Manual Philips AT610 AquaTouch Shaver

Manual

- Do not use the supply unit in or near wall

sockets that contain an electric air freshener

to prevent irreparable damage to the supply

unit.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable standards and

regulations regarding exposure to electromagnetic fields.

General

- This shaver is waterproof (Fig. 3). It is suitable for use in the bath or

shower and for cleaning under the tap. For safety reasons, the shaver

can therefore only be used without cord.

- The supply unit is suitable for mains voltages ranging from 100 to 240

volts.

- The supply unit transforms 100-240 volts to a safe low voltage of less

than 24 volts.

- Maximum noise level: Lc = 69dB(A)

Charging

Charge the shaver before you use it for the first time and when the display

indicates that the battery is almost empty. When you charge the shaver for

the first time or after a long period of disuse, let it charge for at least 10

hours.

A fully charged shaver has a shaving time of up 30 minutes.

The shaving time may be less than expected as a result of your shaving

behavior, your cleaning habits or your beard type.

Note: You cannot use the shaver while it is charging.

Charging with the supply unit

1 Make sure the shaver is switched off.

2 Put the small plug in the shaver and put the supply unit in the wall

socket.

The display of the shaver indicates that the shaver is charging.

3 After charging, remove the supply unit from the wall socket and pull the

small plug out of the appliance.

Charge indications

Battery low

When the battery is almost empty (when there are only 5 or fewer shaving

minutes left), the charging light lights up orange (Fig. 4).

- When you switch off the shaver, the charging light continues to light up

orange for a few seconds.

Charging

When the shaver is charging, the charging light lights up green continuously

(Fig. 4).

- The charging light will keep lighting up green when the shaver is fully

charged.

Using the shaver

Always check the shaver and all accessories before use. Do not use the

shaver or any accessory if it is damaged, as this may cause injury. Always

replace a damaged part with one of the original type.

- Use this shaver for its intended household use as described in this

manual.

- For hygienic reasons, the shaver should only be used by one person.

- Trimming is easier when the skin and hair are dry.

Note: This shaver can only be used without cord.

Switching the appliance on and off

1 To switch the appliance on or off, press the on/off button once (Fig. 5).

Shaving

Shaving tips

- Use the shaver with shaving gel or foam for extra skin comfort, or use the

shaver dry for extra convenience.

-

We advise you to use the shaver with shaving gel or foam when you

use it for a wet shave. Do not use thick shaving cream or shaving oil

with this shaver.

-

When you use the shaver for dry shaving, we advise you to make sure

your skin is fully dry so that the shaver glides smoothly over your skin.

- For best results on skin comfort, pre-trim your beard if you have not

shaved for 3 days or longer.

- For optimal shaving results, make circular movements during use.

- The shaver is waterproof and can be used in the bath or shower.

- Your skin may need 2 or 3 weeks to get accustomed to the Philips

shaving system.

Wet shaving

For a more comfortable shave, you can also use this appliance on a wet

face with shaving foam or shaving gel.

To shave with shaving foam or shaving gel, follow the steps below:

1 Apply some water to your skin (Fig. 6).

2 Apply shaving foam or shaving gel to your skin (Fig. 7).

3 Rinse the shaving unit under the tap (Fig. 8) to ensure that the shaving

unit glides smoothly over your skin.

4 Switch on the appliance.

5 Move the shaving heads over your skin in circular movements to catch all

hairs growing in different directions (Fig. 8). Exert gentle pressure for a

close, comfortable shave.

Note: Rinse the shaving unit regularly to ensure that it continues to glide

smoothly over your skin (Fig. 8).

6 Dry your face.

7 Clean the appliance after use.

Note: Make sure you rinse all foam or shaving gel off the appliance.

Dry shaving

1 Switch on the appliance.

2 Move the shaving heads over your skin in circular movements to catch all

hairs growing in different directions (Fig. 8). Exert gentle pressure for a

close, comfortable shave.

Note: Do not press too hard, this can cause skin irritation.

3 Clean the appliance after use.

Trimming

You can use the trimmer to groom your sideburns and moustache.

1 Push the trimmer release slide downwards to open the trimmer (Fig. 10).

2 Switch on the appliance.

3 Hold the trimmer attachment perpendicular to the skin and move the

appliance downwards while you exert gentle pressure.

4 Clean the trimmer after use.

5 Close the trimmer (Fig. 11).

Cleaning and maintenance

Cleaning the shaver under the tap

Clean the shaver after every shave for optimal performance. For the best

cleaning results, we advise you to use Philips Cleaning spray (HQ110).

Always unplug and switch off the shaver before you clean it.

Note: Water may leak from the socket at the bottom of the shaver when you

rinse it. This is normal and not dangerous because all electronics are

enclosed in a sealed power unit inside the shaver.

Be careful with hot water. Always check if the water is not too hot, to

prevent burning your hands.

Never dry the shaving unit with a towel or tissue, as this may damage the

shaving heads.

1 Place your thumb under the shaving unit and push the shaving unit off

the shaver (Fig. 12).

Note: Make sure to hold the shaving unit while doing so.

2 Rinse the hair chamber under the tap (Fig. 13).

3 Rinse the inside of the shaving unit under a warm tap (Fig. 14).

4 Rinse the outside of the shaving unit under a warm tap (Fig. 15).

Thorough cleaning

5 Turn the lock anticlockwise and remove the retaining frame from the

shaving unit (Fig. 16).

6 Remove and clean one shaving head at a time (Fig. 17). Each shaving

head consists of a cutter and a guard.

Note: Do not clean more than one cutter and guard at a time, since they

are all matching sets. If you accidentally mix up the cutters and guards, it

may take several weeks before optimal shaving performance is restored.

7 Remove the cutter from the shaving guard and rinse it with water (Fig.

18).

8 Rinse the inside and outside of the shaving guard with water (Fig. 19).

9 Put the shaving heads back into the shaving unit (Fig. 20). Make sure that

the projections of the shaving heads fit exactly into the recesses.

10 Put the retaining frame back into the shaving unit and turn the lock

clockwise.

11 Reattach the shaving unit (Fig. 22).

Note: If you cannot reattach the shaving unit properly, check if you have

inserted the shaving heads properly and if the retaining frame is locked.

12 Carefully shake off excess water, open the shaving unit again and leave it

open to let the shaving unit dry completely.

Caution: Be careful not to hit the shaving unit against anything while

you shake off excess water.

Cleaning the trimmer

Clean the trimmer every time you have used it.

1 Switch off the shaver.

2 Push the trimmer release slide downwards to open the trimmer (Fig. 10).

3 Rinse the trimmer under a hot tap (Fig. 23).

4 Close the trimmer (‘ click’) (Fig. 11).

Tip: For optimal trimming performance, lubricate the trimmer teeth with

a drop of sewing machine oil every six months (Fig. 24).

Replacement

Replacing the shaving heads

For maximum shaving performance, we advise you to replace the shaving

heads every two years. Replace damaged shaving heads immediately.

Always replace the shaving heads with original Philips shaving heads' (see

'Ordering accessories').

1 Switch off the appliance and disconnect it from the power outlet.

2 Place your thumb under the shaving unit and push the shaving unit off

the shaver (Fig. 12).

Note: Make sure to hold the shaving unit while doing so.

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Philips AT610 AquaTouch Shaver. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Philips. They might be able to provide an original manual. Are you looking for the manual of your Philips AT610 AquaTouch Shaver in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Philips Shavers
More manuals of Shavers

Frequently Asked Questions about Philips AT610 AquaTouch Shaver

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Philips RQ1160CC Shaver

Manual

Philips HP6320 Shaver

Manual

Philips PQ229 Shaver

Manual

Philips AT758 AquaTouch Shaver

Manual

Philips YS522 Shaver

Manual

Philips PQ218 Shaver

Manual

Philips HQ33 Shaver

Manual

Philips PQ227 Shaver

Related categories