p a r t s L i s t a n d i d e n t i f i C a t i o n
Please verify the contents of your MiNewt.200
T
M
system:
A. “O-Ring” Handlebar Mounting Straps
B. Power Module
C. MiNewt.200
TM
Headlamp/handlebar mount assembly
D. AC Adapter
The MiNewt.400
TM
Dual includes:
A. “O-Ring” Handlebar
Mounting Straps
B. Power Module
D. AC Adapter
E. MiNewt.400
TM
Dual
Headlamp/handlebar
mount assembly
M o u n t i n g t h e h e a d L a M p
Depending on the size of your bike’s handlebars, use one of the three “O-Ring” style
mounting straps to attach the headlamp/handlebar mount assembly. Follow the steps
below.
1. Loosen the screw holding the mount assembly to the headlamp.
2. Hold the headlamp and twist the mount assembly, exposing the slot.
3. Place the desired O-ring mounting strap into the slot and twist the mount assembly
back in its original position. The mounting strap is now secure.
4. Before tightening the screw, align the headlamp. Place the headlamp/mounting
assembly on the handlebar and change alignment angle by twisting.
5. When properly aligned tighten the screw.
6. Place the headlamp/mounting assembly on the handlebar. Pull/stretch the
mounting strap under the handlebar, towards the back and loop it over and into
the back slot on the mounting assembly. If you have difficulty getting the mounting
strap into the back slot see the TIP below.
TIP
: The 2 slots on the mounting assembly are different sizes. The larger slot
opening should face the back of the bike, giving more room for attaching the
mounting strap. The smaller slot opening should face forward, reducing the chance of
dropping the mounting strap.
The MiNewt.400
T
M
Dual contains two (2) headlamps. Mount one (1) headlamp, on
each side of the stem, following steps 1 thru 6 above.
M o u n t i n g t h e p o w e r M o d u L e
1. Thread the Velcro strap through the slots on the top of the Power Module.
2. Attach the concave surface of the Power Module to a safe, convenient location on
the handlebars, stem or frame, placing the Velcro strap over the mating surface.
o p e r a t i o n
1. Connect the headlamp cord to the Power Module.
2. Press and release the headlamp power button to turn the light on. Cycle through
the two brightness levels by pressing and releasing the power button.
3. To access the daylight visible flash mode, press and hold the power button for
greater than 3 seconds.
4. To turn the light off from either normal or flash mode, press and hold the power
button for greater than 1 and less than 3 seconds.
L o w B a t t e r y i n d i C a t o r
With approximately 15% battery capacity remaining, the indicator lights on both the
headlamp and Power Module will turn from blue to red.
B a t t e r y C h a r g i n g
The smart charging circuitry is housed in the Power Module and will recharge a fully
discharged battery in less than 4.5 hours.
1. Plug the AC Adapter into the Power Module and then into the wall socket.
2. The Power Module indicator light will be red until the battery pack is fully charged;
then it changes to blue.
3. Unplug the AC Adapter from the Power Module and wall socket, grasping the
connectors rather than the cables.
4. Leaving the Power Module and AC Adapter connected indefinitely will not harm the
batteries.
A
B
C
D
E
LARGER SLOT
Join the conversation about this product
Here you can share what you think about the NiteRider MiNewt 400 Dual Bicycle Light. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.