Home > Do-It-Yourself > Impact Wrenches > Milwaukee Impact Wrenches > Milwaukee 2766-22 Impact Wrench

Manual Milwaukee 2766-22 Impact Wrench

Need a manual for your Milwaukee 2766-22 Impact Wrench? Below you can view and download the PDF manual for free in English. This product currently has 1 frequently asked question, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

Cat. No. 2766-20 Cat. No. 2767-20

Mode RPM IPM Mode RPM IPM

1 0-950 0-1150 1 0-550 0-950

2 0-1500 0-2100 2 0-1400 0-1750

3 0-1800 0-2400 3 0-1750 0-2100

0-1800* 0-2400* 0-1750* 0-2100*

In mode, when run in reverse, the tool will spin

at the above RPM and IPM until the nut breaks free

from the joint. Then, the tool slows to 750 RPM for

better control in removing the nut.

Using the Control Switch

The control switch may be set to three positions:

forward, reverse and lock. Due to a lockout mecha-

nism, the control switch can only be adjusted when

the ON/OFF switch is not pressed. Always allow the

motor to come to a complete stop before using the

control switch.

Push for

Forward

Push for

Reverse

PUSH TO CENTER TO LOCK

1. For forward (clockwise) rotation, push the control

switch in the direction shown. Check the direction

of rotation before use.

2. For reverse (counterclockwise) rotation, push the

control switch in the direction shown. Check the

direction of rotation before use.

3. To lock the trigger, push the control switch to the

center position. The trigger will not work when the

control switch is in the locked position.

Always remove the battery pack before performing

maintenance or changing accessories. Always

lock the trigger or remove the battery pack before

storing the tool and any time the tool is not in use.

Starting, Stopping and Controlling Speed

These tools may be operated at any speed from 0

to full speed.

1. To start the tool, pull the trigger.

NOTE: An LED is turned on when the trigger is pulled.

2. To vary the driving speed, increase or decrease

pressure on the trigger. The further the trigger is

pulled, the greater the speed.

3. To stop the tool, release the trigger.

ASSEMBLY

WARNING

Recharge only with the charger

specied for the battery. For spe-

cic charging instructions, read the operator’s

manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons

and pull the battery pack away from the tool.

WARNING

Always remove battery pack before

changing or removing accessories.

To insert the battery, slide the pack into the body

of the tool. Make sure it latches securely into place.

WARNING

Only use accessories specically

recommended for this tool. Others

may be hazardous.

Use only sockets and other accessories speci-

cally designed for use on impact wrenches and

drivers. Other sockets and accessories might

shatter or break causing injury.

Attaching and Removing Accessories

1/2" Impact Wrench with Pin Detent

(Cat. No. 2766-20)

1. Use only the appropriate size Square Drive Sockets.

2. To attach a socket, align the hole in the accessory

with the detent pin on the anvil. Hold the detent

pin in while pushing the socket onto the anvil.

The detent pin will snap into place in the hole to

secure the socket.

3. To remove the socket, insert a nail or other thin

object into the hole in the accessory and press

in the detent pin. Pull the accessory o󰀨 the anvil.

1/2" Impact Wrench with Friction Ring

(Cat. No. 2767-20)

1. Use only the appropriate size Square Drive Sockets.

2. To attach a socket, align the accessory with the

anvil and push it rmly over the retaining ring.

3. To remove the accessory, pull the accessory o󰀨

the anvil.

OPERATION

WARNING

Always remove battery pack before

changing or removing accesso-

ries. Only use accessories specically recom-

mended for this tool. Others may be hazardous.

To reduce the risk of injury, always wear proper

eye protection marked to comply with ANSI Z87.1.

Using the Drive Control

The drive control button is used to adjust the torque,

rotation speed (RPM), and impact speed (IPM) for

the application.

To select the drive control

Drive Control Button

Mode Indicator

mode:

1. Pull and release the trigger

to turn on the tool. The cur-

rent mode indicator is lit.

2. Press the drive control

button to cycle through

the 4 modes. When the

desired mode indicator is

lit, begin work.

Rating

Let us know what you think about the Milwaukee 2766-22 Impact Wrench by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Milwaukee 2766-22 Impact Wrench?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Milwaukee 2766-22 Impact Wrench. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Milwaukee 2766-22 Impact Wrench. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Milwaukee. They might be able to provide an original manual. Are you looking for the manual of your Milwaukee 2766-22 Impact Wrench in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand	Milwaukee
Model	2766-22
Category	Impact Wrenches
File type	PDF
File size	2.27 MB

All manuals for Milwaukee Impact Wrenches
More manuals of Impact Wrenches

Frequently Asked Questions about Milwaukee 2766-22 Impact Wrench

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Can I store power tools in a shed or garage? Verified

In general, you can store power tools in a shed or garage, even if it sometimes freezes there. However, it is better for the lifespan of the power tool to store it in a dry place without major temperature fluctuations. In a shed or garage, differences in temperature can cause condensation to form, which can cause rust. In addition, tools that run on batteries last shorter and do not charge as well at very low temperatures. To be sure how your power tool needs to be stored, always thoroughly read the user manual.

This was helpful (10) Read more