Home > Audio, TV & Photo > Remote Controls > Thomson Remote Controls > Thomson ROC550 Remote Control

Manual Thomson ROC550 Remote Control

Need a manual for your Thomson ROC550 Remote Control? Below you can view and download the PDF manual for free in English. This product currently has 6 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

3 - Programming the remote control

Method A – Fast programming with 1-digit subcode

Method B – 3-digit codes programming

Before you start programming, you must find the subcode of the set to be controlled

(Television, VCR, satellite receiver, cable receiver or DVD player).

Refer to the list provided with these instructions, page I of the subcodes.

1. Switch on the set you want to control.

2. Hold down the S (6) key until the key that corresponds to the last mode you selected

blinks 3 times and then remains lit (the indicator light remains on for a few seconds

to give you the time to proceed with the following steps. The indicator lamp flashes

to signal that this time is almost up, and then goes off).

3. Press the key (15) that corresponds to the type of equipment you want to control:

TV: television set, VCR: video recorder, SAT: satellite receiver,

DVD: DVD player, AUX: other set

4. While the indicator is lit

, type in the subcode (example: 1 for THOMSON).

5. Direct the remote control towards the set and try to switch it off by pressing the

key

(17).

6. If the set you want to control switches off, press OK (2) to memorise the subcode.

7. Should the set not switch off, press key

(17) repeatedly, until the set switches off.

Between two key pr

esses, leave enough time for the key corresponding to the selected

mode enough time to light up again (about 1 second). Proceeding this way will

enable you to see whether the set responds or not.

8. Immediately

upon the switching-off of the set to be controlled, press OK (2) to store

the subcode.

Note

When programming the

AUX

key or if you want to assign another type of set than those

mentioned on the remote control, for example a satellite code in

VCR

mode, begin by

entering a code that corresponds to the set you want to programme (a 3-digit code that

you will find in the code booklet, see method

B). Then begin the automatic search

(method D).

Example: if you want to control a satellite receiver with the

AUX

key, begin by entering

a satellite code (any satellite code that you find in the code list, for example: 603 for a

Thomson satellite receiver) then begin the automatic search procedure. The remote

control will then test all the satellite codes for the selected make.

Check of the programming:

In principle, your set is ready for receiving the remote control commands.

Check your remote control for proper functioning by performing the test described on

page 4.

Before you start programming, you must find the code of the set to be controlled

(Television, VCR, satellite receiver, cable receiver or DVD player).

Refer to the list provided with these instructions, page II of the codes.

1. Switch on the set you want to control.

2. Hold down the S (6) key until the key that corresponds to the last mode you selected

blinks 3 times and then remains lit (the indicator light remains on for a few seconds

to give you the time to proceed with the following steps. The indicator lamp flashes

to signal that this time is almost up, and then goes off).

3. Press the key (15) that corresponds to the type of equipment you want to control:

TV: television set, VCR: video recorder, SAT: satellite receiver,

DVD: DVD player, AUX: other set

4. While the indicator is lit

, enter the first digit of the 3-digit code proposed for the set

to be controlled (example: 036 for Thomson).

5. Direct the remote control towards the set and try to switch it off by pressing the

key

(17).

6. Should the set not switch off, repeat step 2. Then type in the next 3-digit code. Try to

switch off the set by pressing key

(17) once. Repeat this procedure by trying out

each of the 3-digit codes.

Check of the pr

ogramming:

In principle, your set is ready for receiving the remote control commands.

Check your remote control for proper functioning by performing the test described on

page 4.

ROC 550 GB 18/07/02 10:36 Page 2

Rating

Let us know what you think about the Thomson ROC550 Remote Control by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Thomson ROC550 Remote Control?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Thomson ROC550 Remote Control. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Thomson ROC550 Remote Control. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Thomson. They might be able to provide an original manual. Are you looking for the manual of your Thomson ROC550 Remote Control in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand	Thomson
Model	ROC550
Category	Remote Controls
File type	PDF
File size	1.65 MB

All manuals for Thomson Remote Controls
More manuals of Remote Controls

Frequently Asked Questions about Thomson ROC550 Remote Control

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

How do I connect a universal remote control to my television? Verified

To connect your universal remote control, you need the model number and brand name of both the remote control and the television. There is a list of codes for brands and model numbers in the manual of the remote control .

This was helpful (7324) Read more

Why are there letters next to the numbers on the remote control? Verified

Certain television settings may require you to enter letters. There are usually three letters or other characters on a button. When letter input is required, you can press that button once for the first letter, press twice for the second letter and press 3 times for the third letter. This way, text can be written with a minimum number of buttons.

This was helpful (588) Read more

Will my remote control also work on other television models of the same brand? Verified

Often a remote control of a television will also work on similar models of the same brand. However, it is unusual that it will work on all models of that brand. Universal remote controls are more suited to do this.

This was helpful (424) Read more

What is the average range of an infrared remote control? Verified

An average infrared remote control had a range of around 3 to 6 meters. Also, the further away the device is, the harder it will be to aim.

This was helpful (363) Read more

A battery in my device is oxidized, can I still safely use it? Verified

Ja, the device can still be safely used. Firstly, remove the oxidizd battery. Never use bare hands to do this. Then clean the battery compartment with a cotton swab dipped in vinegar or lemon juice. Let it dry and insert new batteries.

This was helpful (263) Read more

Can I leave a replacable battery in a device for a long time? Verified

Replacable batteries can remain in a device for a long time if the device is in use. When a device is being stored for a long time it is advisable to remove the batteries to prevent oxidation.

This was helpful (209) Read more