Manual EAGTAC G3L Flashlight

Manual

Estimated period

< 50%

50%-75%

> 75%

Completed 100%

# of Flash

1

2

3

Charge indicator OFF

High Performance Tactical Flashlight

http://www.eagtac.com

sku4564 T/G/S/M-25/30-L/V series

EAGTAC

User Manual

1) Replace new batteries

2)

Ensure retainer ring inside tailcap is tight

3) Clean all conductive contacts

4) Check battery polarity

Troubleshooting - Flashlight does not

turn on or fails to switch between

outputs normally:

WARNING - Lithium and Li-ion batteries

can explode or cause burns if disas-

sembled, shorted, or exposed to high

temperature. Do not mix with used or

other battery types or install backwards.

“No Hassle” EAGTAC Warranty

For repair, replacement, or other inquiries

contact your EAGTAC dealer. You can also

reach our customer support via email at

[email protected].

We warrant our ashlights to be free from

defects in workmanship and materials. We will

repair, replace at our option, without charging

any product or part which is found to be

defective under normal use within 120

months from the date of purchase with the

proof of purchase.

Electronics, chargers and rechargeable batter-

ies are covered for a period of 12 months with

purchase receipt. Such repair or replacement

shall be the purchaser’s sole and exclusive

remedy under this warranty. Normal wear and

tear including batteries draining is not

covered, nor is damage resulting from modi-

cation, misuse, abuse, neglect, faulty battery,

battery leakage, improper maintenance or

repaired by anyone other than EAGTAC or

authorized dealer.

Do not mix new and used lithium or li-ion

batteries. Do not mix batteries with

dierent brand, capacity, voltage, or

install batteries backwards. When the

output starts to dim (this implies battery

is almost drained), replace the batteries.

Do not drain the batteries completely

empty especailly when you’re using two

(or more) batteries in series.

All EAGTAC ashlights are designed to

use button-top battery with protruding

positive terminal. For rechargeable li-ion

battery, use only EAGTAC li-ion battery, or

other protected li-ion battery with com-

patible length and diameter. When using

third party li-ion battery, ensure it is

protected and its protection circuit is able

to oer 10 Amp or higher to allow the

ashlight to function at MAX output.

Battery Safety Precaution

Brightness Adjustment

USB Type-C charging port

LOW: 0.5% 1.5% 3% Strobe (cycle)

MED: 14% 27% 40% Strobe (cycle)

Tailcap

on/o

Quick Start Guide

Remove the battery isolation plastic

disc (if any). Unscrew the tailcap and

insert battery (w/ protrude top) to use.

Ensure the positive battery terminal is

facing the LED. Replace tailcap and

tighten snugly.

LED (Front)

High discharge (10A+) li-ion battery required

Tail-cap

EAGTAC ashlights pack big lumen

output and long beam distance in a

compact, tough and grippy ashlight

body. They oer versatile user interface,

highly ecient LED driver, and fast

battery charging ability. Be crazy lumen

with you in the dark.

Quick Specifications

Charging your battery

Remove the waterproof cover and

insert USB cable to charge. The ash-

light will switch o the LED output

during charge and reports the

estimated charging period once by

ashing the LED.

*USB charging port requirement

User can charge the ashlight using

any 5V USB adapter (rated 2A output

or higher).

Compatible battery charging type

This ashlight only charge a single

protected 3.7V li-ion battery. Do not

charge any other battery type such

as CR123A, 3.7V RCR123A, two 18650

batteries, or any unprotected li-ion.

After charging is done, turn o the

ashlight and replace the waterproof

cap to ensure water tightness.

Charge limit (ON-100% OFF-80%)

During charge, switch on the ash-

light switch at the tailcap to charge to

100%. Leaving the switch in o posi-

tion will only charge the battery to

80% (extend battery life cycle).

Low voltage protection

Output step down when battery

reaches 3V and shuts o at 2.5V to

prevent battery over-discharge.

Basic ON and OFF

Switch on/o the ashlight by pressing

the tailcap switch boot until it clicks. To

momentarily switch on the

light, apply light pressure

on the switch boot.

Adjusting output level

Twist the head to select between three

output levels. You can pre-select the

desired output level before turning on

the flashlight.

Tailcap strobe (o by default)

Switch to MAX level and turn the ash-

light on and o for 20 times to toggle

this setting. With this enabled, a double

press of the switch button (within 1

second) will activate strobe output.

Customize low and medium output

Switch to low or medium output and

turn the ashlight on and o for 20

times to toogle output setting to the

next one.

1st level

2nd, 3rd,

level

Output

100%

20%

0.5%

Level

1st

2nd

3rd

Maintenance

Periodically clean the thread and o-rings

with a lint free cloth and apply a thin coat-

ing of EAGTAC synthetic PTFE lubricant to

the o-rings and the thread.

Clean the battery contact, gold plated

signal pins, PCB board contact area, and

machined thread with a lint free cloth.

(Optional) Apply small amount of Deoxit

red cleaner solution (D100L series) to the

contact area for smooth operation.

LED

Output

Charging Circuit

Voltage

Battery

USB Charger

CREE XHP35/XHP50.2/XHP70.2

XP-L/XM-L2/Nichia 219/Luminus LED

3 brightness levels + AUX

C2500

2.7V to 4.2V

18650 / 21700

2A or higher

Active thermal management

After 30 seconds at MAX output, this

feature activates and continuously

adjusts the MAX output between 60%

to 100% according to tempearture.

Battery level indicator (selected model)

After turning on ashlight or switching

levels, it reports the battery capacity:

Battery Capacity

<30%

30-50%

50-70%

>70%

# of Flash

1

2

3

4

Battery Isolation Disk

Rating

More about this manual

We understand that it’s nice to have a paper manual for your EAGTAC G3L Flashlight. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact EAGTAC. They might be able to provide an original manual. Are you looking for the manual of your EAGTAC G3L Flashlight in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for EAGTAC Flashlights
More manuals of Flashlights

Frequently Asked Questions about EAGTAC G3L Flashlight

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Nitecore EC22 Flashlight

Manual

Nitecore TIP2 Flashlight

Manual

Nitecore P20i UV Flashlight

Manual

Nitecore NU40 Flashlight

Manual

Nitecore EC4GTS Flashlight

Manual

Led Lenser P6R Core Flashlight

Manual

Led Lenser H7R Flashlight

Manual

Nitecore TM10K Flashlight

Related categories