Manual Panasonic ER-221 Hair Clipper

Manual

8

Blade life

Blade life will vary according to the

frequency and length of use. For ex-

ample, using the unit for 10 minutes

every 3 days, the life expectancy is

approximately 3 years. If cutting effi-

ciency is reduced substantially de-

spite proper maintenance, the blades

have exceeded their service life and

should be changed.

The replacement part no. is

WER9602.

Battery life

Battery life will vary according to the

frequency and length of use. If the

battery is charged 3 times a month,

the service life will be approximately

6 years. If the unit is left without be-

ing charged for more than 6 months,

the charge will drain from the battery

and their service life may be short-

ened. Therefore, even when not us-

ing regularly, it is recommended that

the unit be recharged at least once

every 6 months.

For environmental protec-

tion and recycling of

materials

This trimmer contains Nickel-Metal

Hydride battery.

Please make sure that the battery is

disposed of at an officially assigned

location, if there is one in your coun-

try.

How to remove the built-in re-

chargeable battery before dis-

posal of the trimmer

The battery in this trimmer is not in-

tended to be replaced by consum-

ers. However, the battery may be re-

placed at an authorized service

center. The procedure described be-

low is intended only for removal of

the rechargeable battery for the pur-

pose of proper disposal.

Always make sure that the battery

have been removed from the trimmer

before disposing of it.

1. Disconnect the adaptor from the

AC outlet, and remove the power

cord from the trimmer.

2. Remove the blade from the trim-

mer.

Remove the screw (a) and detach

the bottom cover (b). (see fig. 19)

3. Detach the dial cover (c), remove

the screw (d) and disconnect the

dial (e).

4. Remove the two screws (f).

5. Detach the housing (g), front

panel (h) and side panel (i), then

remove the trimmer drive rod (j)

(see fig. 20).

6. Remove the two screws (k).

7. Remove the two screws (l) and

disconnect the rubber push plate

(m). (see fig. 21)

8. Remove the screws (n) and dis-

connect housing (o).

9. Disconnect the battery chamber

(p) and remove the battery (q).

(see fig. 22)

9

7

When finishing the edges (see fig.

8) and trimming the moustache

(see fig. 9)

Use the finishing blade of mini trim-

mer.

Slide the trimmer guide up and then

turn the trimmer on (see fig. 7).

To smooth off a beard surface, run

this blade lightly over the surface.

Cutting of hair

Cut hair to the correct height by mov-

ing the trimmer back against the flow

of the hair.

Cutting around the ears

Cut a little, and then gently separate

the trimmer from the hair (see fig. 10).

Cutting the nape of the neck

Bring the trimmer gently away from

the hair to finish (see fig. 11).

(Do not use the trimmer in an in-

verted position. This can cut hair too

deeply.)

Turn off the trimmer (“0•charge”) be-

fore changing the trim height or re-

moving the attachment.

Maintenance

Hold body of the trimmer with

Panasonic mark upwards, place the

thumb against the blades, and push

them away from the main body. (see

fig. 12)

• If washing in water

1. Rinse off any hairs that are stick-

ing to the blade in running water.

(see fig. 13)

2. Rinse out any hairs that are in-

side the trimmer with running wa-

ter. (see fig. 14)

3. Shake the trimmer 4-5 times gen-

tly, wipe off any water drops from

the trimmer and blade, and then

place it onto a towel with the

“Washable” indicator facing

downward to let it fully dry. (see

fig. 15)

4. Apply a few drops of the oil to the

points indicated by the arrows.

(see fig. 16)

5. Remount the blade on the trim-

mer body.

WARNING: Detach the trimmer from

the AC adaptor before cleaning it in

water.

• If cleaning with brush

1. Remove the blade and brush off

the cut hairs from the blade edge.

2. Use the cleaning brush to brush

off the cut hairs from the trimmer

body and from around the blade.

(see fig. 17)

3. Brush the cut hairs out from be-

tween the stationary blade and

the moving blade. Press down on

the lever for cleaning in order to

raise the moving blade, and brush

the cut hairs out from between the

blades. (see fig. 18)

4. Apply a few drops of the oil to the

points indicated by the arrows.

(see fig. 16)

5. Remount the blade on the trim-

mer body.

8

P06-29(ER221欧)04.8.3120:11ページ8

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Panasonic ER-221 Hair Clipper. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Panasonic. They might be able to provide an original manual. Are you looking for the manual of your Panasonic ER-221 Hair Clipper in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Panasonic Hair Clippers
More manuals of Hair Clippers

Frequently Asked Questions about Panasonic ER-221 Hair Clipper

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Panasonic ER-CA65 Hair Clipper

Manual

Panasonic ER-1512 Hair Clipper

Manual

Panasonic ER-HGP65 Hair Clipper

Manual

Panasonic ER-220 Hair Clipper

Manual

Panasonic ER-GC51 Hair Clipper

Manual

Panasonic ER-CA70 Hair Clipper

Manual

Panasonic ER-5209 Hair Clipper

Manual

Panasonic ER-SC60 Hair Clipper

Related categories