Home > Do-It-Yourself > Generator > Generac Generator > Generac QT08054KNANA Generator

Manual Generac QT08054KNANA Generator

Need a manual for your Generac QT08054KNANA Generator? Below you can view and download the PDF manual for free in English. This product currently has 0 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

• Correct AC and DC wire size, connections and

grounding. Control and communication wiring to/

from the transfer switch must be run in a separate

conduit from the AC power leads.

• AC outlet connection.

• Communication wires connected between transfer

switch and generator (HTS only).

• Unit secured to pad.

START-UP CHECKLIST



Before working on the Stationary Emergency

Generator, ensure the following:

• The AUTO/OFF/MANUAL switch is in the OFF

position.

• The power to the block heater and to the battery

charger is switched OFF.

PREPARATION FOR START-UP 

• Remove the fuse from the the control panel. For

the H-100 and R-series: Open the front door of the

control box and remove the 15 Amp ATO fuse in

the lower left-hand corner of the control box.

• Connect the battery cables to the battery. Attach

negative battery cable last.

• Restore power to the GFCI outlet that provides

power to the battery charger.

• Measure the voltage at the battery before and after

the charger is turned on.

• Verify all AC electrical connections are tight at the

circuit breaker and transfer switch.

• Visually inspect entire area looking for loose paper,

plastic wrappings, leaves, etc.

• Check all hoses clamps fittings for leaks or dam-

age.

• Check all electrical plugs throughout the genera-

tor. Ensure each plug is seated correctly and fully

inserted into its receptacle.

• Verify the AUTO/OFF/MANUAL switch is in OFF

position.

• Open the valve to the engine fuel line.

• Bleed the fuel system of air. (necessary for long fuel

lines).

• Open the generator main line circuit breaker.

• Connect a manometer to the gas line and record

the static pressure. It must be as listed in the

Specifications.

• Insert the fuse into the control panel.

• Move the AUTO/OFF/MANUAL switch to the MAN-

UAL position. The engine should now crank and

start.

• Check voltage at the generator terminals.

• For 3-phase units, check phase rotation at the

transfer switch terminals. The generator phase

rotation must match the utility phase rotation.

• Check for coolant, fuel, oil, and exhaust leaks.

• Close the generators main line circuit breaker.

• Turn the generator set off.

• Connect the UTILITY supply to the transfer

switch.

• Set the AUTO/OFF/MANUAL switch to AUTO.

• Disconnect utility power before the transfer

switch.

Engine should start, transfer to load.

Run at least 15 minutes on generator power.

Make certain all 3-phase loads are functioning

correctly (correct phase rotation).

• Reconnect Utility power

Transfer switch will transfer back to Utility and

engine will shut down within the given time

parameters set up for the specific transfer switch

and controller.

• Install all covers, access plates and door panels.

• Put the Owners Manual in a safe and accessible

place.

• Make certain the AUTO/OFF/MANUAL switch is in

the AUTO position.

START-UP INSPECTION 

When a start-up is performed by an Authorized

Service Dealer, a standard three-part form titled

“Start-up Inspection for Standby Power Systems”

(part no. 067377), should be completed by the instal-

lation technician or engineer. See page 1-3 for infor-

mation on locating the nearest Authorized Service

Dealer. The installer should complete the form and

disseminate copies as follows:

• White copy: Mail to Generac Warranty Department,

P.O. Box 340, 211 Murphy Dr., Eagle, WI 53119-

2062.

• Pink Copy: For service file of installing dealer.

• Yellow Copy: For the customer’s records.

8-2

Stationary Emergency Generator

Installation

Install006 Rev. B 10/08

Rating

Let us know what you think about the Generac QT08054KNANA Generator by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Generac QT08054KNANA Generator?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the Generac QT08054KNANA Generator. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your Generac QT08054KNANA Generator. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Generac. They might be able to provide an original manual. Are you looking for the manual of your Generac QT08054KNANA Generator in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.