Manual Sun Joe SPX3000 Pressure Washer

Manual

mWARNING! Water that has own through backow

preventers is considered to be non-potable.

mWARNING! During cleaning, maintenance or when

replacing parts, the machine must be disconnected from its

power source by removing the plug from the socket outlet.

mWARNING! High pressure hoses, ttings, and couplings

are important for the safe operation of the appliance. Use

only hoses, ttings, and couplings recommended by the

manufacturer.

• Check for damaged parts – Do not use the appliance if the

supply cord or other important parts of the appliance are

damaged (e.g. safety devices, high pressure hoses, trigger

gun).

mWARNING! If an extension cord is used, the plug and

socket must be of watertight construction.

mWARNING! Inadequate extension cords can be

dangerous.

• This high pressure washer must not be used at

temperatures below 32ºF (0°C).

mWARNING! Power cords on drums should always be

completely unwound to prevent the cord from overheating.

• Power cord connections should be kept dry and off the

ground.

• Comply with the below requirements for length and cord

specs (Table 1):

• If the power cord is damaged, it must be replaced by the

manufacturer or his service agent or similarly qualied

person in order to avoid a hazard.

• Keep the machine on a stable, at surface during operation,

handling, transportation, and storage. Sudden overturn of

the machine can cause bodily injury.

• In the event of an accident or breakdown, switch off the

machine immediately. (If contact with detergent occurs,

rinse with an abundance of clean water.)

Electrical Safety

ATTENTION: If there are problems with the electrical

MAINS, short voltage drops may appear when starting the

equipment. This can, in turn, inuence other equipment (e.g.

cause a lamp to blink). If the MAINS-IMPEDANCE Zmax <

0.335 OHM, such disturbances are not expected. (In case

of assistance, contact your local supply authority for further

information.)

mWARNING! Electrical Shock Hazard

Before starting up your machine, please check it carefully for

any defects. If you nd any, do not start up your machine and

contact your distributor.

The following should be observed when connecting the high

pressure washer to the electric installation:

• The electric supply connection should be performed by a

qualied person.

• The electric supply to this appliance should include either

a residual current device that will interrupt the supply if the

leakage current to the earth exceeds 30 mA for 30 ms or a

device that will interrupt the earth circuit (GFCI).

IMPORTANT: Only use water without any impurities.

If there is a risk of running sand into the inlet water (i.e. from

your own well), an additional lter should be installed.

Safety devices

The unloader valve can reduce pressure if it exceeds preset

values. The spray gun features a locking device. When the lock

is activated, the spray gun cannot be operated.

• Thermal sensor – A thermal sensor protects the motor

against overloading. The machine will restart after a few

minutes when the thermal sensor has cooled.

• Double insulation – In a double-insulated product, two

systems of insulation are provided instead of grounding.

No grounding means are provided on a double-insulated

product, nor should a means for grounding be added to

the product. Servicing a double-insulated product requires

extreme care and knowledge of the system, and should be

performed only by a qualied service person. Replacement

parts for a double-insulated product must be identical to the

parts they replace. A double-insulated product is marked

with the words “DOUBLE INSULATION” or “DOUBLE

INSULATED”. The symbol “

” may also be marked on the

product.

• Ground Fault Circuit Interrupter (GFCI) – This pressure

washer is provided with a ground-fault circuit-interrupter

(GFCI) built into the plug of the power-supply cord. This

device provides additional protection from the risk of

electric shock. Should replacement of the plug or cord

become necessary, use only identical replacement parts

that include GFCI protection.

Table 1

25

18

18

16

50

16

16

16

100

16

14

150

14

12

Volts

120V

0 – 6

6 – 10

10 – 12

Total length of cord in feet

AWG

Not Recommended

Ampere Rating

More than

Not more than

2

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Sun Joe SPX3000 Pressure Washer. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Sun Joe. They might be able to provide an original manual. Are you looking for the manual of your Sun Joe SPX3000 Pressure Washer in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Sun Joe Pressure Washers
More manuals of Pressure Washers

Frequently Asked Questions about Sun Joe SPX3000 Pressure Washer

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Sun Joe SPX2000 Pressure Washer

Manual

Sun Joe SPX1000 Pressure Washer

Manual

Parkside PHD 170 C2 Pressure Washer

Manual

Husqvarna PW 490 Pressure Washer

Manual

Cecotec HidroBoost 1600 Car&Bike Pressure Washer

Manual

Vonroc PW506AC Pressure Washer

Manual

Vito VIML150HQA Pressure Washer

Manual

Parkside PHD 135 D5 Pressure Washer

Related categories