Manual Kelvinator KWH39CRE Air Conditioner

Manual

8 remote control features Kelvinator Air Conditioning

Energy Saver: (only available in "COOLING" and

"DRY" mode)

Press the ENERGY SAVER button to activate or deactivate the

"ENERGY SAVER" function. In this mode, the fan will continue

to run for 1 minute after the compressor shuts off.

Light:

Press this button at start up and the light on the air

conditioner will be turned on or off. Light On is the default at

start up.

Clock:

Press this button, the clock can be set up, icon (image of

clock face required) blinks. Within 5 seconds, the time can be

adjusted by pressing the

+ or – buttons, if you continuously

press oneof these buttons, after 2 seconds , for every 1/2

second, the time will be increased or decreased by one

minute. If you are still pressing the button after the time

has changed by 10 minutes, the time value will increase or

decrease in 10 minutes steps. While the icon continues to

blink, repressing the clock button will stop the blinking and

the clock will be set.

Special Locking Function:

Press the

+ or – button simultaneously to lock or unlock

the keypad. If the remote control is locked, the (insert

padlock icon) will be displayed on it, in that case, press any

button, the icon will flicker 3 times. Repress the two buttons

simultaneously to unlock.

To change Celcius to Farenheit

With the air conditoner switched off, press the "MODE" and

– buttons simultaneously to switch °C and °F.

caution

NEVER operate the air conditioner without the air filter,

as dust/dirt particles can contribute to equipment failure.

Vertical air flow adjustment (manually)

To adjust the vertical air flow direction, adjust any one of the

horizontal louvre blades. When adjusting the horizontal

louver blades up or down, always keep the top or bottom

blades horizontal. This can effectively prevent water droplets

condensing on the front panel of the unit.

SEAL

DRAIN

JOINT

RUBBER

PLUG

Remote Control Operating Instructions:

The hand held remote control unit operates within a range

of 7 metres (23ft) from the receiver located inside the unit.

Any obstruction between the receiver and the hand held

remote may cause signal interference, limiting the ability

to program the main unit.

Each time a remote control button is pressed, a beep will

sound indicating a command (signal) is transmitted and

received on the unit. When the command is received,

the appropriate function will be displayed (temporarily)

in the LED display window and the green indicator light

corresponding to the selection mode will illuminate on

the main control panel.

Note: The LED display will default to show the ambient

room temperature within 10 seconds of all

program commands.

Power:

To turn the (air conditioner) power on/off, aim the remote

control at the receiver (window) on the unit and press the

"POWER" button.

Mode:

Press the "MODE" button to select either "AUTO",

"HEATING", "COOLING", "FAN" or "DRY" mode (Cooling

& Heating model) or "COOLING", "FAN" or "DRY" mode

(Cooling only model).

Set cooling/heating/auto temperature:

Press the "TEMP" (up/down) buttons to select (increase/

decrease) the required operating temperature, the selected

temperature will appear (temporarily) in the LED display.

The temperature settings are adjustable between 16

O

C

and 31

O

C.

Fan:

Press the "FAN" button to select the required operating fan

speed (HIGH, MED or LOW).

Swing:

Press the "SWING" button to activate the swing feature (the

vertical louvres will oscillate automatically from side to side).

Press the "SWING" button again to deactivate the

"SWING" feature.

Timer:

Press the "TIMER" button to activate the "auto start/auto

stop" timer function.

Timer OFF :(only available when the unit is on)

Press the "TIMER OFF" button to activate the auto stop timer

function. THe method of setting is the same as above for

"TIMER ON".

Sleep:

Press the "SLEEP" button to activate the "SLEEP" feature.

Press the "SLEEP" button to deactivate the "SLEEP" feature.

In Cooling mode, the cooling temperature set point will

increase 1 (degree symbol) C per hour after the "SLEEP"

mode is selected. After two hours, the set temperature will

remain constant. In Heating mode, the heating temperature

set point will decrease 1 (degree symbol)C per hour after the

sleep button is pressed and then remain constant.

Operating instructions

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Kelvinator KWH39CRE Air Conditioner. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Kelvinator. They might be able to provide an original manual. Are you looking for the manual of your Kelvinator KWH39CRE Air Conditioner in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Kelvinator Air Conditioners
More manuals of Air Conditioners

Frequently Asked Questions about Kelvinator KWH39CRE Air Conditioner

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Kelvinator KSV70HRG Air Conditioner

Manual

Kelvinator KSV25CRG Air Conditioner

Manual

Kelvinator KWH26HRC Air Conditioner

Manual

Kelvinator KSV26HRE Air Conditioner

Manual

Kelvinator KWH26CRC Air Conditioner

Manual

Kelvinator KWH62HRE Air Conditioner

Manual

Kelvinator KSV80HRF Air Conditioner

Manual

Kelvinator KSV25HRF Air Conditioner

Related categories