Home > Do-It-Yourself > Drill Bit Sharpeners > Sealey Drill Bit Sharpeners > Sealey SMS01 Drill Bit Sharpener

Manual Sealey SMS01 Drill Bit Sharpener

Need a manual for your Sealey SMS01 Drill Bit Sharpener? Below you can view and download the PDF manual for free in English. This product currently has 1 frequently asked question, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

INSTRUCTIONS FOR

DRILL BIT SHARPENER GRINDING

ATTACHMENT

MODEL NO: SMS01

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

 WARNING! Disconnect the grinder from the mains power, and ensure the grinding wheels are at a standstill before attempting to

position drill bit.

9 Maintain the sharpener in good condition.

9 Replace or repair damaged parts. Use recommended parts only. Non-authorised parts may be dangerous and will invalidate the warranty.

▲ DANGER! DO NOT use a damaged grinding wheel, to sharpen drill bits.

9 Ensure that the correct grinding wheel is used for sharpening of drill bits.

 WARNING! Keep all guards and holding screws in place, tight and in good working order. Check regularly for damaged parts.

A guard or any other part that is damaged should be repaired or replaced before tool is next used. The eye shields are a mandatory

fitting when grinder is used in premises covered by the Health & Safety at Work Act.

9 Ensure adequate lighting.

9 Before each use check grinding wheels for condition. If worn or damaged replace immediately.

 WARNING! Always wear approved eye or face protection when operating a grinder.

9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

9 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.

9 Keep children and unauthorised persons away from the working area.

8 DO NOT use the sharpener for a task it is not designed to perform.

8 DO NOT operate the grinder if any parts are damaged or missing as this may cause failure and/or personal injury.

8 DO NOT switch on the grinder whilst the wheel is in contact with the drill bit.

8 DO NOT use grinder where there are flammable liquids, solids or gases, such as paint solvents and including waste wiping or cleaning rags

etc.

8 DO NOT touch the drill bit close to the ground surface as it will be very hot. Allow to cool. The drill bit may also be very sharp.

8 DO NOT sharpen drill bits when you are tired, under the influence of alcohol, drugs or intoxicating medication.

9 When not in use switch off the grinder, disconnect from the mains power supply and clean the machine and working area.

2. INTRODUCTION

Ideal for use with any standard bench grinder, the grinding attachment provides quick and precise sharpening of 3-19mm (1/8-3/4”) HSS twist

drill bits with a 75mm minimum length. Features an angle gauge with pre-sets at 41° (Countersink), 49°, 59°, 68° and 88°. Also features a

rotating neck which aids grinding both sides of the drill bit. Perfect for use in any workshop or garage.

3. SPECIFICATION

Model No: ................................................................... SMS01

Sizes: ........................................................ 3-19mm (1/8-3/4”)

Angle Adjustment: .........41° (Countersink), 49°, 59°, 68°, 88°

Minimum Drill Bit Length: ............................................. 75mm

4. ASSEMBLY

4.1.  Thejigmustbesecurelyxedinpositionusingabolt,

washers and nut. Varying positions in relation to the

grinding wheel can be obtained using the slot in the

 base.(g1)

4.2. The jig must be positioned so that the top of the trough

can be brought to the face of the wheel.

SMS01 | Issue 1 20/12/17

Original Language Version

Refer to

instructions

g.1

Wear eye

protection

Wear a mask

Wear ear

protection

Wear safety

footwear

Rating

Let us know what you think about the Sealey SMS01 Drill Bit Sharpener by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Sealey SMS01 Drill Bit Sharpener?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Sealey SMS01 Drill Bit Sharpener. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Sealey SMS01 Drill Bit Sharpener. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Sealey. They might be able to provide an original manual. Are you looking for the manual of your Sealey SMS01 Drill Bit Sharpener in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand	Sealey
Model	SMS01
Category	Drill Bit Sharpeners
File type	PDF
File size	0.8 MB

All manuals for Sealey Drill Bit Sharpeners
More manuals of Drill Bit Sharpeners

Frequently Asked Questions about Sealey SMS01 Drill Bit Sharpener

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Can I store power tools in a shed or garage? Verified

In general, you can store power tools in a shed or garage, even if it sometimes freezes there. However, it is better for the lifespan of the power tool to store it in a dry place without major temperature fluctuations. In a shed or garage, differences in temperature can cause condensation to form, which can cause rust. In addition, tools that run on batteries last shorter and do not charge as well at very low temperatures. To be sure how your power tool needs to be stored, always thoroughly read the user manual.

This was helpful (2) Read more