Manual Planet Bike Protege 5.0 Cycling Computer

Manual

1. Parts List

1 mm

1. Mounting Bracket

2. Wheel Sensor

3. Computer Case

4. Rubber Shims

5. Wheel Magnet

6

. Quick Ties

2 mm

MOUNTING BRACKET

LINE

: LCD Specification : Line 1, 2 and 3 modes do not change

CURRENT SPEED • Miles or Kilometers per hour • 0-99.5 mph/Kph • Increments of 0.5 mph/KphŁ

RIDE TIME, "RTM" • Up to 9:59:59 • Increments of 1 secondŁ

RIDE DISTANCE, "DST" • Up to 999.99 M or K • Increments of 0.01 M or KŁ

ODOMETER, "ODO" • Up to 999.99 M or K • Increments of 0.01 M or K

1Ł

2Ł

3Ł

4

OR

CHANGE MODE TO SCREEN 2 BY PUSHING COMPUTER FORWARD IN BRACKET TO ACCESS:

CLOCK• 12 Hr Format • Indicated by flashing colon ":"

1Ł

2

SCREEN:

Additional Features:

+ Auto-Start/Stop - Automatically starts recording data or stops recording data when you start or stop ridingŁ

+ Auto LCD Off - LCD automatically shuts off to conserve power after 5 minutes of non-use. Clock will still be displayed.Ł

+ MacroMonitor™ LCD display displays up to 4 functions at once, allowing for fewer mode changes.Ł

+ "Buttonless" design for ease of use - push computer forward in bracket to change modes.Ł

+ Weather proof construction and heavy duty wire harness for all-weather use.

4

MOUNTING SENSOR

1

MOUNTING MAGNET

(Front Wheel)

2

3

STEP 1:

Attach the wheel sensor to the right or left fork using two quick ties (diagram #1).

Note: Do not fully tighten quick ties until final placement is determined. We recommend a

sensor placement of 1-2 inches up from hub axle (diagram #1). Position sensor and wire on

backside (toward rider) of fork blade to offer protection from debris while riding.Ł

Ł

STEP 2:

Attach magnet to spoke using screwdriver (diagram #2) so magnet lines up

directly across from one of the flat round dots at the lower or upper portion of wheel sensor

with a distance of 1-2 mm between sensor and magnet (diagram #3).Ł

Caution: Do not over-tighten magnet screw.Ł

Ł

STEP 3:

Attach the wire harness to the fork using quick ties (diagram #1). Excess wire can

be wrapped around brake cable before securing bracket to handlebar. Note: Allow slight wire

slack between fork and brake cable for turning handlebars.Ł

Ł

STEP 4:

Attach the computer bracket to the handlebars near the stem (diagram #4). Use

any combination of rubber shims to fit different diameter handlebars. Tighten the screw so

the bracket will not rotate on the handlebars. Slide the computer head into the bracket until it

"snaps" into place.Ł

Ł

STEP 5: TEST. Install computer head into bracket and rotate front wheel to test for proper

function of magnet/wheel sensor alignment. The mph/kph indicator will flash if the sensor and

magnet are properly aligned. Tighten quick ties on sensor when correct alignment is acheived.Ł

Ł

TO REMOVE COMPUTER HEAD FROM BRACKET: Push the computer in the opposite direction

you would to mount it (diagram #5). The computer head will "snap" out. Note: You may have

to push hard, do not be afraid of breaking it, it will pop out.

Line up SensorŁ

and MagnetŁ

at same levelŁ

Ł

* 1-2 mm apartŁ

Ł

* DO NOT line upŁ

Magnet betweenŁ

flat round dotsŁ

on Sensor.

COMPUTER HEAD REMOVAL

5

2. Mounting Instructions

3. Functions, Specifications & Additional Features

PUSH AND RELEASE FORŁ

MODE

Ł

CHANGE

Ł

CAUTION:Ł

HOLD FORŁ

LESS THAN ONE SECONDŁ

OR YOU WILL RESET ALLŁ

OF THE RIDE DATA

Congratulations and thank you for your purchase of the Planet

Bike Protegé Bicycle Computer. The Protegé represents a

breakthrough in bicycle computer design and function. The

MacroMonitor™ LCD display, "buttonless" design, and overall

compact size offer advantages to you the cyclist that no other

computer can match. In addition, Planet Bike will donate 25% of

our profits from this purchases and any other Planet Bike

product you buy, to non-profit bicycle advocacy groups to

further benefit your cycling experience. Enjoy your new Protegé

Bicycle Computer and thank you for making a difference!

FrontŁ

of bike

RearŁ

of bike

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Planet Bike Protege 5.0 Cycling Computer. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Planet Bike. They might be able to provide an original manual. Are you looking for the manual of your Planet Bike Protege 5.0 Cycling Computer in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Planet Bike Cycling Computers
More manuals of Cycling Computers

Frequently Asked Questions about Planet Bike Protege 5.0 Cycling Computer

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Planet Bike Protege 9.0 Wireless Cycling Computer

Manual

Planet Bike Protege 9.0 Cycling Computer

Manual

Planet Bike Protege 8.0 Cycling Computer

Manual

CicloSport CicloMaster CM 209 Cycling Computer

Manual

Crivit IAN 270550 Cycling Computer

Manual

CicloSport CicloMaster CM 9.3A plus Cycling Computer

Manual

Polar CS200 Cycling Computer

Manual

Echowell BC 8 Cycling Computer

Related categories