Home > Do-It-Yourself > Belt Sanders > Trotec Belt Sanders > Trotec PBSS 10-600 Belt Sander

Manual Trotec PBSS 10-600 Belt Sander

Need a manual for your Trotec PBSS 10-600 Belt Sander? Below you can view and download the PDF manual for free in English. This product currently has 4 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

EN 15

belt sander PBSS 10-600

Shutdown

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• If required, allow the device to cool down.

• Remove the tool from the device (see Start-up chapter).

• If attached, disconnect the dust extraction system from the

device.

• Clean the device according to the Maintenance chapter.

• Store the device according to the Storage chapter.

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

Troubleshooting tasks which require the housing to be opened

must only be carried out by an authorized specialist electrical

company or by Trotec.

Light smoke or odour is emitted during the first use:

• This is not a fault. These phenomena disappear after a

brief runtime.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damages. If you

notice damages, do not try to take the device back into

operation. To avoid safety hazards, do not perform any

repairs. Send the device to a specialist electrical company

or to Trotec to have the power cable and mains plug

replaced.

• Check the on-site fusing.

Info

Wait for at least 10 minutes before switching the

device back on.

The abrasive belt does not move although the motor is

running:

• Make sure that the abrasive belt does not grind into the

housing. Adjust the belt run if required, see chapter

Adjusting the belt run.

• Make sure that there is no workpiece debris blocking the

drive. Remove the blockages, if any.

• Check whether you are using an abrasive belt that is

suitable for this device.

The motor slows down:

• Check whether the device is overloaded by the workpiece.

• Reduce the pressure applied on the workpiece.

• Check whether the workpiece is suitable for the tasks to

be carried out.

The surface of the workpiece is not smooth or the grinding

performance is insufficient:

• Check whether the selected abrasive belt is suitable for the

material to be processed.

• If the abrasive belt is worn, replace it with a new one, see

chapter Changing the abrasive belt.

• Check the belt speed setting. It must be suitable for both

the abrasive belt and the material.

• Select a higher speed level by turning the setting wheel for

the belt speed selection to the desired level.

The device becomes hot:

• Check whether the selected abrasive belt is suitable for the

tasks to be carried out.

• Make sure not to exert too much pressure on the device

during grinding.

• Keep the venting slots clear to prevent the motor from

overheating.

• Wait for at least 10 minutes before switching the device

back on.

Your device still does not operate correctly after these

checks?

Please contact the customer service. If necessary, bring the

device to an authorized specialist electrical company or to

Trotec for repair.

Maintenance

Activities required before starting maintenance

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Allow the device to cool down completely.

Warning of electrical voltage

Maintenance tasks which require the housing to be

opened must only be carried out by authorised

specialist companies or by Trotec.

Notes on maintenance

Inside the device, there are no parts that need to be maintained

or lubricated by the user.

Rating

Let us know what you think about the Trotec PBSS 10-600 Belt Sander by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Trotec PBSS 10-600 Belt Sander?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Trotec PBSS 10-600 Belt Sander. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Trotec PBSS 10-600 Belt Sander. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Trotec. They might be able to provide an original manual. Are you looking for the manual of your Trotec PBSS 10-600 Belt Sander in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand	Trotec
Model	PBSS 10-600
Category	Belt Sanders
File type	PDF
File size	2.25 MB

All manuals for Trotec Belt Sanders
More manuals of Belt Sanders

Frequently Asked Questions about Trotec PBSS 10-600 Belt Sander

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Do I need to wear hearing protection when using a sander? Verified

Yes you should. Although the amount of noise produced by a sander can vary between brands and models, long term exposure to loud noise can cause permanent hearing damage. That is why it is a good idea to wear hearing protection.

This was helpful (9) Read more

Do I need to wear eye protection when using a sander? Verified

Yes. Small particles can fly up during sanding. When these hit an eye they can cause permanent eye damage. That is why it always necessary to wear eye protection.

This was helpful (8) Read more

Do I need to wear a dust mask when using a sander? Verified

Yes. Dust is released during sanding which can cause respiratory damage. Some surfaces can also release chemicals like paint or varnish during sanding. These are also a good reason to wear a dust mask.

This was helpful (7) Read more

Can I store power tools in a shed or garage? Verified

In general, you can store power tools in a shed or garage, even if it sometimes freezes there. However, it is better for the lifespan of the power tool to store it in a dry place without major temperature fluctuations. In a shed or garage, differences in temperature can cause condensation to form, which can cause rust. In addition, tools that run on batteries last shorter and do not charge as well at very low temperatures. To be sure how your power tool needs to be stored, always thoroughly read the user manual.

This was helpful (2) Read more