Home > Household appliances > Hobs > Omega Hobs > Omega OCGG604WB Hob

Manual Omega OCGG604WB Hob

Need a manual for your Omega OCGG604WB Hob? Below you can view and download the PDF manual for free in English. This product currently has 3 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

User ManualDesigned to Enhance

Gas Cooktops

Installation Procedure

• A barrier must be installed to prevent accidental contact

with the cooktop base, where the base of the cooktop is

accessible from below (i.e. Inside a cupboard, etc.).

• A minimum clearance of 25mm must be maintained

between the base and the barrier. This barrier must be made

of any non-combustible, rigid material.

• Ensure that there is an earthed power outlet within 900mm

of the rear right hand side of the cooktop when installed.

This should be accessible at all times.

• A self-adhesive foam tape has been provided to act as a

sealing agent and is to be placed around the edge of the hob

underside. Ensure there are no gaps when applying the tape.

• Take care to ensure that the seals meet without overlapping.

The thickness of this foam tape is 3mm and the width is

10mm. Avoid leaving any visible excess seal after installation

is complete.

• WARNING: Do not use any kind of silicon sealant to seal the

appliance against the benchtop. This will make it difficult

to remove the appliance, which must be accessible for the

service agent to perform any necessary repairs in the future.

• Clamps and screws are supplied with your cooktop.

Fit the pull down clamps supplied to ensure that the cooktop

cannot move after installation. Refer to the diagram shown

below, and the relevant instructions.

• WARNING: Failure to fix the cooktop to the bench could

result in loosening of the gas connection through movement

of the cooktop and a gas leak may result.

• If your benchtop is less than 35mm in thickness, it may be

necessary to fit a spacer between the benchtop and each

clamp to ensure they can be tightened sufficiently.

Fitting the Clamps

Before resuming, ensure you have applied the sealing strips.

Always wear appropriate protection while carrying out

installation, such as gloves and fully enclosed shoes.

To continue with the installation, ensure you have on hand:

a screwdriver, a soft towel, the supplied clamps and screws.

1. Ensure that any loose burner components and trivets have

been removed from the cooktop.

2. Place the hob upside down on a soft surface to protect both

the hob and your work surface from damage.

3. Place the bracket (B) over the holes that match the size of

the screws. There are one set of screw holes in each corner

of the hob. Slightly tighten a screw (C) through the bracket

(B) so that the bracket is attached to the hob whilst still

allowing you to adjust it’s position.

4. In a team of two, carefully turn the hob back over and then

gently lower it into the aperture hole that you have cut-out in

your benchtop.

5. On the underside of the hob, adjust the brackets into a

position that is suitable for your benchtop.

6. Then fully tighten the screws (C) to secure the cooktop into

its final position.

Installation Instructions

(A) Sealing Strip

Rating

Let us know what you think about the Omega OCGG604WB Hob by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Omega OCGG604WB Hob?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Omega OCGG604WB Hob. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Omega OCGG604WB Hob. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Omega. They might be able to provide an original manual. Are you looking for the manual of your Omega OCGG604WB Hob in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand	Omega
Model	OCGG604WB
Category	Hobs
File type	PDF
File size	0.49 MB

All manuals for Omega Hobs
More manuals of Hobs

Frequently Asked Questions about Omega OCGG604WB Hob

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Which pans can be used on an induction hob? Verified

In general all pans that are magnetic can be used on an induction hob. Almost all new pans are suited for induction.

This was helpful (1380) Read more

My hob has a power plug that doesn't fit a regular socket, what should I do? Verified

Many electric hobs (both ceramic and induction) have a different plug. This is because these appliances require a lot of power. Have the installation of the appliance done by a professional.

This was helpful (1308) Read more

Why does the ignition on my range make a clicking sound? Verified

If the range has ben cleaned with a lot of water, the knobs might have gotten wet, triggering the ignition. Let the knobs dry. If the problem persists you should contact the manufacturer.

This was helpful (1118) Read more