Manual Makita UB360D Leaf Blower

Manual

10

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot bat-

tery cartridge cool down before charging it.

4. Charge the battery cartridge if you do not use it

for a long period (more than six months).

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before adjusting or checking

function on the tool.

Installing or removing battery cartridge (Fig. 1)

CAUTION:

• Always switch off the tool before installing or removing

of the battery cartridge.

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge.

Failure to hold the tool and the battery cartridge firmly

may cause them to slip off your hands and result in

damage to the tool and battery cartridge and a per-

sonal injury.

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip it

into place. Insert it all the way until it locks in place with a

little click. If you can see the red indicator on the upper

side of the button, it is not locked completely.

CAUTION:

• Always install the battery cartridge fully until the red

indicator cannot be seen. If not, it may accidentally fall

out of the tool, causing injury to you or someone

around you.

• Do not install the battery cartridge forcibly. If the car-

tridge does not slide in easily, it is not being inserted

correctly.

Battery protection system

The battery cartridge is equipped with the protection sys-

tem, which automatically cuts off the output power for its

long service life.

The tool may stop during operation when the tool and/or

battery are placed under the following situation. This is

caused by the activation of protection system and does

not show the tool trouble.

• When the tool is overloaded:

At this time, press the “OFF” button and remove

causes of overload and then press the “HIGH/LOW”

button again to restart. When the tool does not work

even after pressing the “HIGH/LOW” button, the bat-

tery power auto-stop is still at work. Charge the bat-

tery cartridge before use.

• When the remaining battery capacity becomes low:

Recharge the battery cartridge.

Switch action (Fig. 2)

To start the tool, simply press the “HIGH/LOW” button. To

switch off, press the “OFF” button. To change the tool

speed, press the “HIGH/LOW” button. The first press on

this button is for high speed and the second press for low

speed and then each press on this button repeats the

high/low speed cycle alternatively.

Battery remaining capacity indicator (only for

models with Battery BL3622A)

Battery BL3622A is equipped with the battery remaining

capacity indicator. (Fig. 3)

Press the CHECK button to indicate the battery remain-

ing capacity. The indicator lamps will then light for

approx. three seconds.

• When only the lowermost indicator lamp (next to the

“E”) blinks, or when none of the indicator lamps light,

the battery charge has run out, so the tool does not

operate. In these cases, charge the battery or replace

the empty battery with a fully charged one.

• When two or more indicator lamps do not light even

after charging is complete, the battery has reached the

end of its service life.

• When the upper two and lower two indicator lamps light

alternately, the battery may have malfunctioned. Con-

tact your local Makita authorized service center.

NOTE:

• The indicated capacity may be lower than the actual

level during use or immediately after using the tool.

• Depending on the conditions of use and the ambient

temperature, the indication may differ slightly from the

actual capacity.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing the long nozzle (Fig. 4 & 5)

To install the long nozzle, push in onto the blower outlet

of the tool all the way.

To remove the long nozzle, press its both buttons and

with the buttons being pressed pull it out.

Installing the shoulder strap (Fig. 6)

Pull the hanger out of the tool.

Hook the shoulder strap onto the hanger of the tool.

Before use, adjust the length of strap so that it is easy to

work with it.

Indicator lamps

Remaining capacity

70% to 100%

45% to 70%

20% to 45%

0% to 20%

Charge the battery.

The battery may have

malfunctioned.

Lighted

Off

Blinking

E

F

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Makita UB360D Leaf Blower. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Makita. They might be able to provide an original manual. Are you looking for the manual of your Makita UB360D Leaf Blower in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Makita Leaf Blowers
More manuals of Leaf Blowers

Related products

Manual

Makita M4000 Leaf Blower

Manual

Makita UB120D Leaf Blower

Manual

Makita DUB184Z Leaf Blower

Manual

Makita DUB183 Leaf Blower

Manual

Makita BUB360 Leaf Blower

Manual

Makita 4014N Leaf Blower

Manual

Makita UB001CZ Leaf Blower

Manual

Makita DUB361Z Leaf Blower

Related categories