or white stains on the tent cloth, this means you have applied more impregnation agent on those areas. This is not harmful and the stains often disappear over time. It is not advisable to use less impregnation agent to prevent stains. The cloth needs to be fully saturated with the impregnation agent to give good results.

This was helpful (97) Read more