ELECTRICAL CONNECTION
IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.
ASSEMBLY
ADJUSTMENT TO DIFFERENT TYPES OF GAS
If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label
on the top of the hob, change the injectors.
Remove the information label and keep it with the instructions booklet.
Use pressure regulators suitable for the gas pressure indicated in the Instruction.
• The gas nozzles must be changed by After Sales Service or a qualified technician.
• Nozzles not supplied with the appliance must be ordered from After Sales Service.
• Adjust the minimum setting of the taps.
NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will
go.
IMPORTANT: should you experience difficulty in turning the burners knobs, please contact the After Sales Service for
the replacement of the burner tap if found to be faulty.
REPLACING THE INJECTORS (see the injector table in the Instruction)
ADJUSTING MINIMUM GAS SETTING OF TAPS
REFERENCE TO LOCAL REGULATIONS
Regulation for room ventilation
NOTE: if the appliance is not equipped with safety devices on the burners (thermocouples), the air vents must be increased
by 100%, and must be at least 200 cm
2
), in compliance with M.D. 21 April 1993.
Connection to gas supply
Before connecting the appliance, make sure that the gas supply system complies with standards UNI-CIG 7129 and UNI-CIG 7131.
Gas connection
The connection to the mains gas network or gas cylinder must be made using a rigid copper or steel pipe with fittings complying
with standards UNI-CIG 7129, or using a continuous-surface stainless steel hose complying with standards UNI-CIG 9891.
The maximum length of the hose is 2 m.
The pressure control valves to be used must comply with the UNI EN 12864 standard for gas cylinders and the UNI EN 88
standard for piped methane gas.
REFERENCE TO LOCAL REGULATIONS
Provision for ventilation
The room in which the appliance is installed must have an air supply to current B.S. 5440 - Part 2 standards.
All rooms require a permanent vent in addition to the openable window.
If there are other fuel burning appliances in the same room B.S. 5440 - Part 2 should be consulted to determine the air vent
requirements.
If the appliance is installed in a cellar or basement, it is advisable to provide an air vent of 65 cm, irrespective of the room volume.
Gas Safety Regulations
The law requires that all gas appliances are installed by competent persons in accordance with the current gas safety
regulations. Failure to install appliances correctly may lead to prosecution.
It is in your own interest, and that of safety, to ensure that the law is complied with. The hob should be installed in accordance with
the Gas Safety (Installation and Use) Regulations, the Building Regulations issued by the Department of the Environment and
the Building Standard (Scotland) (Consolidation) Regulations, issued by the Scottish Development Department.
In the G.B., CORGI registered installers work to safe standards of practice.
WARNING
This operation must be performed by a qualified technician.
WARNING
• The electrical connections must comply
with local regulations.
• The earthing of this appliance is
compulsory by law.
• Do not use an extension cord.
After having cleaned the perimeter surface,
apply the supplied gasket to the hob as shown
in the figure.
Position the hob in the opening made according to the measurements given in the section DIMENSIONS AND DISTANCES
TO BE RESPECTED (mm).
NOTE: The power cable must be long enough to allow its removal from above.
Use the brackets provided to secure the hob. Position the brackets at the holes on the bottom of the hob and fix them with
the appropriate screws in order to adapt them to the thickness of the top.
WARNING
This operation must be performed by a qualified technician.
L
N
Earth
(yellow/green)
MIN. 20 mm
MIN. 50 mm
MIN. 15 mm
MIN. 15 mm
Fit a wooden shelf at least 20 mm thick under the hob, at a
distance of at least 15 mm from the bottom of the hob.
MIN. 15 mm
1. Remove the grids A.
2. Remove the burner bodies B.
3. Using a suitable socket spanner, unscrew the injector to be replaced C.
4. Replace it with the injector required for the new type of gas.
5. Refit the injector in D.
6. For models with the triple-crown burner, proceed as shown in the figure:
• After undoing the two screws F and removing the cover G, replace both injectors
H as previously described.
Refit the cover G, ensuring perfect tightness of the seal before turning the hob on.
7. Before installing the hob, remember to apply the gas setting label (included with
the injectors) over the previous setting data.
WARNING
This operation must be performed by a qualified technician.
To ensure that the minimum setting is correctly adjusted, remove the knob E and proceed
as follows:
• tighten screw to reduce the flame height (-);
• loosen screw to increase the flame height (+).
The adjustment must be performed with the tap in minimum gas setting position (small
flame) .
• The primary air of the burners does not need to be adjusted.
• At this stage, light up the burners and turn the knobs from max position to
minimum position to check flame stability.
IE
Join the conversation about this product
Here you can share what you think about the Ignis AKF 110/IX Hob. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.
reply | This was helpful (0) (Translated by Google)