Home > Children & Babies > Baby Monitors > Graco Baby Monitors > Graco 2M18 Direct Connect Baby Monitor

Manual Graco 2M18 Direct Connect Baby Monitor

Need a manual for your Graco 2M18 Direct Connect Baby Monitor? Below you can view and download the PDF manual for free in English. This product currently has 2 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

Low Battery Indication

Parent Unit

• When the battery is low in the Parent Unit, the low battery symbol will show in the

center of the LCD screen. If operated too long on a low battery, you may also

experience a poor signal and the no connection symbol on the LCD screen will

appear and you will begin to hear a continuous audible beep from the Parent Unit.

• You may either turn off the unit or plug in the A/C adapter to recharge the batteries.

Nursery Unit

• When the batteries are low in the Nursery Unit, the power LED will change from

green to red. You may also experience a poor signal and the no connection symbol

on the LCD screen on the front of the Parent Unit may change and you will begin to

hear the Parent Unit beep.

• You may either turn off the unit, plug in the A/C adapter or replace the batteries.

Out of Range Indication

• If the Parent Unit begins to lose the signal from the Nursery Unit, the no connection

symbol on the LCD screen will appear. Additionally, a continuous audible beep will

be generated to warn the user that the connection to the Nursery Unit has been lost.

• Immediately move the Parent Unit closer to the Nursery Unit to regain connection.

• Once connection has been re-gained, the connection symbol will change to

and

the audible beep will stop.

***Note: It is not uncommon for the Parent Unit to occasionally lose and regain connection

with the Nursery Unit in environments that have a significant amount of obstructions.

Setting Up the Baby Monitor

***NOTE: It is very important that the steps below be followed for first time power-up.

1. For optimum operation, it is best to charge the batteries in the Parent Units for at least 16 hours prior

to use. The rechargeable batteries need to be installed into the Parent Unit before charging - refer to the

“Battery Installation” section. DO NOT turn on power while the unit is charging for the first time.

2. Place the Nursery Unit within 10 feet (3 meters) of your baby. Plug an AC adapter into the jack on the

back of the Nursery Unit. Plug it into a working 120 volt AC outlet.

3. Aim the Nursery Unit toward your baby. Check that there are no walls or large objects that could block

sound transmission.

4. Place the Parent Unit within five (5) feet (1.5 meters) of the Nursery Unit and turn on the Parent Unit

using the On/Off button on right side of the LCD screen.

5. Turn on the Nursery Unit using the On/Off button on the front of the unit.

6. Within a few seconds, the Parent Unit will lock on to the Nursery Unit.

A second later, you will hear a series of beeps and the connection symbol should

change to . Your monitor is now ready for use.

NOTE: If the symbol shows, the Parent Unit is out of range of the Nursery Unit.

• Temperature sensor measures the temperature of the

baby's room and displays it on the LCD of the Parent Unit.

• To change °F to °C, hold Volume down button while

pressing power button for 2 seconds until it beeps, then

press the NightLight button for 2 seconds.

Temperature Sensor

• NOTE: DO NOT put temperature sensor near a heat source or air conditioning vent.

• NOTICE: We have added the thermometer for your convenience. Ambient temperature readings may

be affected by various factors, including (but not limited to) location with respect to windows,

electrical devices and sunlight. We recommend you check the accuracy of the thermometer in its

location with your home thermometer.

Rating

Let us know what you think about the Graco 2M18 Direct Connect Baby Monitor by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Graco 2M18 Direct Connect Baby Monitor?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Graco 2M18 Direct Connect Baby Monitor. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Graco 2M18 Direct Connect Baby Monitor. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Graco. They might be able to provide an original manual. Are you looking for the manual of your Graco 2M18 Direct Connect Baby Monitor in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand	Graco
Model	2M18 Direct Connect
Category	Baby Monitors
File type	PDF
File size	0.97 MB

All manuals for Graco Baby Monitors
More manuals of Baby Monitors

Frequently Asked Questions about Graco 2M18 Direct Connect Baby Monitor

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Why is the range of my baby monitor less than the brochure/manual describes? Verified

Brands tend to state a range that is based on use without obstacles like walls or a distance that covers multiple floors. If the range is insufficient, try to place the baby monitor so that it has minimum obstacles.

This was helpful (657) Read more