Manual FERM TDM1006 Drill Press

Need a manual for your FERM TDM1006 Drill Press? Below you can view and download the PDF manual for free in English. This product currently has 1 frequently asked question, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

Loading…

Ferm 53
ELECTRICAL INSTALLATION
The machine is provided with an electrical installation,
which meets the standards. Repairs may only be carried
out by a recognised professional.
The machine is provided with a zero voltage switch.
After the tension drops the machine will not start to
run automatically for safety reasons. The machine must be
switched on again.
Electrical safety
Always check that the power supply corresponds to the
voltage on the rating plate.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm
2
. When using a cable reel always unwind
the reel completely.
ASSEMBLY
Fig.B
Place the footplate (13) in the correct position.
Fasten the column (11) with the bolts supplied (12) to
the footplate.
Now slide the table holder (10) with the table over
the column (11). With the fastening handle (6) the
table is fastened into the desired position.
Now you can assemble the machine casing (7) and
lock with the locking pins (8).
Since the drill spindle is greased in the factory, it is
advisable to run in the machine for approximately 15
minutes at the lowest speed (Fig. B).
Before you push the chuck with pin into the drill
spindle, the inside of the chuck must be completely
grease-free!
SETTING UP THE BENCH DRILL
Before use the drill must be mounted on a fixed base. The
footplate (13) has therefore been provided with drilling
holes. By means of screws the footplate can be fixed to
the base in this place. If it is mounted on a wooden board,
sufficiently large washers must be used on the opposite
side, so that the bolts are not pushed into the wood and
the machine cannot become loose.
The fastening screws may be fastened so far that
the footplate is not under tension or deformed.
When the tension is too high there is a risk of breakage.
ADJUSTING THE NUMBER OF REVOLU-
TIONS OF THE DRILL SPINDLE
Fig.C
The different revolutions of the drill spindle can be adjus-
ted by shifting the V-belt into the belt drive. The machine
is protected by a safety switch so that the machine is
automaticly switched off when opening the casing
The V-belt is shifted as follows:
Open the V-belt cover (14) by loosen the screw on
the right side of the cover.
Loosen the fastening button (18) and slide the engine
in the direction of the machine head, upon which the
V-belt is released.
Shift the V-belt according to the table on the inside of
the V-belt cover.
Tension the V-belt again by pushing the engine plate
(17) to the back. Then the tensioning device is faste-
ned with the fastening button (18).
Close the V-belt cover and the machine is ready again
for use.
Keep the V-belt cover closed during use.
4 Ferm
Download manual in English (PDF, 0.96 MB)
(Consider the environment and only print this manual if it is really necessary)

Loading…

Rating

Let us know what you think about the FERM TDM1006 Drill Press by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.
Are you satisfied with the FERM TDM1006 Drill Press?
Yes No
Be the first to rate this product
0 votes

Join the conversation about this product

Here you can share what you think about the FERM TDM1006 Drill Press. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your FERM TDM1006 Drill Press. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact FERM. They might be able to provide an original manual. Are you looking for the manual of your FERM TDM1006 Drill Press in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

Brand FERM
Model TDM1006
Category Drill Presses
File type PDF
File size 0.96 MB

All manuals for FERM Drill Presses
More manuals of Drill Presses

Frequently Asked Questions about FERM TDM1006 Drill Press

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Can I store power tools in a shed or garage? Verified

In general, you can store power tools in a shed or garage, even if it sometimes freezes there. However, it is better for the lifespan of the power tool to store it in a dry place without major temperature fluctuations. In a shed or garage, differences in temperature can cause condensation to form, which can cause rust. In addition, tools that run on batteries last shorter and do not charge as well at very low temperatures. To be sure how your power tool needs to be stored, always thoroughly read the user manual.

This was helpful (6) Read more
Manual FERM TDM1006 Drill Press

Related products

Related categories