Manual Indesit IB 65B60 NE Hob

Manual

FIRST TIME USE

POWER MANAGEMENT

At the time of purchase, the hob is set to the maximum possible power.

Adjust the setting concerning the limits of your home's electrical system as

described in the following paragraph.

N.B: Depending on the power selected for the hob, some of the cooking zone

power levels and functions (e.g. boil or fast heating) could be automatically

limited to prevent the selected limit from being exceeded.

To set the power of the hob:

Once you have connected the device to the mains power supply, you can

set the power level within 60seconds.

Press the far right timer “+“ button for at least 5seconds. The display shows

“PL“.

Press the

button to conrm.

Use the “+“

and

“−“

buttons to select the desired power level.

The power levels available are: 2.5 kW – 4.0 kW – 6.0 kW – 7.2 kW.

Conrm by pressing

.

The power level selected will stay in the memory even if the power supply

is interrupted.

To change the power level, disconnect the appliance from the mains for at

least 60seconds, then plug it back in and repeat the steps above.

If an error occurs during the setting sequence, the

“EE“ symbol will appear,

and you will hear a beep. If this happens, repeat the operation.

If the error persists, contact the After-Sales Service.

ACOUSTIC SIGNAL ON/OFF

To switch the acoustic signal on/o:

• Connect the hob to the power supply;

• Wait for the switch-on sequence;

• Press the “P“ button of the rst keypad at the top left for 5seconds.

Any alarms set will remain active.

DEMO MODE reheating deactivated, see the section on ”Troubleshooting”)

To switch the demo mode on and o:

• Connect the hob to the power supply;

• Wait for the switch-on sequence;

• Within the rst minute, press the fast heating button “P“ of the bottom

left keypad for 5seconds (as shown below);

• “DE“ will show on the display.

ACCESSORIES

POTS AND PANS

Only use pots and pans made from ferromagnetic

material which are suitable for use with induction hobs:

• enamelled steel

• cast iron

• special pots and pans in stainless steel, suitable

for induction cooking

To determine whether a pot is suitable, check for the

symbol (usually

stamped on the bottom). A magnet may be used to check whether pots are

magnetic.

The quality and the structure of the pot base can alter cooking performance.

Some indications for the base's diameter do not correspond to the actual

diameter of the ferromagnetic surface.

Some pots and pans have only a part of the bottom in a ferromagnetic

material, with parts in another material that is not suitable for induction

cooking. These areas may heat up at dierent levels or lower temperatures.

In certain cases, where the bottom is made mainly of non-ferromagnetic

materials, the hob might not recognise the pan and therefore not switch

on the cooking zone.

To ensure optimum eciency, always use pots and pans with a at bottom

that distributes the heat evenly. If the bottom is uneven, this will aect

power and heat conduction.

NOOK

Empty pots or pots with a thin base

Do not use empty pots or pans when the hob is on. The hob is equipped with

an internal safety system that constantly monitors the temperature, activating

the “automatic o“ function where high temperatures are detected. When

used with empty pots or pots with thin bases, the temperature may rise very

quickly, and the “automatic o“ function may not be triggered immediately,

damaging the pan or the hob surface. If this occurs, do not touch anything

and wait for all components to cool down.

If any error messages appear, call the service centre.

Minimum diameter of pot/pan base for the dierent cooking areas

To ensure that the hob functions properly, use pots of a suitable minimum

diameter (refer to the table below).

Always use the cooking zone that best corresponds to the minimum

diameter of the bottom of the pot.

Place the pot making sure it is well centered on the cooking zone in use.

It is recommended not to use pots that exceed the perimeter of the cooking

zone in use.

100 mm 120 mm

220

mm150 mm

ø min.

ADAPTER FOR POTS/PANS UNSUITABLE FOR INDUCTION

Using this accessory makes it possible to use pots and pans that are not

suitable for induction hobs. It is important to bear in mind that using it

aects eciency and consequently the time needed to heat food. Its

use should be limited because the temperatures reached on its surface

depend signicantly on the pot/pan used, its atness and the type of food

being cooked. Using a pot or pan with a smaller diameter than the adapter

disc may cause heat to build up that is not transmitted to the pot or pan

and this could blacken both the hob and the disc. Adapt the diameter of

your pots/pans and the hob to the diameter of the adapter.

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Indesit IB 65B60 NE Hob. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Indesit. They might be able to provide an original manual. Are you looking for the manual of your Indesit IB 65B60 NE Hob in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Indesit Hobs
More manuals of Hobs

Frequently Asked Questions about Indesit IB 65B60 NE Hob

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Indesit IVIA 630 L D C Hob

Manual

Indesit IS 33Q60 NE Hob

Manual

Indesit RI 860 C Hob

Manual

Indesit IVIA 633 C E Hob

Manual

Indesit IS 15Q60 NE Hob

Manual

Indesit RI 1060 C Hob

Manual

Indesit PI 640 AS (GC) Hob

Manual

Indesit IP 640 S (AV) R Hob

Related categories