Manual Hoover HHG7WL5WC5X NL Hob

Manual

04 GB

2.3. ADAPTING THE HOB TO DIFFERENT

TYPES OF GAS

To adapt the Hob for use with different types of gas, carry out the

following instructions:

•Remove the grids and burners

•Insert on hexagonal spanner (7 mm) into the burner support (Figure

6)

•Unscrew the injector and replace it with one suitable for the gas to be

used (see gas type table)

2.4. REGULATING THE MINIMUM FLAME

After lighting the burners, turn the control knob to the minimum setting

and then remove the knob (this can easily be removed by applying

gentle pressure).

Using a small «Terminal» type screwdriver the regulating screw can

be adjusted as in Turning the screw clockwise reduces theFigure .8

gas flow, whilst turning it anticlockwise increases the flow – Use this

adjustment to obtain a flame of approximately 3 to 4 mm in length and

then replace the control knob.

When the gas supply available is LPG - the screw to set the idle flame

must be turned (clockwise) to the end stop.

When you have carried out the new gas regulation, replace the old gas

rating plate on your appliance with one (supplied with hob) suitable for

the type of gas for which it has been regulated.

3. USE OF HOB - USER INSTRUCTIONS

This appliance must only be used for the purpose for which it is

intended, domestic cooking, and any other use will be considered

improper and could therefore be dangerous. The Manufacturer will

not be responsible for any damage or loss resulting from improper

use.

Table A

Burner Type

Ø pan/pot

(cm)

AUX

SR

R

DC kW5 MONO

10 - 18

12 - 22

16 - 26

16 - 26

Auxiliary

Semi Rapid

Rapid

Power

(kW)

1,00

1,75

2,70

5,00 NG

4,6 LPG

G20/20 mbar

(methane)

95 l/h

167 l/h

257 l/h

476 l/h

G30/28-30 mbar

(LPG)

73 g/h

127 g/h

196 g/h

334 g/h

For smaller containers the gas burner should be regulated so that the

flame does not overlap the base of the pan. Vessels with a concave or

convex base should not be used.

WARNING: If a flame is accidentally extinguished, turn the knob

to the off position and do not attempt to re-ignite if for at least 1

minute.

If over the years the gas taps become stiff to turn it is necessary to

lubricate them.

Such operation must be carried out only by qualified Service

Engineers.

2)Tighten the joints with the spanner, remembering to twist the

pipes into position.

3)Attach fitting C to mains gas supply using rigid copper pipe or

flexible steel pipe.

IMPORTANT: carry out a final check for leaks on the pipe

connections using a soapy solution. NEVER USE A FLAME.

Also, make sure that the flexible pipe cannot come into contact

with a moving part of the cabinet (eg.adrawer) and that it is not

situated where it could be damaged.

Warning: If gas can be smelt in the vicinity of this appliance turn off

the gas supply to the appliance and call the engineer directly. Do not

search for a leak with a naked flame.

Before using burner, be sure, grid perimeters center the burner as

below figure.

If you are using Cast Iron Grids; underneath the grid, position of it is

stated. Be sure for the exact grid is used in correct position.

3.1. USING THE GAS BURNER

GENERALADVISE

For best results, use cooking vessels with a flat surface. The size of

the surface should match the gas burner side as follows.TableA.

Prior to switching on the gas hob ensure that the burner caps are

correctly placed within their position. This hob is fitted with electronic

ignition to ignite the burner.

To ignite the burners carry out the following:

• Push in and turn anticlockwise to the larger flame symbol or in

position and keep pushed 5 seconds after ignition. The ignition10

system will continue to generate sparks as long as the control knob is

being pressed Warning: If there is no electricity on appliance to ignite

the burner a match or a lighter should be used carrying out the out the

following:

• Place a lighted match or lighter close to the burner

• Push in and turn the knob anticlockwise to the larger flame symbol

or in position and keep pushed 5 seconds after ignition Warning:10

In any case if after 5 seconds the burner has not lit, stop operating the

device and wait at least 1 min before attempting a further ignition of the

burner.

KNOBS CONTROL

Each knob controls each burner as showed in the serigraphy. The

knobs have steps from highest flame to lowest flame.10 Never try to

switch from 0 to 1 (clockwise)

Indicateurs

Brûleur contrôlé par bouton contrôle

Brûleur éteint

Puissance la plus haute et allumage électrique

Puissance la plus basse

0

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Hoover HHG7WL5WC5X NL Hob. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Hoover. They might be able to provide an original manual. Are you looking for the manual of your Hoover HHG7WL5WC5X NL Hob in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Hoover Hobs
More manuals of Hobs

Frequently Asked Questions about Hoover HHG7WL5WC5X NL Hob

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Hoover HHG6BR4K3X Hob

Manual

Hoover HVG7W4SB Hob

Manual

Hoover HGH64SCP W Hob

Manual

Hoover HDI 30 Hob

Manual

Hoover HH64EXFP Hob

Manual

Hoover HIS642MCTT/1 Hob

Manual

Hoover HHG63BDSX Hob

Manual

Hoover HVG74WC5B Hob

Related categories