Manual Sony M-570V Cassette Recorder
Need a manual for your Sony M-570V Cassette Recorder? Below you can view and download the PDF manual for free in English. This product currently has 0 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.
Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.
Manual
Loading…
2-593-807-53 (1)
Operating Instructions
Mode d’emploi (au verso)
M-575V/570V/475/470
Microcassette™-Corder
House current
AC power adaptor
(not supplied)
to the mains
Connect the AC power adaptor to DC IN 3V and to the mains.
Use a commercially-available AC power adaptor (rated output voltage/
current: 3 V DC/700 mA).
Do not use any other AC power adaptor.
Polarity of the plug
Notes
Depending on the AC power adaptor, noise may be heard while using the unit.
Refer to the operating instructions of the AC power adaptor.
The voltage of power supply is different depending on the country. Please buy
an AC power adaptor in the country where the product is to be used.
Do not touch the AC power adaptor with wet hands.
Connect the AC power adaptor to an easily accessible mains. Should you notice
an abnormality in the AC power adaptor, disconnect it from the mains
immediately.
Recording
You can record right away with the built-in microphone.
PAUSE
EAR
VOR (M-575V/
570V only)
Microphone
FF/CUE •
REW/REVIEW
* The button/switch has a tactile dot.
Tape counter
(M-575V/570V only)
REC/BATT (M-575V/
570V)
BATT (M-475/470)
VOL*
Tape counter reset
button (M-575V/
570V only)
TAPE SPEED*
1 Press the reset button of the tape counter (M-575V/570V only).
2 Press and insert a standard microcassette with the side to
start recording facing the lid.
3 Select the desired tape speed.
2.4 cm for optimum sound (recommended for normal use): A 30-
minute recording can be made using both sides of the MC-30
microcassette (for supplied accessories, see “Specifications”). There
is a tactile dot on this side.
1.2 cm for longer recording time: A 60-minute recording can be
made using both sides of the MC-30 microcassette (for supplied
accessories, see “Specifications”).
4 Set VOR to OFF (M-575V/570V only).
If you set VOR to ON, the unit automatically starts recording the
sound and pauses when there is no sound (you can save tapes and
batteries).
When the sound is not loud enough, set it to OFF, or the unit may
not start recording.
5 Press .
is pressed simultaneously and recording starts.
While the tape runs, the REC/BATT lamp lights and flashes
depending on the strength of the sound (M-575V/570V only).
Recording level is fixed.
At the end of the tape, recording stops and the unit turns off
automatically (Automatic shut-off mechanism).
To Press or slide
Stop recording
Pause recording
Slide
PAUSE in the direction of the arrow.
To release pause recording, release
PAUSE*.
Start recording during
playback
during playback (the unit enters the recording
mode)
Review the portion just
recorded
Push up FF/CUE
•
REW/REVIEW toward
REW/REVIEW during the recording. Release the
button at the point to start playback.
Take out a cassette
*
PAUSE will also be automatically released when
is pressed (stop-
pause-release function).
Note
Select the 2.4 cm tape speed for recording, if you play back the recorded tape with
another unit. Otherwise, the sound quality may be changed.
Notes on VOR (Voice Operated Recording) (M-575V/570V only)
The VOR system is affected by the environmental recording conditions. When
you use the system in a noisy place, the unit will stay in the recording mode. If
the sound is too soft, on the contrary, the unit will not start recording. If you
cannot get the results you want, set it to OFF.
The VOR system may not record the beginning of the sound you want to record
because it starts recording only after it catches the sound. For an important
recording, set it to OFF.
To monitor the sound
Connect an earphone (not supplied) firmly to the EAR jack. The
monitor volume cannot be adjusted by VOL.
To prevent a cassette from being accidentally recorded over
Break off and remove the cassette tabs. To reuse the cassette for
recording, cover the tab hole with adhesive tape.
Playing a Tape
VOL*
*
PAUSE
FF/CUE •
REW/REVIEW
EAR
* The button/switch has a tactile dot.
TAPE SPEED*
REC/BATT (M-575V/
570V)
BATT (M-475/470)
1 Insert a cassette with the side to start playing facing the lid.
2 Select the tape speed to the same speed as that used for recording.
3 Press .
4 Turn VOL to adjust the volume. There is a tactile dot beside VOL on
to show the direction to turn up the volume.
At the end of the tape, playback stops and the unit turns off
automatically (Automatic shut-off mechanism). After the tape has been
wound or rewound, be sure to press .
If you plug in headphones (not supplied) to the EAR jack, you will get
monaural output from both left and right channels.
To Press or slide
Stop playback/stop fast
forward or rewind
Pause playback
Slide
PAUSE in the direction of the arrow. REC/
BATT (M-575V/570V) or BATT (M-475/470) lamp
goes off.
To release pause playback, release
PAUSE*.
Fast forward** (FF)
Slide FF/CUE
•
REW/REVIEW toward FF/
CUE
during stop.
Rewind** (REW)
Slide FF/CUE
•
REW/REVIEW toward
REW/REVIEW during stop.
Search forward during
playback (CUE)
Keep FF/CUE
•
REW/REVIEW pushed
toward FF/CUE
during playback and release it at
the point you want.
Search backward during
playback (REVIEW)
Keep FF/CUE
•
REW/REVIEW pushed
toward
REW/REVIEW during playback and
release it at the point you want.
Start recording during
playback
*
PAUSE will also be automatically released when
is pressed (stop-
pause-release function).
** If you leave the unit after the tape has been wound or rewound, the batteries
will be consumed rapidly. Be sure to press
.
Note
If the tape is completely rewound while searching backward during playback
(REVIEW), the FF/CUE
•
REW/REVIEW switch may not return to the
center position when you release the switch. In this case, push back the switch to
the center to start playback.
Precautions
On power
Operate the unit only on 3 V DC.
For AC operation, use the AC power adaptor recommended for the
unit. Do not use any other type. For battery operation, use two R03
(size AAA) batteries.
On the unit
Use only the (standard microcassettes) with this unit.
Non-standard cassettes cannot be used because their “L” dimension
(see illustration) is different.
Approx. 5 mm
Standard
Only standard microcassettes
have a small indention of side A.
Approx. 2.5 mm
Non-standard
Do not leave the unit in a location near heat sources, or in a place
subject to direct sunlight, excessive dust or mechanical shock.
Should any solid object or liquid fall into the unit, remove the
batteries or disconnect the AC power adaptor, and have the unit
checked by qualified personnel before operating it any further.
Keep personal credit cards using magnetic coding or spring-wound
watches, etc. away from the unit to prevent possible damage from the
magnet used for the speaker.
When you do not use the unit for long, remove the batteries to avoid
damage caused by battery leakage and subsequent corrosion.
If the unit has not been used for long, set it in the playback mode and
warm it up for a few minutes before inserting a cassette.
If you have any questions or problems concerning your unit, please
consult your nearest Sony dealer.
Troubleshooting
Should any problem persist after you have made these checks, consult
your nearest Sony dealer.
You cannot close the cassette compartment lid.
The cassette is being inserted in the wrong way.
has been already pressed.
The cassette is not being inserted completely.
The unit does not operate.
The batteries have been inserted with incorrect polarity.
The batteries are weak. Replace both batteries with new ones.
PAUSE is slid in the direction of the arrow.
The AC power adaptor is not firmly connected.
The unit will not run on dry batteries if the AC power adaptor is
left plugged into the DC IN 3V jack even though you disconnect
the AC power adaptor from the power source.
Recording cannot be made.
There is no cassette in the cassette compartment.
The tab on the tape has been removed. To reuse the tape for
recording, cover the tab hole with adhesive tape.
The batteries are weak. Replace both batteries with new ones.
Recording is interrupted.
The VOR switch is set to ON. When you do not use VOR, set it
to OFF (M-575V/570V only).
Recording cannot be erased completely.
The head is contaminated. See “Maintenance”.
Playback cannot be made.
The tape has reached the end. Rewind the tape.
No sound comes from the speaker.
The earphone is plugged in. Unplug it.
The volume is turned down completely.
The sound drops out or comes with excessive noise.
The volume is turned down completely.
The batteries are weak. Replace both batteries with new ones.
The head is contaminated. See “Maintenance”.
Direct placement of the cassette tape on the speaker resulted in
magnetization and deteriorated tonal quality.
Use the unit away from radiowave-emitting devices such as
cellular phones.
WARNING
To prevent fire or shock hazard, do not expose
the unit to rain or moisture.
Disposal of Old Electrical & Electronic Equipment (Applicable in
the European Union and other European countries with separate
collection systems)
This symbol on the product or on its packaging indicates
that this product shall not be treated as household waste.
Instead it shall be handed over to the applicable
collection point for the recycling of electrical and
electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling of this product. The
recycling of materials will help to conserve natural
resources. For more detailed information about recycling
of this product, please contact your local city office, your
household waste disposal service or the shop where you
purchased the product.
About This Manual
The instructions in this manual are for 4 models. The M-570V is the
model used for illustration purposes.
Their differences are shown in the table below:
M-575V/570V M-475/470
Tape counter
—
BATT lamp —
REC/BATT lamp
—
VOR
—
: provided or supplied
—: not provided or not supplied
There is no difference between M-575V and M-570V and between M-475
and M-470 except for the supplied accessories.
M-575V consists of M-570V Microcassette recorder and accessories.
For information about the supplied accessories, see “Specifications” of this
manual.
Preparing Power Sources
Choose one of the following power sources.
Dry Batteries
Insert the batteries
with correct polarity.
Make sure that nothing is connected to the DC IN 3V jack.
1 Open the battery compartment lid.
2 Insert two R03 (size AAA) batteries with correct polarity and close
the lid.
To take out the batteries
To attach the battery compartment lid if it is accidentally
detached
When to replace the batteries
Replace the batteries with new ones of the same kind when the REC/
BATT (M-575V/570V) or BATT (M-475/470) lamp dims.
Notes
The unit will play back normally for a while, even after the REC/BATT (M-
575V/570V) or BATT (M-475/470) lamp flashes. However, replace the batteries
as soon as you can. Otherwise, the built-in speaker may emit a loud noise and
recordings may not be made correctly.
In the following cases you do not need to replace the batteries:
– if the REC/BATT (M-575V/570V) or BATT (M-475/470) lamp flashes with
the playback sound when you turn up the volume.
– if the REC/BATT (M-575V/570V) or BATT (M-475/470) lamp lights
momentarily when the tape starts running or at the end of the tape.
– if the REC/BATT (M-575V/570V) or BATT (M-475/470) lamp flashes during
FF/REW or CUE/REVIEW.
Battery life* (Approx. hours)
Batteries M-575V/570V M-475/470
Recording Playback** Recording Playback**
Sony alkaline
LR03 (SG)***
17 9.5 17 10
Sony manganese
R03 (SB)
6.5 3.0 6.5 3.5
* Measured valued by the standard of JEITA (Japan Electronics and Information
Technology Industries Association) (Using a Sony Microcassette)
** Using a tape on which music has been recorded is played at volume setting 7
using speaker
*** When using Sony LR03 (SG) alkaline dry batteries (produced in Japan)
Note
The battery life may be shorter depending on the operating condition, the
surrounding temperature and battery type.
For maximum performance we recommend that you use alkaline
batteries.
Tape speed is too fast or too slow or the sound is distorted in the
playback mode.
Improper setting of the TAPE SPEED switch. Set it to the same
speed as that used for recording.
The batteries are weak. Replace both batteries with new ones.
During CUE/REVIEW the tape stops or does not run.
You cannot fast-forward or rewind.
The batteries are weak. Replace both batteries with new ones.
Maintenance
Head
Pinch roller
Capstan
To clean the tape head and path
Press
and wipe the head, capstan and the pinch roller with a cotton
swab, moistened with alcohol every 10 hours of use.
To clean the exterior
Use a soft cloth slightly moistened in water. Do not use alcohol, benzine
or thinner.
Specifications
Tape
(normal position type)
Recording system
2-track 1-channel monaural
Speaker
Approx. 3.6 cm dia.
Tape speed
2.4 cm/s, 1.2 cm/s
Frequency range
300 Hz - 4 000 Hz (with TAPE SPEED switch at 2.4 cm/s)
Output
Earphone jack (minijack/monaural) for 8 Ω - 300 Ω earphone
Power output (at 10% harmonic distortion)
M-575V/570V: 450 mW
M-475/470: 250 mW
Power requirements
3 V DC batteries R03 (size AAA) × 2/External DC 3V power sources
Dimensions (w/h/d) (incl. projecting parts and controls)
M-575V/570V: Approx. 60.2 × 110.8 × 23.2 mm
M-475/470: Approx. 60.2 × 110.8 × 22.3 mm
Mass (main unit only)
M-575V/570V: Approx. 104 g
M-475/470: Approx. 97 g
Supplied accessories
Microcassette tape MC-30 (1) (M-570V/470 for the United States and Europe
only, M-475 for Europe, Asia, Central and South America and the Middle
and Near East only)
Microcassette tapes MC-30 (2) (M-470 for Canada only)
Microcassette tapes MC-30 (3) (M-575V for Canada and Europe only and M-
475 for the United States only)
Batteries (2) (M-570V for the United States only, M-575V for Canada and
Europe only, M-470 for the United States and Canada only and M-475 for the
United States and Europe only)
Design and specifications are subject to change without notice.
©2005 Sony Corporation Printed in China
Loading…
Rating
Let us know what you think about the Sony M-570V Cassette Recorder by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.More about this manual
We understand that it’s nice to have a paper manual for your Sony M-570V Cassette Recorder. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Sony. They might be able to provide an original manual. Are you looking for the manual of your Sony M-570V Cassette Recorder in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.
Specifications
| Brand | Sony |
| Model | M-570V |
| Category | Cassette Recorders |
| File type | |
| File size | 1.09 MB |
All manuals for Sony Cassette Recorders
More manuals of Cassette Recorders
Join the conversation about this product
Here you can share what you think about the Sony M-570V Cassette Recorder. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.