Inserting/Removing the Memory Card
Important! In order to use SDXC memory cards with Windows XP, an update
of Windows XP is required. Only then will the „exFat“ file system of SDXC
memory cards be supported. You can download the update at www.micro-
soft.com. To find the update, e.g. enter the search terms „exfat windows xp“
in the search bar of your internet browser. In Windows Vista, you have to
install the service pack 1 to enable the card reader to support SDXC cards.
Insert a memory card into the appropriate slot in the card reader (as printed on the
card reader). Pay attention to the correct orientation when inserting the memory card;
do not use force!
If you wish to remove the memory card from the card reader (or to disconnect the
card reader from the computer), wait until all read/write accesses to the memory card
are completed. Only then you should remove the memory card from the card reader.
If the memory card is removed during a read/write access (or the card
reader disconnected from the computer), the data on the memory card can
be damaged. The memory card may possibly even require subsequent re-
formatting.
Reading/Writing to Memory Cards
A memory card inserted into the card reader will be integrated in the same way as a
conventional removable media drive. With the Windows File Manager you can now
read the data on the memory card (or store data on the memory card) in the same way
as you use a USB hard drive or a USB stick.
The maximum speed attainable when reading / writing a memory card depends on
your memory card. Therefore, with slower memory cards or while writing onto the
memory card it is normal that the data transfer rate does not increase if you use the
card reader on a USB3.0 port instead of a conventional USB2.0 port.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the relevant
statutory regulations.
G
Operating Instructions
Dual SD Card Reader USB 3.0
Item no. 1207926
Intended use
The product can be plugged into a computer’s USB port and it is designed for reading
and writing to appropriate memory cards. All names of companies and products are
the trademarks of the respective owners. All rights reserved.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
fire, electric shock etc. Read the instructions carefully and keep them. Make this prod-
uct available to third parties only together with its operating instructions.
Delivery content
• Card reader
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the war-
ranty/guarantee.
Persons / Product
• The product is not a toy. Keep it out of the reach of children and pets.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Handle the product carefully. Jolts, impacts or a fall even from a low height can
damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the de-
vice.
• Maintenance, modifications and repairs are to be performed exclusively by an ex-
pert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
Connection
Switch on your computer and wait until the operating system has booted completely.
Connect the card reader to a free USB3.0 port on your computer. During the initial
connection, Windows recognises the new hardware; the drivers are already included
in Windows. The card reader can also be connected to a USB2.0/1.1 port, if your com-
puter does not yet have a USB3.0 port. However, this does not result in faster data
transmission.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2014 by Conrad Electronic SE.
Join the conversation about this product
Here you can share what you think about the Renkforce 1207926 Dual SD Card Reader. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.