Manual Motorola C1002LX Wireless Phone

Manual

allowed to be connected to a telephone interface. The termination on

an interface may consist of any combination of devices subject only to

the requirement that the sum of the RENs of all the devices does not

exceed ve.

This equipment meets the applicable Industry Canada Terminal

Equipment & Technical Specications.

Placing the receiver slightly above the ear may result in better

performance for hearing aids with microphones positioned behind the

ear.

Specic Absorption Rate (SAR) information

SAR tests are conducted using standard operating positions accepted

by the FCC with the phone transmitting at its highest certied power

level in all tested frequency bands, although the SAR is determined at

the highest certied power level, the actual SAR level of the phone while

operating can be well below the maximum value, in general, the closer

you are to a wireless base station antenna, the lower the power output.

Before a new model phone is a available for sale to the public, it must be

tested and certied to the FCC that it does not exceed the exposure

limit established by the FCC, Tests for each phone are performed

in positions and locations (e.g. at the ear) as required by the FCC.

This handset has also been tested and meets the FCC RF exposure

guidelines. Use of other accessories may Non-compliance with the

above restrictions may result in violation of RF exposure guidelines.

what will disable alarm equipment, consult your telephone company or

a qualied installer.

If this equipment is malfunctioning, it must be unplugged from the

modular jack until the problem has been corrected. Repairs to this

telephone equipment can only be made by the manufacturer or its

authorized agents. For repair procedures, follow the instructions outlined

under the Limited Warranty.

If this equipment is causing harm to the telephone network, the

telephone company may temporarily discontinue your telephone

service. The telephone company is required to notify you before

interrupting service. If advance notice is not practical, you will be

notied as soon as possible. You will be given the opportunity to correct

the problem and the telephone company is required to inform you of

your right to le a complaint with the FCC. Your telephone company

may make changes in its facilities, equipment, operation, or procedures

that could aect the proper functioning of this product. The telephone

company is required to notify you if such changes are planned.

If this product is equipped with a corded or cordless handset, it is

hearing aid compatible.

If this product has memory dialing locations, you may choose to store

emergency telephone numbers (e.g., police, re, medical) in these

locations. If you do store or test emergency numbers, please:

• Remain on the line and briefly explain the reason for the call before

hanging up.

• Perform such activities in o-peak hours, such as early morning or

late evening.

Industry Canada

Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any

interference, including interference

that may cause undesired operation.

The term “IC: “ before the certication/registration number only signies

that the Industry Canada technical specications were met.

The Ringer Equivalence Number (REN) for this terminal equipment

is 0.0B. The REN is an indication of the maximum number of devices

This Class B digital apparatus complies with Canadian ICES-003.

This device complies with Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation

of the device.

Le present appareil est conforme aux CNR d’Industrie Canada

applicables aux appareils radio exempts de licence. L’exploitation

est autorisee aux deux conditions suivantes : (1) l’appareil ne doit pas

produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout

brouillage radioelectrique subi, meme si le brouillage est susceptible

d’en compromettre le fonctionnement.

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with

technical requirements adopted by the Administrative Council for

Terminal Attachments (ACTA). This Product Complies With 47CFR

PART 68.

The plug and jack used to connect this equipment to premises wiring

and the telephone network must comply with applicable Part 68 rules

and technical requirements adopted by ACTA. A compliant telephone

cord and modular plug is provided with this product. It is designed to be

connected to a compatible modular jack that is also compliant. An RJ11

jack should normally be used for connecting to a single line and an RJ14

jack for two lines. See Installation Instructions in the User’s Guide.

The Ringer Equivalence Number (REN) is used to determine how many

devices you may connect to your telephone line and still have them ring

when you are called. The REN for this product is encoded as the 6th and

7th characters following the US: in the product identier (e.g., if ## is

03, the REN is 0.3). In most, but not all areas, the sum of all RENs should

be ve (5.0) or less. For more information, please contact your local

telephone company.

This equipment may not be used with Party Lines. If you have specially

wired alarm dialing equipment connected to your telephone line, ensure

the connection of this equipment

does not disable your alarm equipment. If you have questions about

FCC, ACTA and IC regulations

FCC Part 15

This equipment has been tested and found to comply with the

requirements for a Class B digital device under Part 15 of the Federal

Communications Commission (FCC) rules. These requirements are

intended to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged

to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modications to this equipment not expressly approved by

the party responsible for compliance could void the user’s authority to

operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation. Privacy of

communications may not be ensured when using this telephone.

To ensure safety of users, the FCC has established criteria for the amount

of radio frequency energy that can be safely absorbed by a user or

bystander according to the intended usage of the product. This product

has been tested and found to comply with the FCC criteria. Both the

Handset may be safely held against the ear of the user. The telephone

base shall be installed and used such that parts of the user’s body other

than the hands are maintained at a distance of approximately 20 cm (8

inches) or more.

than MOTOROLA, BINATONE or its authorized service centers, are

excluded from coverage.

Altered Products. Products or Accessories with (a) serial numbers or

date tags that have been removed, altered or obliterated; (b) broken

seals or that show evidence of

tampering; (c) mismatched board serial numbers; or (d) nonconforming

or non-Motorola branded housings, or parts, are excluded from

coverage.

Communication Services. Defects, damages, or the failure of Products

or Accessories due to any communication service or signal you may

subscribe to or use with the Products or Accessories is excluded from

coverage.

How to Obtain Warranty Service or Other Information?

To obtain service or information, please call:

US and Canada: 1-888-331-3383

Email: [email protected]

You will receive instructions on how to ship the Products or Accessories

at your expense and risk, to a BINATONE Authorized Repair Center.

To obtain service, you must include: (a) the Product or Accessory; (b)

the original proof of purchase (receipt) which includes the date, place

and seller of the Product; (c) if a warranty card was included in your box,

a completed warranty card showing the serial number of the Product;

(d) a written description of the problem; and, most importantly; (e) your

address and telephone number.

These terms and conditions constitute the complete warranty

agreement between you and BINATONE. regarding the Products or

Accessories purchased by you, and supersede any prior agreement

or representations, including representations made in any literature

publications or promotional materials issued by BINATONE. or

representations made by any agent employee or sta of BINATONE, that

may have been made in connection with the said purchase.

Products Covered Length of Coverage

Consumer Products One (1) year from the date of the products

original purchase by the rst consumer

purchaser of the product.

Consumer Accessories Ninety (90) days from the date of the

accessories original purchase by the rst

consumer purchaser of the product.

Consumer Products and

Accessories that are

Repaired or Replaced

The balance of the original warranty

or for ninety (90) days from the date

returned to the consumer, whichever is

longer.

Exclusions

Normal Wear and Tear. Periodic maintenance, repair and replacement

of parts due to normal wear and tear are excluded from coverage.

Batteries. Only batteries whose fully charged capacity falls below 80% of

their rated capacity and batteries that leak are covered by this Warranty.

Abuse & Misuse. Defects or damage that result from: (a) improper

operation, storage, misuse or abuse, accident or neglect, such as

physical damage (cracks, scratches, etc.)

to the surface of the product resulting from misuse; (b) contact with

liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or

the like, extreme heat, or food; (c)

use of the Products or Accessories for commercial purposes or

subjecting the Product or Accessory to abnormal usage or conditions; or

(d) other acts which are not the fault of MOTOROLA or BINATONE., are

excluded from coverage.

Use of Non-Motorola branded Products and Accessories. Defects or

damage that result from the use of Non-Motorola branded or certied

Products or Accessories or other peripheral equipment are excluded

from coverage. Unauthorized Service or Modication. Defects or

damages resulting from service, testing, adjustment, installation,

maintenance, alteration, or modication in any way by someone other

SAVE THESE INSTRUCTIONS

What will BINATONE do?

BINATONE or its authorized distributor at its option and within a

commercially reasonable time, will at no charge repair or replace any

Products or Accessories that does not

conform to this Warranty. We may use functionally equivalent

reconditioned/ refurbished/ pre-owned or new Products, Accessories

or parts.

What Other Limitations Are There?

ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE

DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR

OR REPLACEMENT PROVIDED UNDER THIS EXPRESS LIMITED

WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND

IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OF

IMPLIED. IN NO EVENT SHALL MOTOROLA OR BINATONE BE LIABLE,

WHETHER IN CONTRACT OR TORT (INCLUDING

NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE

PRICE OF THE PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT,

INCIDENTAL, SPECIAL OR

CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE

OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR

OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION

WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR

ACCESSORIES TO THE FULL EXTENT THESE DAMAGES MAY BE

DISCLAIMED BY LAW.

Some jurisdictions do not allow the limitation or exclusion of incidental

or consequential damages, or limitation on the length of an implied

warranty, so the above limitations or exclusions may not apply to you.

This Warranty gives you specic legal rights, and you may also have

other rights that vary from one jurisdiction to another.

10. To avoid interference to nearby appliances, do not place the base of

the phone on or near a TV, microwave oven, or VCR.

CAUTION

To maintain compliance with the FCC’s RF exposure guidelines, place

the base unit at least 8 inches from nearby persons.

Battery Safety Instructions

• Do not burn, disassemble, mutilate, or puncture the battery. The

battery contains toxic materials that could be released, resulting in

injury.

Consumer Products and Accessories

Limited Warranty (“Warranty”)

Thank you for purchasing this Motorola branded product manufactured

under license by Binatone Electronics International LTD (“BINATONE”).

What Does this Warranty Cover?

Subject to the exclusions contained below, BINATONE warrants that

this Motorola branded product (“Product”) or certied accessory

(“Accessory”) sold for use with this product that it manufactured to be

free from defects in materials and workmanship under normal consumer

usage for the period outlined below. This Warranty is your exclusive

warranty and is not transferable.

Who is covered?

This Warranty extends only to the rst consumer purchaser, and is not

transferable.

CAUTION

To reduce the risk of re, use only No. 26 AWG or larger UL Listed or CSA

Certied Telecommunication Line Cord.

Unplug this cordless phone immediately from an

outlet if:

• The power cord or plug is damaged or frayed.

• Liquid has been spilled on the product.

• The product has been exposed to rain or water. Do not retrieve

the handset or base until after you have unplugged the power and

phone from the wall. Then retrieve the unit by the unplugged cords.

• The product has been dropped or the cabinet has been damaged.

• The product exhibits a distinct change in performance.

Installation Guidelines

1. Read all instructions and save them for future reference.

2. Follow all warnings and instructions marked on the product.

3. Do not install this product near a bath tub, sink, or shower.

4. Operate this phone using only the power source that is indicated

on the marking label. If you are unsure of the power supply to your

home, consult with your dealer or local power company.

5. Do not place this product on an unstable cart, stand, or table. This

product may fall, causing serious damage to the product.

6. Adjust only those controls that are covered by the operating

instructions. Improper adjustment of other controls may result in

damage and will often require extensive work to restore the product

to normal operation.

7. Clean this product with a soft, damp cloth. Do not use chemicals or

cleaning agents to clean this phone.

8. Use only the power supply that came with this unit. Using other

power supplies may damage the unit.

9. Because this phone operates on electricity, you should have at least

one phone in your home that operates without electricity in case of

a power outage.

9. General information

If your product is not working properly...

1. Read this User’s Guide.

2. Visit our website: www.motorola.com

3. Contact Customer Service in the US and Canada at

1-888-331-3383

Email: [email protected]

Important safety instructions

Follow these safety precautions when using your phone to reduce the

risk of re, electric shock, and injury to persons or property:

1. Keep all vents and openings of the phone unblocked.

Do not set the phone on a heating register or over a radiator. Ensure

that proper ventilation is provided at the installation site.

2. Do not use while wet or while standing in water.

3. Do not use this product near water (for example, near a bath tub,

kitchen sink, or swimming pool).

4. Do not allow anything to rest on the power cord. Place the power

cord so that it will not be walked on.

5. Never insert objects of any kind into the product vents as that may

result in re or electric shock.

6. Unplug this product from the electrical outlet before cleaning. Do

not use liquid cleaners or aerosol cleaners. Use a damp cloth for

cleaning.

7. Do not disassemble this product. If service or repair work is required,

contact the customer service helpline found in this User’s Guide.

8. Do not overload wall outlets and extension cords.

9. Avoid using during an electrical storm. Use a surge protector to

protect the equipment.

10. Do not use this phone to report a gas leak, especially if you are in the

vicinity of the gas line.

No ring tone

• The ring tone is deactivated.

• Increase the volume.

Caller ID service does not work

• Check your subscription with your network operator.

A phonebook entry cannot be stored

• The phonebook is full. Delete an entry to free memory.

No display

• Try recharging or replacing the batteries.

• Try disconnecting and connecting the base power supply.

• If the LED is not lit up, then try disconnecting and connecting the

base power supply.

Unable to register another handset

• Maximum number of 4 handsets has been reached.

• The display shows

Searching

. You must unregister a handset in order

to register a new one.

Noise interference on your radio or television

• Your base or charger may be too close. Move it as far away as

possible.

7.2.4 Delete an entry

1. Press d to open the Calls list.

2. Scroll u or d to the entry you want.

3. Press m, the display shows

View

.

4. Scroll d to

Delete

and press m. The display shows

Conrm?

.

5. Press m to conrm or b to cancel.

7.2.5 Delete the entire Calls list

1. Press d to open the Calls list.

2. Press m, the display shows

View

.

3. Scroll d to

Delete all

and press m. The display shows

Conrm?

.

4. Press m to conrm or b to cancel.

8. Help

The icon is not scrolling during charge

• Bad battery contact – move the handset slightly.

• Dirty contact – Clean the battery contact with a cloth moistened

with alcohol.

• Battery is full – no need to charge.

No dialling tone

• No power – check the connections. Reset the phone: unplug and

plug back in the electrical outlet.

• Batteries are empty – charge the batteries for at least 24 hours.

• You are too far from the base – move closer to the base.

• Wrong line cable – use the line cable provided.

Poor audio quality

• The base is too close to electrical appliances, reinforced concrete

walls or metal doorframes – move the base at least 3 feet away away

from any electrical appliances.

The icon is blinking or has disappeared

• Handset is not registered to the base – register the handset to the base.

• You are too far from the base – move closer to the base.

7.2.1 View the Calls list

1. Press d to open the Calls list. If there are no calls in the list, the

display shows

List empty

.

• The most recent number or name if stored in the phonebook

is displayed.

2. Press u or d to scroll through the list.

• If the call was answered, icon is displayed as you scroll to the

entry. If the call was unanswered, icon is displayed as you

scroll to the entry.

• If the telephone number is longer than 16 digits, u icon is

displayed. Press b to see the remaining digits.

• Press m to access the option to store the entry in your

phonebook.

• Press m twice to see the time and date of the call.

3. When viewing a calls list number press # to toggle the Calls List

between dierent formats, e.g. YYY-YYYY, AAA-YYY-YYYY or

1-AAA-YYY-YYYY.

7.2.2 Dial a number in the Calls list

1. Press d to open the Calls list.

2. Scroll u or d to the entry you want.

3. Press t to dial the displayed entry.

7.2.3 Save a number from a Calls list number to the phonebook

1. Press d to open the Calls list.

2. Scroll u or d to the entry you want.

3. Press m, the display shows

View

.

4. Scroll d to

Save number

and press m.

5. The display shows

Enter name

.

6. Enter the name and press m. The number is displayed.

7. Edit the number if necessary, then press m. The number is stored.

7. Caller ID and the Calls list

IMPORTANT

To use Caller ID, you must rst subscribe to the service from your network

provider. A subscription fee may be applicable.

To ensure that the caller’s name is displayed, make sure you have stored

the full telephone number, including the area code in the phonebook.

If the call is blocked,

Private

will be displayed.

If the number is unavailable,

Unknown

will be displayed.

If the call is from the operator,

Operator

will be displayed.

If the call is from a payphone,

Payphone

will be displayed.

If the call is from a ringback request,

Ringback

will be displayed.

7.1 Caller ID

If you have subscribed to a Caller ID Service, you will be able to see

your caller’s number on your handset (provided it is not withheld)

prior to answering the call. The display can show the rst 16 digits or 14

characters of the phone numbers.

If your caller’s name and number are stored in the phonebook and a

number match is found, you will see the caller’s name on the display as

well.

7.2 Calls list

The Calls list stores details of your last 50 received calls, including the

phone number, date and time of call.

The Calls list also alerts you when you have unanswered calls.

The caller’s details are stored in the Calls list whether or not you have

answered the call. The list is shared by all handsets registered to the base.

When the list is full, and a new call is received, the oldest entry will be

deleted automatically.

When you have missed call(s) (incoming calls that you haven’t answered)

the display will show

X Missed call(s)

and the icon will flash on all handsets

registered to the base. Press m to see the callers details.

3. When the display shows

PIN

, enter the base PIN and press m.

When the handset registers with the base, it is assigned a handset

number.

6.6.2 Un-register a handset

Use one handset to delete another. You cannot delete the handset that

you are using.

1. Press m, scroll d to

Services

and press m.

2. Scroll d to

Unregister

and press m.

3. Enter the 4 digit master PIN and press m.

Display shows the rst registered handset number.

4. Scroll u or d to select the handset you want to delete and press

m.

Unregistered

is displayed on the handset screen.

6.7 Restore default settings

You can restore your C100xLX to its default (original) settings.

All the handsets that are registered to the base will be retained.

IMPORTANT

Resetting your phone to its default setting will delete all entries in the

Phonebook and Calls list. All handset and base settings will also be reset.

1. Press m, scroll d to

Services

and press m.

2. Scroll d to

Reset

and press m.

3.

Conrm?

is displayed. Press m.

6.8 Default settings

Handset name HANDSET Phonebook Empty

Low battery beeps ON Calls list Empty

Docking tone ON Redial list Empty

Key tone ON PIN code 0000

Ringer tones 1 Dial mode Tone

Ringer volume 3 Flash mode Long (600 ms)

Earpiece volume 1 Keypad lock OFF

6.4 Dial mode

The default C100xLX dialling mode is suitable for your country and

network operator. It is unlikely that you should need to change this

setting unless advised to do so.

1. Press m, scroll d to

Services

and press m.

2. Scroll d to

Dial mode

and press m.

3. Press u or d to select

Tone

or

Pulse

and press m to conrm.

6.5 Switch Auto clock on / o

If you have subscribed to a Caller ID Service, the date and time will be

set on all your handsets whenever a call is received. This feature can be

set to On or O.

1. Press m, scroll to

Services

and press m.

2. Scroll d to

Auto clock

and press m.

3. Scroll d to

On

or

O

then press m to conrm.

6.6 Registration

Up to 4 handsets can be registered to one base station. Additional

handsets must be registered to the base before you can use them.

• The instructions described below apply specically to your C100xLX

handset. If you wish to register another manufacturer’s handset, the

instructions may vary. In this case, please refer to the manufacturer

of the additional handset.

• The Master PIN is required before you can register or unregister

handsets. The PIN is 0000.

6.6.1 Register a handset

At the base:

1. Press and hold the p on the base until the base beeps. You have

120 seconds in which to register a handset.

At the handset:

1. If the handset is not already registered to a base, press m.

2. Or if the handset is already registered to a base, press m scroll d

to

Services

and press m. Scroll d to

Register

and press m.

6. Services

6.1 Call List type

You can set the Call list to show All calls or Missed calls only. If All calls

is selected, press d key in idle and you can view all calls lists. If Missed

calls is selected, press d key in idle and you can view missed call only.

1. Press m, scroll d to

Services

and press m.

2. The display shows

Call list type

, press m .

3. Scroll u or d to select

All calls

or

Missed calls

and press m to

conrm.

6.2 Area code

You can set your local area code into the phone. When a number from

that area code calls only the local number will be displayed and stored.

The area code can be up to 3 digits long.

Note: If the area code is stored in the phone it will not display the full

phone number.

1. Press m, scroll d to

Services

and press m.

2. Scroll d to

Area code

is displayed. Press m.

3. Using the keypad enter the area code and press m to conrm.

6.3 Flash time

Depending on your country and network operator, your C100xLX has

the flash time set as 600 ms (Long). It is unlikely that you need to change

this setting unless advised to do so.

1. Press m, scroll d to

Services

and press m.

2. Scroll d to

Flash time

and press m.

3. Press u or d to select

Short

,

Medium

or

Long

and press m to

conrm.

5.1.5 Battery tones

When you the battery is running low you will hear a warning beep. You

can switch this beep on or o.

1. Press m, scroll d to

Phone setup.

2. Press m. The display shows

Sounds

.

3. Press m. Scroll d to

Battery tone

.

4. Press m, u or d to select

On

or

O

and press m to conrm.

5.2 Handset name

Personalize your handset, with a name or location for example Peter or

Bedroom. Maximum 12 characters.

1. Press m, scroll d to

Phone setup.

2. Press m. The display shows

Sounds

.

3. Scroll d to

Phone name

and press m.

4. Enter the new handset name and press m to conrm.

Delete the current name by pressing b.

5.3 Date & time

1. Press m, scroll d to

Phone setup.

2. Press m. The display shows

Sounds

.

3. Scroll d to

Date & time

and press m.

4. Enter the date using the keypad (e.g. 08--12--14 for 12th of August

2014) and press m to conrm.

5. Enter the time using the 12 hour format

hh:mm

, e.g. 02:45 for 2:45.

6. Scroll u or d to select

am

or

pm

and press m to conrm.

5.4 Language

1. Press m, scroll d to

Phone setup.

2. Press m. The display shows

Sounds

.

3. Scroll d to

Language

and press m.

4. Scroll u or d to select the required language and press m to

conrm.

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Motorola C1002LX Wireless Phone. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Motorola. They might be able to provide an original manual. Are you looking for the manual of your Motorola C1002LX Wireless Phone in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Motorola Wireless Phones
More manuals of Wireless Phones

Frequently Asked Questions about Motorola C1002LX Wireless Phone

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Motorola C1001LX Wireless Phone

Manual

Motorola CD4011 Wireless Phone

Manual

Motorola CD4012 Wireless Phone

Manual

Motorola C1003LX Wireless Phone

Manual

Motorola CD4014 Wireless Phone

Manual

Motorola C1004LX Wireless Phone

Manual

Motorola CD4013 Wireless Phone

Manual

Philips DECT5250S Wireless Phone

Related categories