Manual Panasonic VL-V522LSX Intercom System

Manual

Door Station

Model No. VL-V522L

Installation and Operation Guide

Thank you for purchasing a Panasonic product.

LPlease read this guide before using the unit and save for

future reference.

LPlease read this guide carefully, and install the unit safely

and correctly by following the instructions. Panasonic

assumes no responsibility for injuries or property damage

resulting from failures arising out of improper installation or

operation inconsistent with this guide.

LIn this guide, the sufx of each model number (e.g., the “BX”

in “VL-V522LBX”) is omitted unless necessary.

For your safety

To prevent severe injury and loss of life/property, read this section carefully

before using the unit to ensure proper and safe operation of your unit.

WARNING

L

To reduce the risk of electric shock, do not disassemble this unit. Refer

servicing to an authorized service center when service is required. Opening or

removing covers may expose you to dangerous voltages or other risks. Incorrect

reassembly can cause electric shock when the unit is subsequently used.

LNever install wiring during a lightning storm.

L

When existing chime wires are used, it is possible that they contain AC voltage.

Electric shock or unit damage could result. Contact an authorized service center.

CAUTION

LInstall the unit securely adhering to the instructions in this guide to prevent

it from falling off the wall. Avoid installing onto low-strength walls, such as

gypsum board, ALC (autoclaved lightweight concrete), concrete block, or

veneer (less than 18 mm thick) walls.

LIf the wiring is underground, do not make any connections underground.

LIf the wiring is underground, use a protection tube.

PNQW4842ZA C0915NS0

Included accessories

LWood screws ..................2

(3.8 mm × 20 mm)

L Attached to the bag the door station

is in.

A Lens cover

B Camera

C LED lights (for Illumination)

D {CALL} button and indicator

LThe indicator is lighted with a red LED

while the power is on.

LWhen a visitor presses the call button,

a ringer tone will ring.

E Water drain holes

F Panel

G Speaker

H Microphone

N Door station image quality

The following phenomena may occur. They are not malfunctions.

LIf the sun can be seen, its center appears as a black dot.

LAt night or when there is poor lighting in the doorway, the image colors

become unclear. If there is a light in the doorway, the image may appear

greenish. When the door station’s LED lights are off, the image of the

subject may be displayed in black and white (or bluish-purple).

LDuring the daytime or if there is bright light in the doorway, the color of the

visitor’s clothing may appear differently to the actual color.

Before installation

To avoid malfunction or communication disturbances, do not install the door station

in the following locations:

– Places where vibration or any other kind of impact occurs.

– Places near hydrogen sulde.

Installation position of the door station and camera range

N Views when the camera is facing forwards at 0° (default).

LExample: Installation height is 1450 mm (standard position).

Side view Top view

Image range:

960 mm

500 mm

87°

1450 mm

1810 mm

Center of

the door

station

66°

650 mm

Image

range

1160 mm

500 mm

Note:

LThe measurements and angles are for reference purposes and may vary

depending on the environment.

LIf a strong light is shining on the door station, the visitor’s face may not be

distinguishable.

Do not place the door station in the following locations.

– Where most of the background is the sky.

– Where the background is a white wall, and direct sunlight will reect off it.

– Where direct sunlight will shine on the door station.

LDo not place the door station in the locations where echoing occurs, causing the

unit to beep frequently.

L Make sure the rear of the door station is not subject to water.

Wire type and distance

LWire (between the main monitor station and the door station):

Type Distance Loop resistance

General cable CAT-3 Maximum 50 m

10 Ω or lower

General cable 22 AWG (ø 0.65) Maximum 100 m

The camera angle can be adjusted using the camera angle control lever on the

rear of the door station (step 3, “Installing the door station”), so that the image

range can be changed.

N

Side view when the camera is installed

lower than the standard position, and

facing upwards at 15°.

L

Example: Installation height is 1100 mm.

N

Top view when the camera is facing

left or right at 15° *

1

.

L

Example: Camera angle faces left 15°.

Center of

the door

station

1690 mm

1100 mm

66°

710 mm

500 mm

980 mm

Image

range

Image range:

1080 mm

810 mm

500 mm

87°

270 mm

*

1

If the camera points 15° upwards, the left or right angle is less than 7°.

Installing the door station

Important:

LOn the bottom surface of the door station, there are holes to allow water to

drain. Do not cover them up when installing.

1 Remove the mounting base.

A Open the screw

cover.

TScrewdriver

Mounting base

B Loosen the

mounting screw.

Water drain

holes

2 Attach the mounting base to the wall securely using the wood screws

(3.8 mm x 20 mm).

LInstall the mounting base on a vertical at wall.

LBefore drilling, refer to “Before installation” for installation location.

83.5 mm

Wall

Wire (Not included)

Mounting base

Wood screws

3 Adjust the camera angle using the camera angle control lever.

Important:

LWhen the camera angle is adjusted to the upper left or upper right, the

image may be slightly distorted.

LThe angle can also be adjusted to

the left or upper left.

<Examples of camera angle>

<Facing forwards> <Facing upwards> <Facing right> <Facing upper right>

Rear view

Camera angle

control lever

Left

(maximum 15°)

Right

(maximum 15°)

Upwards

(maximum 15°)

4 Connect the wire, then mount the door station to the mounting base.

A Unscrew the screws.

Push in the wire to the terminal connectors

(non polar), then tightly fasten the screws.

Wire (connecting to the main monitor station)

C Fasten the screw,

then close the

screw cover.

B Mount the door station

to the mounting base.

Specications

Power source: Supplied by the main monitor station

Dimensions:

Approx. height 131 mm x width 99 mm x depth

36.5 mm (Excluding protruding sections)

Mass (Weight): Approx. 200 g

Operating environment: -15 °C to 55 °C, Up to 90 % RH

(Relative Humidity) non condensing

Installation method: Wall mount (Wall mount base included)

Lighting method: LED lights

Minimum illuminance required:

1 lx (within Approx. 50 cm from the camera lens)

Viewing angle: Horizontally: Approx. 87°

Vertically: Approx. 66°

Note:

LDesign and specications are subject to change without notice.

LThe pictures and illustrations in these instructions may vary slightly from the

actual product.

A

B

C

D

E

F

G

H

1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan

http://www.panasonic.com

© Panasonic System Networks Co., Ltd. 2015

Location of controls

Cleaning

Clean the unit with a soft, dry cloth when cleaning. For excessive dirt, wipe the unit

with a slightly damp cloth.

Important:

LDo not use anything containing alcohol, polish powder, powder soap,

benzine, thinner, wax, petroleum, or boiling water.

Also do not spray with insecticide, glass cleaner, or hair spray.

This could cause a change in color or quality.

Important information

Disposal of Old Equipment (Only for European Union and countries with

recycling systems)

1

This symbol (A) on the products, packaging, and/or accompanying documents

means that used electrical and electronic products must not be mixed with general

household waste.

For proper treatment, recovery and recycling of old products, please take them to

applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent

any potential negative effects on human health and the environment. For more

information about collection and recycling, please contact your local municipality.

Penalties may be applicable for incorrect disposal of this waste, in accordance with

national legislation.

Information on Disposal in other Countries outside the European Union

Above symbol (A) is only valid in the European Union. If you wish to discard this

product, please contact your local authorities or dealer and ask for the correct

method of disposal.

For Europe

For detailed information about the Declaration of Conformity, refer to the

documentation provided with the main monitor station used with door station.

We declare under our sole responsibility that the product to which this declaration

relates is in conformity with the standard or other normative document following the

provisions of Directive 2004/108/EC.

Ecodesign information

Ecodesign information under EU Regulation (EC) No. 1275/2008 amended by (EU)

Regulation No. 801/2013. From 1 January 2015.

Please visit here: www.ptc.panasonic.eu

Click [Downloads]

→ Energy related products information (Public)

Power consumption in networked standby and guidance are mentioned in the web

site above.

Authorised Representative in EU:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Panasonic VL-V522LSX Intercom System. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Panasonic. They might be able to provide an original manual. Are you looking for the manual of your Panasonic VL-V522LSX Intercom System in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Panasonic Intercom Systems
More manuals of Intercom Systems