Manual Elektra Beckum KGS 331 Mitre Saw

Manual

15

ENGLISH

Rotating table

For mitre cuts the rotating table (28)

turns through 45° to both sides.

The rotating table lock engages auto-

matically at positive detents provided for

0°, 15°, 22,5°, 30° and 45° mitre angles.

To disengage, actuate the table lock

lever (30) and loosen the locking screw

(29), if necessary.

To lock the rotating table at any desired

in-between angle, tighten the locking

screw.

Track arms

The track arms make it possible to cut

wider workpieces (such as panels). The

track arms can be used for all type of

cuts (standard cross cuts, mitre cuts,

bevel cuts, compound mitre cuts).

The track arms can be locked with the

locking screw (31) in any position.

Sawhead tilt

After loosening the sawhead tilt lock

lever (32) at the rear of the saw, the

sawhead can be steplessly tilted from 0°

through 45° from vertical.

Dust collection attachment

(KGS 331 only)

The dust collection attachment (33)

helps to protect your health and to keep

the shop clean.

A suitable dust collector (optional acces-

sory) must be connected to the suction

port (34) of the dust collection attach-

ment.

1. Place the mitre saw on a sturdy,

level support.

All four feet of the machine's base

must firmly rest on the supporting

surface.

2. Connect to a suitable dust collector

(see "Available Accessories").



Danger!

Dust of certain timber species

(e.g. oak, beech, and ash) can cause

cancer when inhaled: Use a suitable

dust collector:

− when using the saw indoors;

− when working for extended peri-

ods (a total of more then 30 minu-

tes);

− when sawing oak, beech or ash.

7.1 Mains connection



Danger! Electrical Hazard

Operate saw in dry environ-

ment only.

Operate saw only on a power source

matching the following requirements

(see also "Technical Specifications"):

− mains voltage and system fre-

quency conform to the voltage

and frequency shown on the

saw’s reating label;

− fuse protection by a residual cur-

rent operated device (RCD) of

30 mA sensitivity;

− outlets properly installed, earthed

and tested;

Position power supply cable so it

does not interfere with the work and

is not damaged.

Protect power supply cable from heat,

aggressive liquids and sharp edges.

Use only rubber-jacketed extension

cables with sufficient lead cross-sec-

tion (3 x 1.5 mm

2

).

Do not pull on power supply cable to

unplug.

• Before starting work check to see

that the following are in proper work-

ing order:

− saw blade;

− retractable blade guard;

− fence.

• Use personal protection gear:

− dust respirator;

− hearing protection;

− safety goggles.

• Assume proper operating position:

− at the front of the saw;

− in front of the saw;

− to the left of the line of cut.

• If the type of work requires, use the

following:

− work support – for long stock,

which would otherwise fall off the

table on completion of the cut;

− dust collector.



Danger!

Cut only stock of dimensions

that permit for safe holding during the

cutting operation.

Use an auxiliary fence when cutting

small cuttings.

Always hold the workpiece down on

the table and do not jam it. Risk of

kickback.

Never cut several workpieces at the

same time – and also no bundles con-

taining several individual pieces. Risk

of personal injury if individual pieces

30°

15°

45°

30°

15°

0°

0°

28 29 30

45°

30°

15°

45°

30°

15°

0°

0°

31

7. Start of Operation

0

15

30

45

33,9

32

45°-0°

0

15

30

45

33,9

33

34

8. Operation

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Elektra Beckum KGS 331 Mitre Saw. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Elektra Beckum. They might be able to provide an original manual. Are you looking for the manual of your Elektra Beckum KGS 331 Mitre Saw in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Elektra Beckum Mitre Saws
More manuals of Mitre Saws

Frequently Asked Questions about Elektra Beckum KGS 331 Mitre Saw

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Elektra Beckum KGS 301 Mitre Saw

Manual

DeWalt DWS716XPS Mitre Saw

Manual

Makita LS0816F Mitre Saw

Manual

BauKer MS254JF Mitre Saw

Manual

DeWalt DWS779 Mitre Saw

Manual

Titan TTB794MSW Mitre Saw

Manual

Scheppach HM140L Mitre Saw

Manual

Scheppach HM2000 SE Mitre Saw

Related categories