Manual Ozito DBS-3100 Drill Bit Sharpener

Manual

MAINTENANCE

DESCRIPTION OF SYMBOLS

CARING FOR THE ENVIRONMENT

TROUBLESHOOTING

Power tools that are no longer usable should not be disposed of

with household waste but in an environmentally friendly way. Please

recycle where facilities exist. Check with your local council authority

for recycling advice.

Recycling packaging reduces the need for landll and raw materials.

Reuse of recycled material decreases pollution in the environment.

Please recycle packaging where facilities exist. Check with your

local council authority for recycling advice.

V Hz

~ W

/min

n

o

Volts

Alternating current

Revolutions or

reciprocation per minute

Double insulated

Warning

Hertz

Watts

No load speed

Regulator compliance mark

• Keep the ventilation vents of the drill bit sharpener clean at all times, if possible,

prevent foreign matter from entering the vents.

• After each use, blow air through the drill bit sharpener housing to ensure it is

free from all dust particles which may build up. Build up of dust particles may

cause the drill bit sharpener to overheat and fail.

• If the enclosure of the drill bit sharpener requires cleaning, do not use solvents

but a moist soft cloth only. Never let any liquid get inside the drill bit sharpener;

never immerse any part of the drill bit sharpener into a liquid.

Carbon Brushes

When the carbon brushes wear out, the drill bit

sharpener will spark and/or stop. Discontinue use

as soon as this happens. They should be replaced

prior to recommencing use of the drill bit sharpener.

Carbon brushes are a wearing component of the drill

bit sharpener therefore not covered under warranty.

Continuing to use the drill bit sharpener when carbon

brushes need to be replaced may cause permanent

damage to the drill bit sharpener. Carbon brushes will wear out after many uses

but when the carbon brushes need to be replaced, take the drill bit sharpener

to an electrician or a power tool repairer for a quick and low cost replacement.

Always replace both carbon brushes at the same time.

Note: Ozito Industries will not be responsible for any damage or injuries

caused by the repair of the drill bit sharpener by an unauthorised person or by

mishandling of the drill bit sharpener.

Sparking visible through the housing air vents

A small amount of sparking may be visible through the housing vents.

This is normal and does not indicate a problem.

Excessive sparking visible through the housing

air vents and/or the drill bit sharpener failing to

operate

May indicate the carbon brushes have worn out and need to be replaced. Carbon

brushes should only be replaced by a qualied electrician or power tool repairer.

The tip of my drill bit is turning blue

This is because the drill bit is overheating. You will need to reduce the amount of

pressure and sharpening time, cool the drill bit in water in between sharpening.

One edge of my drill bit is longer than the other (the centre

point is therefore not centred)

One side of the drill bit has been sharpened for longer than the other. You will

need to sharpen the shorter side for more time and ensure that both sides

are always sharpened for the same amount of time using the same amount of

pressure.

My drill bit is broken (rather than blunt)

The DBS-3100 is not suitable for sharpening broken drill bits. A drill bit in this

condition will take a substantial amount of time to sharpen. Rough the drill bit into

shape rst using a bench grinder.

The motor turns on but the grinding stone does not spin

For this to happen the grinding stone assembly may not be aligned with the ats

on the shaft. Check that the grinding stone assembly is aligned with the ats on

the shaft (see maintenance section).

The drill bit sharpener does not start

The grinder stone may not be moving freely. Turn the grinding stone adjustment

knob anticlockwise to move the grinding stone downwards, this will allow the

grinding stone to turn freely.

Grinding Wheel Assembly SPDBS3100-21A

Switch SPDBS3100-01

Spare parts can be ordered from the Special Orders Desk

at your local Bunnings Warehouse.

For further information, or any parts not listed here, visit

www.ozito.com.au or contact Ozito Customer Service:

Australia 1800 069 486

New Zealand 0508 069 486

E-mail: [email protected]

SPARE PARTS

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Ozito DBS-3100 Drill Bit Sharpener. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Ozito. They might be able to provide an original manual. Are you looking for the manual of your Ozito DBS-3100 Drill Bit Sharpener in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Ozito Drill Bit Sharpeners
More manuals of Drill Bit Sharpeners

Frequently Asked Questions about Ozito DBS-3100 Drill Bit Sharpener

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Ozito DBS-095 Drill Bit Sharpener

Manual

Parkside PBSG 95 A1 Drill Bit Sharpener

Manual

Grizzly H8203 Drill Bit Sharpener

Manual

Darex M3 Drill Bit Sharpener

Manual

Multi-Sharp 30-6532 Drill Bit Sharpener

Manual

Parkside IAN 89169 Drill Bit Sharpener

Manual

Parkside IAN 61094 Drill Bit Sharpener

Manual

Güde GBS 80 Drill Bit Sharpener

Related categories